YouTube2Text

What Does a $3600 Grinder Offer?: Kafatek Monolith Max 2 Review and Burr Chat — Transcript

by Lance Hedrick · 7,173 words · 960 segments · language en · Watch on YouTube

Full transcript

  1. 0:00what's up everyone Lance Hedrick here
  2. 0:02and today we're going to talk about the
  3. 0:03cetch monolith Max
  4. 0:062 the only reason I do these kind of
  5. 0:09endgame grinder in machine videos is
  6. 0:11because there is so much we can learn
  7. 0:13about coffee when doing them it's these
  8. 0:16companies that are spending tons of
  9. 0:17money on R&D and that have these more
  10. 0:19expensive equipment that are doing some
  11. 0:21of the most exciting
  12. 0:23Innovations it's a nice thing to
  13. 0:25understand and take lessons from things
  14. 0:26like this for us to better understand
  15. 0:28grinder Theory the what's happening
  16. 0:30between the Burrs with fracture Theory
  17. 0:32and different things like that
  18. 0:34manufacturers have taken some of the
  19. 0:36things I've discussed from these
  20. 0:37Grinders in the past and applied it to
  21. 0:39things that are a bit more budget
  22. 0:43friendly we'll start off by just talking
  23. 0:45about what this grinder purports to
  24. 0:47offer then we're going to dial in
  25. 0:48espresso we'll talk about the workflow
  26. 0:50we'll talk about some of the pros and
  27. 0:51the cons of the setup itself then we'll
  28. 0:54open the grinder up look at the pre-
  29. 0:55breaker we'll switch out the burst to do
  30. 0:57some coar burs in order to play with fil
  31. 1:00after that I'm going to talk about a lot
  32. 1:02of different Burrs so we're going to
  33. 1:03have a big bur chat there so if you want
  34. 1:05to skip to that you can then following
  35. 1:06that I'll have concluding thoughts and
  36. 1:08then we'll end the video
  37. 1:12there there will obviously be
  38. 1:13discussions that are like a typical
  39. 1:15review of whether or not people in the
  40. 1:17market would want this grinder but a lot
  41. 1:19of it will be Laden in kind of things
  42. 1:21that I've learned about grinding and
  43. 1:22things that I think this can do or might
  44. 1:24be Innovative in that help us understand
  45. 1:27grinding in general why do you have two
  46. 1:28grinders well this one is is the
  47. 1:30monolith Max one it is what was released
  48. 1:32prior to this this one is on loan from a
  49. 1:34friend that goes by aonic on Discord he
  50. 1:37reached out and said do you want to
  51. 1:38borrow my monolith Max one and I was
  52. 1:40like absolutely I do and so he sent this
  53. 1:42out to me I've been using it for
  54. 1:44somewhere around eight or nine months
  55. 1:45maybe longer I don't know all I know is
  56. 1:48uh I keep getting asked when is a video
  57. 1:50coming so the video is here I bought
  58. 1:52this one at full price
  59. 1:54$3,600 and had it shipped to me here in
  60. 1:57Portugal and I've been using this since
  61. 1:58like February or March or so I've used
  62. 2:01it quite a bit now these more expensive
  63. 2:04Grinders I tend to use them a lot more
  64. 2:06before I do a review because well
  65. 2:07there's essentially a lot more at stake
  66. 2:09and there's just a lot more to kind of
  67. 2:11understand a lot more nuances a lot more
  68. 2:12bur sets not saying that the cheaper
  69. 2:14Grinders I don't put a ton of effort
  70. 2:15into but obviously when it comes to
  71. 2:18these it's it's just a bit it's a bit
  72. 2:20different coffetek was founded in I
  73. 2:22think about 2012 about 12 years ago in
  74. 2:25Seattle Washington since then they've
  75. 2:27been producing Grinders now they have a
  76. 2:29pretty small repertoire of what they're
  77. 2:31actually doing I believe they just have
  78. 2:32one cone bur grinder that's like a dual
  79. 2:34cone they have a 75 mm flat grinder and
  80. 2:36then they have this Max which is 98 mm
  81. 2:39what's interesting about coffetek is
  82. 2:41they build everything on this grinder in
  83. 2:43house with the exception of the motor
  84. 2:45which comes from Japan I'll link below
  85. 2:47what the motor actually is I believe
  86. 2:48it's 200 WT but it's BLC motor that has
  87. 2:51stepped down from 4,000 RPM to 400 RPM
  88. 2:54using a 10:1 gear system there's a big
  89. 2:57misunderstanding I've noticed with
  90. 2:58Grinders and grinder reviews in general
  91. 3:00and I've probably given Sue some of this
  92. 3:02in Past reviews over a year ago or so
  93. 3:04especially when it comes to these BLC
  94. 3:06type Motors if you're using a a gear
  95. 3:09system you'll get more than enough
  96. 3:11torque hence the niche Duo being a 120
  97. 3:13wat motor being able to grind through
  98. 3:15something like green
  99. 3:17coffee they only ship a few batches a
  100. 3:20year you have to get on pre-orders it's
  101. 3:22kind of difficult people end up
  102. 3:24sometimes selling their pre-order in
  103. 3:25order for other people to get in line
  104. 3:27because it's a big waiting game and if
  105. 3:29you're not quick you can miss out on it
  106. 3:30and you might be in Waiting 6 months to
  107. 3:32a year in order to get your grinder some
  108. 3:34people may place an order in October for
  109. 3:36a February dispatch but then January
  110. 3:38comes along and there is a new feature
  111. 3:40on the grinder but they've already
  112. 3:41ordered they're getting the old stock
  113. 3:43because well small businesses you you
  114. 3:45have to work like that you can't just
  115. 3:46switch everything out right when you
  116. 3:47announce a change it's only from that
  117. 3:49point forward that the new one is in
  118. 3:51effect so that has annoyed some people
  119. 3:53but it makes sense to me there's no way
  120. 3:55to juggle the inventory in a way that
  121. 3:56makes sense to where everyone's going to
  122. 3:58be pleased so I do like this idea of
  123. 4:00continually trying to improve your
  124. 4:02grinder and the fact that most of it is
  125. 4:04retrofittable is is very nice as
  126. 4:06well I've read online that the
  127. 4:09tolerances are within 10 microns on
  128. 4:11everything that would be very impressive
  129. 4:12if true I'm I can't say if it is or is
  130. 4:14not but what I can say is I've been very
  131. 4:16impressed by the build quality of this
  132. 4:17it is put together incredibly well and
  133. 4:19you know that the person behind it is
  134. 4:21definitely type A when it comes to
  135. 4:22making sure everything fits perfectly
  136. 4:26together as I've said this is a 98 mm
  137. 4:28flatbird grinder that has a pre- breaker
  138. 4:31inside that is actually inspired by
  139. 4:32conical
  140. 4:33burs so the beans come in through this
  141. 4:36funnel down through the pre-breaking
  142. 4:38cone bur into the flat burst and then
  143. 4:40out through this
  144. 4:41nozzle normally these single do Grinders
  145. 4:44that have a variable RPM setting the
  146. 4:46lowest they go is around 400 this one
  147. 4:48goes from five literally five which is
  148. 4:50way slower than hand grinding up to 400
  149. 4:53now I wouldn't recommend going to five I
  150. 4:55wouldn't recommend doing 30 it's an
  151. 4:57option I guess if you really want to
  152. 4:59play with but uh I don't see why you
  153. 5:01would want 5 minutes to grind your beans
  154. 5:03just kind of twist it twist it and you
  155. 5:05click it in order to lock in what RPM
  156. 5:07you want down to the tenth of an RPM
  157. 5:09which is really neat it's very granular
  158. 5:11and it's very accurate now in addition
  159. 5:13to that there is a switch down here that
  160. 5:15puts in standby mode which can be
  161. 5:17flipped but when you get your grinder so
  162. 5:18if you receive one and it's not working
  163. 5:19maybe the standby is switched on and
  164. 5:21another switch down here that reverses
  165. 5:23the direction of the motor the reason it
  166. 5:26has this is because the shuriken birds
  167. 5:28that are made in house intend Al spin
  168. 5:30the opposite direction of typical burst
  169. 5:32in fact I don't know of any other 98 mm
  170. 5:34grinder that uses the same direction
  171. 5:36spinning as the shuriken burs do so that
  172. 5:39does take away the opportunity for
  173. 5:40people that already have 98mm Grinders
  174. 5:43and want to buy these burst to try out
  175. 5:44unless you have the capability of
  176. 5:46modding your p100 which I believe some
  177. 5:48people have done in order to reverse
  178. 5:49spin you're kind of
  179. 5:51so they do have a switch on here because
  180. 5:54BC's Direction can be changed with that
  181. 5:56you can switch it and you could place
  182. 5:58other burs in before you get excited it
  183. 6:01does have that pre- breaker I talk about
  184. 6:02and there's no way to switch out that
  185. 6:03Burr because that is a unidirectional
  186. 6:05Burr as well so when you put beans in
  187. 6:08there's no way for it to get caught into
  188. 6:09the grooves and cracked so you can just
  189. 6:11switch the motor Direction on this use
  190. 6:13something else in fact currently I have
  191. 6:14SSP cast 98 mm burs in here uh that do a
  192. 6:18great job and I have it just reversed
  193. 6:21spinning because of the motor in here
  194. 6:23you can actually play with the
  195. 6:24acceleration speed now this is an
  196. 6:27interesting thing that I don't think a
  197. 6:28lot of people realize I think there's a
  198. 6:30capability in the aaya orbit to do a
  199. 6:32limited version of it and then on the
  200. 6:33ultra you can do this as well but
  201. 6:35essentially you can play with the
  202. 6:37acceleration of the motor from 0.5 to 15
  203. 6:40seconds what that means is you can say I
  204. 6:43want this to be a peak of 200 RPM but I
  205. 6:47want it to take 15 seconds to get there
  206. 6:50so if you hotload it you can have it go
  207. 6:52slower and slowly accelerate so that
  208. 6:54there's not a frenzy of jumping beans if
  209. 6:56it accelerates to full speed immediately
  210. 6:59this is not necessarily something to
  211. 7:00play with as much with this new one due
  212. 7:02to its pre- breaker but on the
  213. 7:04predecessor or ones without that
  214. 7:06pre-breaking cone it is definitely an
  215. 7:08interesting thing to kind of play around
  216. 7:09with to take away some of that chaos and
  217. 7:11to give it a bit more uniformity of feed
  218. 7:14into the birds
  219. 7:17themselves this grinder is set at
  220. 7:2030° why 30 I'm not quite sure I'm sure
  221. 7:22that there is something about bearing in
  222. 7:24the load inside of it that it needs to
  223. 7:25be at 30° or it was designed to be at
  224. 7:2830° for that I do know that there are
  225. 7:30some people who have added a
  226. 7:31modification in order to tilt it more or
  227. 7:33you can do the simple arm trick where
  228. 7:35essentially you unscrew two of these
  229. 7:37screws and you can tilt it and kind of
  230. 7:38tighten it for pressure against the body
  231. 7:40I'm not recommending officially you do
  232. 7:42that do that at your own risk but to
  233. 7:44Incline it more to like 45° something
  234. 7:46like the Weber eg1 thumbs wi
  235. 7:49open thumbs wi open now when the birds
  236. 7:53are spinning below 200 RPM there's not
  237. 7:56enough really centrifugal force created
  238. 7:58in order to adject the particles out of
  239. 8:00those burs and into your dosing cup so
  240. 8:02it'll be grinding and they just kind of
  241. 8:04want to stick in there when you tilt it
  242. 8:06more you get more aid from gravity and
  243. 8:08it really helps push that process along
  244. 8:10cof definitely doesn't recommend this
  245. 8:12and probably will not be pleased about
  246. 8:15me talking about it but it is something
  247. 8:16I've seen online and since it's online
  248. 8:18anyway I figured it was something to
  249. 8:20bring up now there is a purge button on
  250. 8:23this new iteration but the fact that it
  251. 8:25tops out at 400 RPM you're not really
  252. 8:27going to get much from The Purge
  253. 8:28especially if you're already grinding at
  254. 8:30400 RPM it's literally not changing the
  255. 8:32speed at all Dennis created this 3D
  256. 8:35printed little holder that can be fit
  257. 8:37into the Porta filter Forks to fit
  258. 8:39specifically the blind Shaker the nozzle
  259. 8:42is like a silicone kind of rubbery U
  260. 8:44material which you know is kind of
  261. 8:46annoying to clean sometimes with it when
  262. 8:48you're done you can kind of sit here and
  263. 8:50Flack away at it what I've noticed is
  264. 8:52when you use the Bellos properly and you
  265. 8:54do it well enough you don't really need
  266. 8:55the
  267. 8:56flacker people come in and see this and
  268. 8:58it's it's very very interesting to them
  269. 9:00and they're always curious what it is
  270. 9:01because it does sort of look like a
  271. 9:03microscope which is is pretty neat
  272. 9:06because when you think about grinding
  273. 9:07you're thinking of these tiny particles
  274. 9:09which you'd need a microscope to see and
  275. 9:11so it's it tends to be a question people
  276. 9:13often have when they come in to Studios
  277. 9:14wait what is that and it's always fun to
  278. 9:16kind of talk about the grinder because
  279. 9:18of that the ugliest thing about it
  280. 9:20without question is the Mr puffer on top
  281. 9:23without it it's not nearly as bad but I
  282. 9:25have noticed I absolutely need rdt for
  283. 9:27it and I have to Bellow quite a bit
  284. 9:29every
  285. 9:30time all right so we've got 20 G dosed
  286. 9:32out I have it on an espresso fine level
  287. 9:34I set it to 250 RPM now I could show you
  288. 9:37at 400 to show you the fastest it can
  289. 9:39grind but I wanted to show you the
  290. 9:40efficacy of The Purge so we're going to
  291. 9:42take a look at this kind of see how long
  292. 9:43it takes to grind noise level is really
  293. 9:45nice it's not too loud not whiny uh but
  294. 9:47anyway let's go ahead and rdt cuz that
  295. 9:49is necessary two nice squirts I'm going
  296. 9:52to shake it
  297. 9:54up then we'll start the grinder to Hot
  298. 9:56Load now with this one I haven't seen
  299. 9:58any stalling this when I had a ton of
  300. 10:00stall in even when it was fully seasoned
  301. 10:02with lightly roasted coffees and they
  302. 10:04even warn of that potentially happening
  303. 10:05if a coffee bean gets stuck perfectly
  304. 10:07between the beans because tolerances are
  305. 10:09so tight between the shaft and the
  306. 10:11carrier it could stall but anyway let's
  307. 10:13dump this in hot loaded 250 RPM and here
  308. 10:16we go
  309. 10:37so here at the end I'm going to hit
  310. 10:39Purge and you can watch how much comes
  311. 10:42out not very much just a lot of chaff
  312. 10:44essentially all right so now that that's
  313. 10:47over I'm going to go and turn it off so
  314. 10:49you can see even with rdt there is still
  315. 10:51some chaff and flyways here there's
  316. 10:53always going to be static with these
  317. 10:54bigger burs so trying to figure out a
  318. 10:56way to do it other than a deionizer
  319. 10:58inside is a bit difficult even with rdt
  320. 11:01unless you want to put a ton but the
  321. 11:02more water you put on it the more
  322. 11:04potential it will have to stick inside
  323. 11:05the funnel now I've read online that
  324. 11:07some people use their finger to kind of
  325. 11:09push those beans out I do not recommend
  326. 11:11doing that instead you can invest one of
  327. 11:13these little camera lens and I just kind
  328. 11:14of stick it in and I'll puff it at the
  329. 11:16end of The
  330. 11:18Grind so you hear there are little bits
  331. 11:20that are getting ground up
  332. 11:22now now they do have the Mr puffer
  333. 11:24itself it kind of like distorts as you
  334. 11:26push down what I like to do is fill the
  335. 11:29hole with the the camera lens cleanser
  336. 11:32and then with this together it's much
  337. 11:34more effective and I can get down lower
  338. 11:36with the tip of that kind of double
  339. 11:40Bellow action the double Bellow you know
  340. 11:44once you have the fully bellowed there's
  341. 11:46just a little bit that comes out maybe
  342. 11:48that's like 003 of a gram it fits just
  343. 11:51on my finger whenever I was running
  344. 11:53tests with this because I rely on really
  345. 11:55precise dose in dose out what I would do
  346. 11:57is run it at 400 RPM so I didn't have to
  347. 11:59purge at the end I would take this right
  348. 12:01inside and immediately would start
  349. 12:03puffing from away in order to dislodge
  350. 12:05anything that may be stuck against the
  351. 12:06walls and then I would kind of puff up
  352. 12:08and down both at the same time double
  353. 12:10puffing you have to kind of prod them
  354. 12:12out on the older one they had this more
  355. 12:14limited number system and you had to
  356. 12:16rely on stickers and just kind of
  357. 12:18assuming where you were at which was a
  358. 12:20lot more painful but now they've they've
  359. 12:23made a great decision of putting the
  360. 12:25sticker here onto the actual housing of
  361. 12:27the grinder and then you can just move
  362. 12:28it around and there's numbers all the
  363. 12:29way around the grinder itself so that
  364. 12:32when you're going to filter and back you
  365. 12:33have 360° worth of numbers which is a
  366. 12:36massive Improvement and such an easy
  367. 12:38thing to change it is of utmost
  368. 12:41importance to run the grinder though as
  369. 12:43you go from course to fine if you don't
  370. 12:44do that you can likely have some issues
  371. 12:46because of course particles can still be
  372. 12:48in those burs and cause some issues you
  373. 12:51can actually get to roughly where you
  374. 12:52want to be with your espresso shot and
  375. 12:54then you can kind of further dial in
  376. 12:55with small changes on the RPM which is
  377. 12:58kind of a unique way to dial in and can
  378. 13:00change how you approach some different
  379. 13:01coffees that's something that fancy
  380. 13:03basket boy spert in the eaf Discord does
  381. 13:06all right we got that espresso pulled
  382. 13:07and here we go it's like a little
  383. 13:13sip oo that is that is acidic that is
  384. 13:16syy acidic and it's pretty nice there's
  385. 13:20kind of this fear behind opening your
  386. 13:21cetch and a big part of it is this
  387. 13:23massive yellow sticker here that says
  388. 13:25this is a high Precision grinder
  389. 13:26assembled with great care do not
  390. 13:28disassemble all caps do not remove
  391. 13:30funnel all caps please read the manual
  392. 13:32if you open it and after that there's an
  393. 13:34issue they don't want it to be on them
  394. 13:36and that makes sense but opening your
  395. 13:38grinder and cleaning it is pretty
  396. 13:39necessary especially if you make a lot
  397. 13:41of coffee I'm not cof Tech whatever you
  398. 13:44do do at your own risk avoiding warranty
  399. 13:45whatever but I've opened them both a
  400. 13:47million times and it's been absolutely
  401. 13:49fine now something you want to be
  402. 13:50absolutely certain of is that these two
  403. 13:52back pins these are lining pins you do
  404. 13:54not misplace these okay so they go into
  405. 13:57the top here and they go right back here
  406. 13:59you cannot you cannot mess with those do
  407. 14:01not lose them and as you're cleaning it
  408. 14:03out be very careful to not allow grounds
  409. 14:05to get into these screw holes cuz you
  410. 14:06know it could mess with the uh evenness
  411. 14:09of pressure going down on it so just be
  412. 14:10very careful when you're opening it up
  413. 14:12now right at top you're going to see
  414. 14:13that outer cone bur in the inside cone
  415. 14:15bur for the pancakes but what I'm going
  416. 14:17to do is take off this bur
  417. 14:19carrier just like so and as you can see
  418. 14:21we already we have some retention right
  419. 14:24here where the feeding is going where
  420. 14:25the pre- braing is happening now we can
  421. 14:27see the inside and as you can see
  422. 14:29there's actually a chunk of coffee right
  423. 14:31here on top of the screw hole now this
  424. 14:33is actually a great example of why screw
  425. 14:35holes suck if you got your bur in and it
  426. 14:38had a chunk out of one of the teeth
  427. 14:40would you think that's defective would
  428. 14:41you be confident that it changes the
  429. 14:44taste of your coffee all right well
  430. 14:45let's just apply that logic to three
  431. 14:47massive holes in your Brewing geometry
  432. 14:49structure let's think about that but
  433. 14:51also yes it does change it quite a bit
  434. 14:53you open up a lot more surface area you
  435. 14:55have a lot more cutting area for the
  436. 14:56beans to go through that is more
  437. 14:58controlled that little screw hole is
  438. 15:00going to cut the bean a bit it's going
  439. 15:01to crush it a bit and as you see it has
  440. 15:03quite a bit of retention and there's
  441. 15:04this big old block of coffee that's
  442. 15:06stuck on it so now we kind of look at
  443. 15:08this pancake Burr now what you're seeing
  444. 15:10here is it's like a flattened pre-
  445. 15:12breaker section of a cone bur which is a
  446. 15:14really great way of doing it because so
  447. 15:16essentially you have the collar right
  448. 15:17here to kind of crack the beans as it's
  449. 15:19being fed through so it kind of meets
  450. 15:21the feeding into the burs as it goes
  451. 15:23through you have this tiny little augur
  452. 15:24right here it's very small very small
  453. 15:26augur I'm not sure how effective it is
  454. 15:28but does seem to be doing something
  455. 15:30because as you can see here a little
  456. 15:32bean got stuck in the augur here's a
  457. 15:34picture I took with my phone after I
  458. 15:36took one of the burs out just to see how
  459. 15:38effective this cone bur was at breaking
  460. 15:41those beans so as you can see they're
  461. 15:42really big chunks they're very few finds
  462. 15:44it does a really good job at just
  463. 15:46breaking them up which is something I'm
  464. 15:47really into I think pre- Breakers are
  465. 15:49necessary on these bigger birds and this
  466. 15:50is a nice way of going at it without
  467. 15:52having tooll out a vertically mounted
  468. 15:54bur set that has a big pre-breaking
  469. 15:56augur which I think is definitely a step
  470. 15:58up from the here which doesn't have a
  471. 16:00pre- breaker or feeder system at all it
  472. 16:01kind of has little fingers that kind of
  473. 16:03scoop the beans into the burs but for
  474. 16:05the most part you're just full out
  475. 16:07sending the dose into the
  476. 16:10burs I still think that there's a big
  477. 16:12Improvement when you slow feed on this
  478. 16:13because the pre- breaker does such an
  479. 16:15efficient job it's so quick to break it
  480. 16:16essentially what happens is when you're
  481. 16:18grinding it breaks all of them very
  482. 16:20quickly and then they kind of just sit
  483. 16:21here and wait to go through the burs
  484. 16:24themselves but let's go ahead I'm going
  485. 16:25to pull the burs off these are the ssw
  486. 16:27burs for those of you who are worried
  487. 16:29that I'm showing Trade Secrets I did get
  488. 16:30permission from the man himself so it's
  489. 16:31all good but anyway we're going to go
  490. 16:33ahead unscrew these and uh bada bada
  491. 16:35boom and he does recommend to use a
  492. 16:37proper wrench with a specific Newton
  493. 16:38meter in order to make sure you're not
  494. 16:40overtightening cuz it can cause some
  495. 16:41warping and then this bottom Burr is
  496. 16:43actually very very tightly put in here
  497. 16:45it's good for alignment it's good for
  498. 16:47the tolerance there but it can be a bit
  499. 16:49of a pain to get out so let's vacuum
  500. 16:51that out and then we'll pull the bur
  501. 16:55out it's not like the p100 where I have
  502. 16:57to use a haird dryer in order to expand
  503. 16:59the aluminum to pop it out so that's
  504. 17:01good but it does take a little bit of
  505. 17:02skill in order to get it out so I take
  506. 17:04you can take like an allen wrench or
  507. 17:05something you can just slowly start to
  508. 17:07wiggle each side I like to grab one of
  509. 17:10the holes with one finger and just kind
  510. 17:12of Leverage it from inside the screw
  511. 17:14hole on the opposite side now as you can
  512. 17:17see nothing on the bottom side nothing
  513. 17:19really in the chamber itself you got a
  514. 17:21little bit of caking on the sides but
  515. 17:23nothing too unexpected we can kind of
  516. 17:25get the rest of the stuff out by just
  517. 17:27kind of sweeping it down through the
  518. 17:28exit
  519. 17:29hole somehow grounds can get under this
  520. 17:32top bur and I'm not really sure how I'm
  521. 17:34sure this will be a fix that'll come in
  522. 17:35a future iteration or even an add-on
  523. 17:37that you can kind of shove underneath
  524. 17:39the bur to ensure it's flush so that
  525. 17:40that doesn't happen cuz that can affect
  526. 17:43the alignment all right and so in the
  527. 17:44end this is essentially all the
  528. 17:45retention you have it looks like a lot
  529. 17:48when it's playay out on the counter but
  530. 17:50in reality it's really not a lot I'll
  531. 17:52even include the bean in there you had
  532. 17:54the bean in there it's probably solidly
  533. 17:55at 6 a little over um but a lot of that
  534. 17:58is not going to be transitioned from
  535. 18:00grind to grind like the stuff underneath
  536. 18:02the bird it's obviously not going
  537. 18:03anywhere once it's there it's
  538. 18:06there now as part of their QC process
  539. 18:09they actually sent me a video of them
  540. 18:11measuring the alignment with a zmm and
  541. 18:15it shows that the perpendicularity and
  542. 18:16flatness was was within two microns so
  543. 18:19of course I pulled out my dial indicator
  544. 18:20in order to verify and sure enough as
  545. 18:24you can see on screen it's hard to get a
  546. 18:27perfect 360 without hitting a divot of a
  547. 18:29screw hole and so that little dip is it
  548. 18:31hits the very little Ridge of one of the
  549. 18:33screw holes I will say you might need to
  550. 18:36align the top burn just because what
  551. 18:37you're relying on these Springs and the
  552. 18:39compression of the four screws going
  553. 18:40into it in order to have that alignment
  554. 18:42but that's a simple marker process if
  555. 18:44you feel the need I've not actually done
  556. 18:46it as you saw when I took mine out I
  557. 18:48found that the coffee was more than
  558. 18:50adequate without having to do anything
  559. 18:52like that I did want to note that when
  560. 18:53replacing your burs or putting the burs
  561. 18:55back in it is recommended and i'
  562. 18:57recommend as well to use shs around the
  563. 18:59edges on this this outer bur and then
  564. 19:01shims on the inside in order to just
  565. 19:03make sure you set it perfectly
  566. 19:05radially these I think are largely
  567. 19:08unnecessary for these new Grinders now I
  568. 19:10understand these are being sold to fit
  569. 19:12the old ones as well and there's no pre-
  570. 19:13breaker but if this is going to be the
  571. 19:15new iteration with this pre-breaking
  572. 19:17cone on top with the pancake Burr I
  573. 19:19think a redesign is called for in order
  574. 19:21to have more finishing teeth space
  575. 19:23currently the the longest finishing
  576. 19:25teeth I'm aware of is on the compact pk1
  577. 19:27100 that has about a centimeter
  578. 19:28finishing teeth if we could spread out
  579. 19:31the Love on that face I think the grind
  580. 19:33particle distribution and the heat
  581. 19:35damage would be a lot different so
  582. 19:37what's happening now is after it hits
  583. 19:39this cone bur it's causing big chunks
  584. 19:41and then it's being fed into these pre-
  585. 19:42Breakers that are big enough for beans
  586. 19:44but don't need to be if these were bevi
  587. 19:46off more or had a little bit you know
  588. 19:48less of an inclination to it in order to
  589. 19:50start cutting it sooner as opposed to
  590. 19:52letting it kind of Rumble around and
  591. 19:53overload the finishing teeth then I
  592. 19:56think we could have something really
  593. 19:57nice on our hands
  594. 20:03all right so we've got the cor Spurs
  595. 20:04back in there we've got our coffee dosed
  596. 20:06out water heat it up so let's go ahead
  597. 20:07dump the beans in and then here we
  598. 20:15go now because those beans start where
  599. 20:18that cone is it's almost impossible for
  600. 20:20it to really get stalled I guess it
  601. 20:21could stall up that cone because that
  602. 20:23initial bit needs a lot of torque but
  603. 20:25I've yet to have this one stall for me
  604. 20:27but anyway that's grinding filter at 250
  605. 20:30obviously it's going to take a little
  606. 20:34while now I'm going to hit the
  607. 20:37purge which just again goes up to
  608. 20:41400 all right now obviously there's less
  609. 20:44left over whenever it's this coarse
  610. 20:46grounds than it is with espresso but
  611. 20:49still worth flacking and puffing now
  612. 20:51what I'm going to do now is a little
  613. 20:52bougie you don't have to follow me at
  614. 20:54home but this has a lot of CHA in the
  615. 20:55coffee so I'm going to pour it out on
  616. 20:56this tray and blow the the chaff away
  617. 21:00and now look at it chaff free baby all
  618. 21:04right now to explain the burds I'll
  619. 21:06start with this flow chart that is
  620. 21:08floating around the cetch Forum that
  621. 21:10kind of describes the different burds
  622. 21:11and their intention or their intended
  623. 21:13use as they were designed they have four
  624. 21:16different birds that are offered that
  625. 21:18are built inhouse and designed by Dennis
  626. 21:20himself and these are called indd for
  627. 21:22medium dark so the shuriken medium dark
  628. 21:24you have the shuriken light medium have
  629. 21:26the shuriken coarse and the shuriken
  630. 21:29sweet so the top of the flowchart says
  631. 21:31D1 an allaround burst something that can
  632. 21:32do filter can do espresso can do dark
  633. 21:35and light kind of do everything well
  634. 21:37well if it's a yes then you do the
  635. 21:39shuriken light medium if it's a no then
  636. 21:41it asks do you want light or dark roast
  637. 21:42or like light medium or medium dark
  638. 21:44roast if you want medium dark you go
  639. 21:45with the medium dark burst if you want
  640. 21:47light medium then it asks one more
  641. 21:48question what type of ratio do you like
  642. 21:50do you want those really small RTO style
  643. 21:52shots if so get the light medium if you
  644. 21:54want the longer shots 1 to three 1 to
  645. 21:56four then get the sweet
  646. 21:59I think that is a helpful breakdown but
  647. 22:01I would like to talk a little bit more
  648. 22:02about my experience with these
  649. 22:05burs I have not been shy that the my
  650. 22:07favorite 98mm Burr for Brewing is the
  651. 22:09Brew burs from Titus or SSP uh they're
  652. 22:12they're a little different iterations
  653. 22:13but I prefer the Titus ones they're a
  654. 22:15little older geometry of a bit bigger
  655. 22:18outfall they cannot do espresso like at
  656. 22:20all but they make really really
  657. 22:21incredible tea like super complex super
  658. 22:24Nuance just delicious bruise for my
  659. 22:25palette now not everyone shares that and
  660. 22:27that's fine they also show any defect
  661. 22:28that coffee has so it's a very small
  662. 22:30window to get a really nice coffee now
  663. 22:33with the coarse bur it is not quite as
  664. 22:35intense of clarity in flavor separation
  665. 22:37as as these are to me it's not as teal
  666. 22:40like or anything like that it has the
  667. 22:41body of something like the hu at 98 mm
  668. 22:44produces but it has a lot more clarity
  669. 22:46and not as much sharp acidity as that H
  670. 22:48can kind of give you so it has a really
  671. 22:49nice presentation of acidity it's got a
  672. 22:51really rounded mouth feel it has a great
  673. 22:53aftertaste it does just a fantastic
  674. 22:56job while the pre25 15 ek43 is great but
  675. 23:00those are impossible to find they're not
  676. 23:01made anymore and they tend to have
  677. 23:03defects like some of them can be warped
  678. 23:05because how they're made the cor Spurs
  679. 23:06make filter coffee easy whether you're
  680. 23:08doing a light roast medium roast dark
  681. 23:10roast you put it in there and it does a
  682. 23:12good job now with a light medium it
  683. 23:14seems to produce a decent amount of
  684. 23:15fines something similar to what the ek43
  685. 23:18does with its stock burst that's
  686. 23:20actually the closest in taste that I can
  687. 23:21think of when I'm trying to compare this
  688. 23:23to other 98mm burs it has a big sweet
  689. 23:26spot it is a bit smoother with a bit
  690. 23:28bigger window of dialing in than the
  691. 23:30ek43 post 2015 cast B are even though
  692. 23:34the geometry is way different they're
  693. 23:35somewhat similar though I would say for
  694. 23:38the average user these are much more
  695. 23:40forgiving they give you a really nice
  696. 23:42acidity but it's not an intense acidity
  697. 23:43like the a Hu from SSP it's not as
  698. 23:46Punchy and it doesn't have that kind of
  699. 23:47harshness that you might get nowhere
  700. 23:49near as clear as hu or obviously as the
  701. 23:51Brew burst but it gives you a really
  702. 23:53nice body it gives you a nice acidity a
  703. 23:55nice texture gives you nice sweetness
  704. 23:57it's round it's an easy all round bur as
  705. 24:00far as its filter capabilities because
  706. 24:02of that fast feeding is what I'm
  707. 24:04speculating in the the extra production
  708. 24:06of fins it does give you a bit more of a
  709. 24:08murky body when it comes to the actual
  710. 24:10Brew itself it they they make good brews
  711. 24:13they're not you know Ace bruise is what
  712. 24:15I'm trying to get at they they're
  713. 24:16similar to the filtered coffees that the
  714. 24:18core burs on the Weber eg1 kind of can
  715. 24:20give you what the core is for me and the
  716. 24:2280mm world is what the LM is for me in
  717. 24:24the 98 mm world it was the ek43 bur as
  718. 24:28as far as something that was an
  719. 24:29allrounder it could do filter pretty
  720. 24:30well it could do espresso well had a
  721. 24:32nice sweet spot people wanted EK shots
  722. 24:34because you got that kind of texture and
  723. 24:37a lot of that because they're cast Birds
  724. 24:38these are not cast but I think they give
  725. 24:40you an experience similar to that with a
  726. 24:42bit better perception of the acidity not
  727. 24:45that these are higher acidity but they
  728. 24:46give you a better experience of that
  729. 24:48acidity on your palette the sweetness is
  730. 24:50maybe a bit higher in the ek43 but
  731. 24:53overall in every other area I kind of
  732. 24:54give the the the scores to the LM very
  733. 24:57flexible very easy now these are
  734. 24:59recommended to be used at really short
  735. 25:01ratios so like a 1: one a 1 to2 and then
  736. 25:04they say that over that you should get
  737. 25:05the sweet burst I've actually found that
  738. 25:07these do well above that ratio as well
  739. 25:10whereas it's fun to explore the high
  740. 25:12extraction really low yield shots
  741. 25:14they're not really my bag man and I
  742. 25:16don't think that the texture suffers too
  743. 25:18much when you extend it a lot more and
  744. 25:20in fact if you really know what you're
  745. 25:21doing you can get some decent texture
  746. 25:23past that 1: two of course that's not
  747. 25:25what they're made for but I do know that
  748. 25:27they do a great job and I know some
  749. 25:29people who swear by doing much bigger
  750. 25:31ratios even up to a 1 to7 on espresso is
  751. 25:34that espresso anymore I don't know it's
  752. 25:35more like soup if I'm wanting my high
  753. 25:38Clarity kind of soup sto shots I much
  754. 25:40prefer the hu burst from SSP or the Brew
  755. 25:43burst from SSP or the Lu bur from SSP
  756. 25:46those if I'm wanting High Clarity and
  757. 25:47intense acidity those give me more so
  758. 25:50what I'm looking for it's kind of like
  759. 25:52if you were thinking in terms of shapes
  760. 25:54you would have more of an the top of an
  761. 25:56oval so it's like almost an angle
  762. 25:58almost a complete curve you would have
  763. 26:00with the LM burs with the hu burs
  764. 26:03they're kind of more of a triangle
  765. 26:04they're really intense they're not
  766. 26:06really very forgiving it's it's like
  767. 26:08it's like you get that Punchy acidity
  768. 26:10you get that really intense Clarity you
  769. 26:12get that separation but the sweetness in
  770. 26:15the body can be kind of lacking a bit
  771. 26:16Hollow and it doesn't really extend as
  772. 26:19much whereas this one kind of has a
  773. 26:20better extending type of
  774. 26:24finish with the sweet burst what you're
  775. 26:26going to get is kind of something that
  776. 26:28SSP doesn't really have in its uh area
  777. 26:30you would think these are kind of
  778. 26:32replicating The diding Suite the diding
  779. 26:33lab sweets which a lot of people love I
  780. 26:35enjoy quite a bit and SSP has their own
  781. 26:37version of the cast the lab Suite cast
  782. 26:39which I currently have in this Max one
  783. 26:41but even with that there is almost too
  784. 26:43much of a target for acidity with them
  785. 26:46that it takes away from some of that
  786. 26:48sweetness and because all this is about
  787. 26:49perception of sweetness right we don't
  788. 26:51have enough sugar content in coffee to
  789. 26:53actually perceive of Sweetness from
  790. 26:54sugar it's more about the perception of
  791. 26:56all the different flavors playing along
  792. 26:58each other and with this Burr I'm
  793. 27:00getting incredibly sweet shots at the 1
  794. 27:03to one and a half range all the way up
  795. 27:04to like 1 to five they do an okay job
  796. 27:06with body It suffers a bit there but the
  797. 27:08sweetness is really Immaculate and it
  798. 27:10tones down some of the harsh acidity
  799. 27:11that you'll get from a lot of these SSP
  800. 27:13options which are usually my
  801. 27:16Mo doesn't really have a counterpart
  802. 27:18with SSP I guess the closest would be
  803. 27:20the cast bur but if you could tone the
  804. 27:22acidity down a bit uh and the harshness
  805. 27:24down a bit then you would have something
  806. 27:26closer to this the filter from the s W
  807. 27:28though I think is a bit better than the
  808. 27:30ones from the slm they're a bit cleaner
  809. 27:33they're not as exciting as perhaps the
  810. 27:36pre25 ek43 burs which I have right here
  811. 27:39they're not as good as the coarse burs
  812. 27:41but if you really dial in and spend a
  813. 27:42lot of time you'll be able to get
  814. 27:44something that's you know 70 maybe 80%
  815. 27:46of the way to their Co burs that I
  816. 27:48currently have housed in here they don't
  817. 27:50quite hit as much layering and
  818. 27:52complexity as I might want but they give
  819. 27:54you a nice Brew The Sweet Spot is a bit
  820. 27:56smaller for it because that's not really
  821. 27:58what they're made for and it's much
  822. 28:00bigger on the coar burs but in the end
  823. 28:02you're getting a nice filter so that's a
  824. 28:04good Dual Purpose bur in my opinion they
  825. 28:06actually have a similar inclination on
  826. 28:07the inside going to the outside to that
  827. 28:10of like the Lu 98 mm or the hu 98 mm it
  828. 28:14has a similar thickness on that initial
  829. 28:16pre- breaker as does the sweet
  830. 28:20burs so far with all the different burn
  831. 28:22manufacturers the only ones I've had
  832. 28:24really great experiences with have been
  833. 28:26hro or or diding for the most part part
  834. 28:28and SSP of course and so it's really
  835. 28:31nice to know these are out there again
  836. 28:32it's a shame they don't fit in other
  837. 28:33Grinders which again I understand
  838. 28:35because you know when it's a small
  839. 28:36company you want to kind of keep things
  840. 28:38so it can't be replicated but it they
  841. 28:41are really nice and since this is really
  842. 28:42the only grinder that can use them it
  843. 28:43kind of forces you into that ecosystem
  844. 28:45similar to how Apple does the stinking
  845. 28:47plug that can only work with Theirs
  846. 28:48Whatever I know they've switched over
  847. 28:50but for years it was like that now these
  848. 28:51birds are said to come pre-season prior
  849. 28:53to coating so you shouldn't really need
  850. 28:54to do anything they also run like half a
  851. 28:56pound through before shipping it to you
  852. 28:58and they also calibrate it and and they
  853. 28:59pull a shot and they send you this nice
  854. 29:01little sheet of
  855. 29:02paper monolith test report for Lance and
  856. 29:05so it tells you what grind setting they
  857. 29:07used what basket they used how they
  858. 29:08pulled their shot and what the
  859. 29:09extraction percentage is in order for
  860. 29:11you to kind of know that these are high-
  861. 29:13performing burd so they always want to
  862. 29:15do a really high extraction just to show
  863. 29:16that they can not necessarily that they
  864. 29:18should even though they're said they're
  865. 29:20preseason I have found that you need
  866. 29:21quite a bit of seasoning with these burs
  867. 29:23in order to lessen the static and to
  868. 29:25improve the cup profile but with the l
  869. 29:28and the ssw which was actually on a
  870. 29:30pre-used grinder I found the need to do
  871. 29:31a little bit more seasoning in it and it
  872. 29:33opened up even more all three birds that
  873. 29:35I've seen and I can only imagine the MD
  874. 29:36is similar all of them have nine pre-
  875. 29:38Breakers I know the ssw or the suite
  876. 29:40used to have six pre- Breakers and at
  877. 29:42some point they went to 12 but now
  878. 29:43they're at nine with version three and
  879. 29:45this was to improve the feed rate or the
  880. 29:47speed of the grinding they used to take
  881. 29:49like 50 seconds to grind because they
  882. 29:51only had the six pre- Breakers it took
  883. 29:53forever to slowly feed them through
  884. 29:54which was actually a designed decision
  885. 29:56in order to slowly grind the beans but
  886. 29:58the moving up to the nine pre Breakers
  887. 30:00helped improve that to like a 20 second
  888. 30:02grind so you still have a long Grind
  889. 30:03Time with these Grinders but I mean when
  890. 30:06you're doing these these expensive
  891. 30:07Grinders hopefully the number one thing
  892. 30:09in your mind is not speed uh because
  893. 30:11well you're not going to get it with
  894. 30:12this you you're better off with a p100
  895. 30:13if that's what you want but speaking of
  896. 30:15the p100 and speaking of my experience
  897. 30:17with other in-game Grinders quote
  898. 30:18unquote all of them have some flaws you
  899. 30:20have to work around and I know that's
  900. 30:21super annoying a lot of people say God
  901. 30:23I'm paying like $5,000 I shouldn't have
  902. 30:25any flaws and I understand that
  903. 30:27sentiment but the reality is all of them
  904. 30:30have their own little flaws the p100
  905. 30:32doesn't stall it doesn't stall ever it
  906. 30:34has very low retention you don't really
  907. 30:36need to use Bellows it has a much faster
  908. 30:38RPM so that when it's purging it's
  909. 30:40actually super effective the knocker is
  910. 30:42not very great but it it can get it it
  911. 30:44can get it out I prefer the taste out of
  912. 30:47this but workflow on this is honestly
  913. 30:49pretty bad I usually prefer using the
  914. 30:50eg1 when doing videos because it is the
  915. 30:53most consistent with having to faf
  916. 30:54around as far as the dial as far as the
  917. 30:56retention I can weigh in 20.05 or so
  918. 30:59using my pixa scale and exact and expect
  919. 31:01to get almost exactly 20.01 20.02 out of
  920. 31:04the grinder without having to use Bellow
  921. 31:06or anything but I've always been a huge
  922. 31:09proponent of taste over workflow some
  923. 31:11people disagree with that I don't know
  924. 31:12why you'd be buying $4,000 grinder if it
  925. 31:14wasn't for optimal taste you can get
  926. 31:16great workflows for much
  927. 31:19cheaper so in my opinion if you're
  928. 31:21buying one of these Grinders you're
  929. 31:22better off just staying in the shuriken
  930. 31:24World unless you really want to try
  931. 31:25something outside of it and I think
  932. 31:27there's built really well you can play
  933. 31:28with the acceleration you can play with
  934. 31:30the speed variable speed you have 98mm
  935. 31:32bur options you can switch the the motor
  936. 31:34and you can take out the pre- breaker in
  937. 31:36order to fit other 98mm burs in
  938. 31:39there holy cow that was a long video if
  939. 31:41you made it this far you are my favorite
  940. 31:44and there's probably like 12 of you
  941. 31:45thanks for listening hopefully you
  942. 31:47learned some things in this video not
  943. 31:48only about the monolith and what it's
  944. 31:50doing uh and some of its cons some of
  945. 31:52its
  946. 31:53pros but hopefully you picked up
  947. 31:55something new hopefully talking about
  948. 31:56the Heat or talking about particle
  949. 31:58distribution or talking about the
  950. 31:59feeding or the pre- breaker or the bird
  951. 32:01geometry anything like that hopefully
  952. 32:03that was helpful that you learned
  953. 32:04something and uh if you did you know
  954. 32:05consider hitting the like hitting the
  955. 32:07Subscribe all that helps me so much I
  956. 32:09have my Instagram my Facebook my second
  957. 32:10YouTube all down below usual pandering
  958. 32:12stuff uh but that's about it for today
  959. 32:16so without further Ado I hope that you
  960. 32:19brew something tasty today and cheers

About this transcript

This page contains the full transcript of What Does a $3600 Grinder Offer?: Kafatek Monolith Max 2 Review and Burr Chat by Lance Hedrick, generated from the public captions YouTube serves with the video. The transcript has 7,173 words across 960 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.