YouTube2Text

TURNING THIS DAMAGED A3 INTO SOMETHING SPECIAL — Transcript

by Liam Betts · 4,478 words · 612 segments · language en · Watch on YouTube

Full transcript

  1. 0:00In the last video, I picked up this
  2. 0:01crash damaged Audi A3 2 L TDI S-line,
  3. 0:05but it has some major issues. An
  4. 0:07absolute ton of smoke was coming out of
  5. 0:09the exhaust. We had an engine light, an
  6. 0:11airbag light, a glow plug light, and a
  7. 0:13bunch of other faults on the dash. And
  8. 0:15not to mention, the whole front end is
  9. 0:17absolutely smashed up on this car. But
  10. 0:19after diagnosing the car and finding out
  11. 0:21that it had a faulty EGR cooler, I
  12. 0:24bought a brand new one, replaced it, and
  13. 0:26now the car isn't drinking all of its
  14. 0:28coolant. And now it's my job to get the
  15. 0:30rest of this car finished and sorted so
  16. 0:32I can take it for a nice long drive up
  17. 0:34to the Peak District. Before we continue
  18. 0:37diagnosing this car, I need to swap that
  19. 0:39battery out. And I've got a brand new
  20. 0:41Bosch battery right here. So, let's get
  21. 0:42that swapped out. So, all I need to do
  22. 0:44is remove the negative terminal, lift
  23. 0:46that battery up and out. Grab the brand
  24. 0:48new battery and drop that straight into
  25. 0:50place. And then we can connect the
  26. 0:52positive and the negative terminals and
  27. 0:53tighten them up with a 10m. After last
  28. 0:55week's video, I did take this car for a
  29. 0:5840minute drive out at nighttime just
  30. 1:00because of obviously how much this car
  31. 1:02was actually smoking. And I have got it
  32. 1:04to a point where it doesn't smoke
  33. 1:06anymore. So if we jump in the car,
  34. 1:08[sighs]
  35. 1:09turn the ignition on and give the car a
  36. 1:12start.
  37. 1:15There we go. So we are jumping a little
  38. 1:17bit just because this car does need a
  39. 1:19new glow plug in cylinder 1 and cylinder
  40. 1:224. But right now, if we come to the back
  41. 1:25of the car, we're literally getting
  42. 1:28absolutely no smoke coming out. And
  43. 1:30we're also not getting any more water
  44. 1:31come out of the exhaust, which is great.
  45. 1:33So, no messing around. Let's pull the
  46. 1:35launch diagnostics out and diagnose this
  47. 1:37car and see what is going on. We have
  48. 1:40cylinder one glow plug circuit, and we
  49. 1:42also have cylinder 4 glow plug circuit.
  50. 1:44So, I've ordered two new glow plugs for
  51. 1:47this engine, so hopefully the startup
  52. 1:49will be a little bit better. And then we
  53. 1:51also have an O2 sensor heater control
  54. 1:53circuit bank one sensor 2. So what I
  55. 1:57need to do is I need to buy a brand new
  56. 1:58O2 sensor to fit because supposedly that
  57. 2:02one is absolutely dead. And then in the
  58. 2:04climate control we have refrigerant
  59. 2:07pressure too low or lower limit not
  60. 2:09reached. Um which I'm going to check
  61. 2:11that out once I start taking off the
  62. 2:13front end. And we also have fresh air
  63. 2:15recirculation airflow flap motor
  64. 2:18actuator jammed. So, I need to check
  65. 2:20that out as well. So, the first thing we
  66. 2:22need to do is remove the windscreen
  67. 2:24wipers because we can't get the scuttle
  68. 2:26panel off without the windscreen wipers
  69. 2:28out the way. And to remove these wiper
  70. 2:29blades, I'm just using a ball joint
  71. 2:31splitter cuz I don't actually have a
  72. 2:32proper windscreen wiper puller.
  73. 2:34[laughter]
  74. 2:35And after a little bit of a cleanup, we
  75. 2:37now have this little casing off here,
  76. 2:39which reveals this fresh air flap vent.
  77. 2:43So, now I think all we have is three 10
  78. 2:46mil nuts. And then we can take that off
  79. 2:48and we can see if we can actually get to
  80. 2:50the flap motor. And there we go. So,
  81. 2:53it's finally fixed. So, now all I did is
  82. 2:56I moved this flap cuz this flap was
  83. 2:58stuck right here. So, if we go into the
  84. 3:01basic settings and do an adjust
  85. 3:04that now closes
  86. 3:08and then it opens again. There we go.
  87. 3:10So, now we have it's absolutely fine.
  88. 3:13And I just got to wait for it to finish.
  89. 3:16And there we go. Finished correctly.
  90. 3:18We're on to a win here. So now that is
  91. 3:20fixed and the fans are blown really,
  92. 3:22really nicely. I've just checked the
  93. 3:25passenger side vent over here and the
  94. 3:27driver side vent far end because
  95. 3:30basically we're not getting very hot air
  96. 3:32come through. It's it's warm, but it's
  97. 3:34not hot. And this driver side one right
  98. 3:37here is warm, but the passenger side one
  99. 3:40is cold. So I think what we have is we
  100. 3:43have a blocked heater matrix. So, I'm
  101. 3:45going to have to get a new heater matrix
  102. 3:47as well. Strip this down and then
  103. 3:50obviously swap out the heater matrix as
  104. 3:52well. But for now, we can start putting
  105. 3:54all the scuttle back on and then we can
  106. 3:55start diagnosing the next problem. Okay,
  107. 3:57scuttle is all back on. Window wipers,
  108. 4:00blades are all back on. Uh, the next
  109. 4:02code that I need to well needed to have
  110. 4:05a look at was a DPF pressure sensor
  111. 4:08code. And I know that these
  112. 4:12sensors right here are for the DPF
  113. 4:14because these pipes go down into the
  114. 4:16side of the DPF. I was having a little
  115. 4:18look at this just to, you know, make
  116. 4:20sure that the electrical connectors were
  117. 4:22all okay. And the next thing you want to
  118. 4:25check is the hose and I went to just
  119. 4:28like see if there's any rips in the hose
  120. 4:30and
  121. 4:32the whole thing has just snapped off. So
  122. 4:35that's a nice easy simple fix. I've
  123. 4:37ordered a new one of these which is like
  124. 4:3910 quid off eBay. So, um it's it's VW.
  125. 4:43It's exactly the same part number. Um
  126. 4:46so, that's all good. I'll just wait for
  127. 4:47a new one of those to come. I'll have to
  128. 4:49get that little plastic bit out of the
  129. 4:51hose. Uh and then install the new one
  130. 4:55and hopefully that's all good. So the
  131. 4:56next code that I'm cautious about um
  132. 4:59because obviously the car is in a slight
  133. 5:01limp mode. This O2 sensor heater control
  134. 5:04oops O2 sensor heater control circuit
  135. 5:08bank one sensor 2. So that is the next
  136. 5:11issue that we're having. The car is
  137. 5:13obviously driving nicely, but there's
  138. 5:15literally no power in the turbo at all.
  139. 5:18And [clears throat] I believe if we look
  140. 5:20down the back here, we have a sensor
  141. 5:22which is right there which has a gray
  142. 5:25cable uh or gray wire sorry going from
  143. 5:28it. Uh and that is post catalytic
  144. 5:31converter. The fact that the heating
  145. 5:33element has gone in it I think because
  146. 5:35all of the coolant from the EGR cooler
  147. 5:37when the old one was on there obviously
  148. 5:39coolant is going through the exhaust and
  149. 5:41as soon as any coolant touches that it's
  150. 5:44just going to burn the heater out. And
  151. 5:46while we're underneath, we've got an
  152. 5:48absolutely soaked sump once again. So, I
  153. 5:52think, as you can see from here,
  154. 5:56I don't know if it's leaking directly
  155. 5:57from the sump or whether it's leaking
  156. 5:59from the front main seal. So, what I
  157. 6:01need to do is take the wheel off, take
  158. 6:02the arch liner out, and then we can take
  159. 6:04the pulley off and see if we need a
  160. 6:05front main seal, see if we need to
  161. 6:07literally just take the sump off and
  162. 6:09reseal the sump or where this oil leak
  163. 6:11is coming from. Because this oil leak is
  164. 6:13absolutely savage. I literally cleaned
  165. 6:14this up before I went for a drive and
  166. 6:16now it's absolutely chucking it out
  167. 6:18again. So, that's definitely something
  168. 6:21we need to address. Okay, arch lining
  169. 6:24off. I think I'm going to need a
  170. 6:25replacement one of those cuz of
  171. 6:26obviously the crash on this side. Um,
  172. 6:29that's pretty much mashed a lot of this
  173. 6:30up. But, don't you love it when you're
  174. 6:33taking something apart and you find a
  175. 6:35nice free tool, a Blueoint T40 Torx.
  176. 6:39Perfect. All right, I think I found our
  177. 6:41issue. So, this is absolutely soaked.
  178. 6:45And I can literally see a gap between
  179. 6:47the sump and front main seal. So, I'm
  180. 6:51gonna have to give this a bit of a clean
  181. 6:52up and then I'm going to do an engine
  182. 6:55flush and then I will take off the sump
  183. 6:57after I've drained all of the oil and
  184. 6:59reseal that. Whoever's done this has
  185. 7:01clearly not done a good enough job. At
  186. 7:03least that's confirmed and I don't have
  187. 7:05to do a front main seal. All right. So,
  188. 7:07I'm just warming the engine up and then
  189. 7:09I'm going to put some engine flush in so
  190. 7:11we can drop all of the oil out of the
  191. 7:13engine. We can give the engine a nice
  192. 7:15complete clean out and then we can take
  193. 7:17the sump off so we can fix that oil
  194. 7:18leak. Let's get this engine flush into
  195. 7:21the engine.
  196. 7:26Right, whole engine flush in. Let's
  197. 7:29start the engine and run it for 15
  198. 7:31minutes.
  199. 7:49Okay, so with all of the sump bolts out,
  200. 7:52I now should be able to just pry it
  201. 7:55open. Give me a second.
  202. 8:00Okie dokie. Yeah, there you go.
  203. 8:05Don't spill the rest of the oil.
  204. 8:09I've completely cleaned the sump up.
  205. 8:11That's looking absolutely beautiful.
  206. 8:13Cleaned it out. Blow it out with
  207. 8:14compressed air. And then underneath,
  208. 8:16I've also completely cleaned the bottom
  209. 8:18of the block. Everything is looking all
  210. 8:21good. And the surface area or the mating
  211. 8:23area is nice and clean. Everything looks
  212. 8:26great under here. So, I'm happy with
  213. 8:28that. Um, I'm really focusing on this,
  214. 8:31um, front main seal area. Uh, I don't
  215. 8:34want to take too much of this sealant
  216. 8:36off just because that is what holds the
  217. 8:38actual seal into there. But I'm going to
  218. 8:40make sure that I put plenty of sealant
  219. 8:42on around that area cuz I don't want
  220. 8:43that leaking again. And also, it's very
  221. 8:46key that you clean your surface, your
  222. 8:48mating surface, because if you've got
  223. 8:51any oil, you will get more oil leaks as
  224. 8:53soon as you put your sump back on.
  225. 9:06Okay, cool. All right, so that's
  226. 9:08everything
  227. 9:10um
  228. 9:12torqued up.
  229. 9:14Everything's tight.
  230. 9:17Now, we let it sit for 24 hours
  231. 9:21and then I'll put some oil in it and
  232. 9:23we'll [clears throat] see how we get on.
  233. 9:25So, I'm just in the middle of my routine
  234. 9:285,000mi oil change on my [music] Audi A5
  235. 9:303 L V6. But not only do I like to keep
  236. 9:33my engine maintained and [music]
  237. 9:35healthy,
  238. 9:37I also like to keep the interior feeling
  239. 9:39clean and smelling fresh. And that's
  240. 9:42where Flavor has come in clutch. They
  241. 9:43were kind enough to send me out their
  242. 9:45[music] bundle kit, which comes with a
  243. 9:47turbo can, a wood diffuser, an oda
  244. 9:49perfume, and a little scratch and sniff.
  245. 9:51They have a bunch of different designer
  246. 9:53fragrance inspired [music] products
  247. 9:54which are going to keep your car
  248. 9:56smelling absolutely wonderful. And
  249. 9:57they've been kind enough to send me out
  250. 9:59the [music] Creed version of their
  251. 10:01bundle. So, let's crack some of these
  252. 10:02open together. I've already used the
  253. 10:04Turbo Can. The Turbo Can [music] is
  254. 10:05absolutely insane. Look how much this
  255. 10:07sprays.
  256. 10:10Oh my god. [laughter]
  257. 10:12And it smells absolutely lovely. Just
  258. 10:14spraying the can that many times is
  259. 10:16going to keep this car smelling
  260. 10:17absolutely lovely for days. [music] And
  261. 10:18here we have the O perfume.
  262. 10:22Oh, that smells absolutely insane. That
  263. 10:25is absolutely beautiful. [music] And
  264. 10:26then we've got the wood diffuser.
  265. 10:29I think what I'm going to do with this
  266. 10:30is I'm going to set it up in [music] the
  267. 10:33A3 just to keep that smelling absolutely
  268. 10:35lovely as well. And there's the little
  269. 10:37wood diffuser. And there's a hole in
  270. 10:39this side which you can put the string
  271. 10:40[music] through and then you can hang it
  272. 10:42anywhere you want. And if you don't want
  273. 10:43to do that, you also get a clip [music]
  274. 10:45which you can put into the lid and then
  275. 10:48screw the lid back on and then you can
  276. 10:49slot it straight into one of your vents.
  277. 10:52I'm going to [music] crack the scratch
  278. 10:53and sniff open to leave in my car
  279. 10:55because I absolutely love this scent.
  280. 10:57There we go. Oh, I wish you could smell
  281. 10:59this. That's like uh that's like almost
  282. 11:02coconuty [music] with a scent of Creed.
  283. 11:05That will sit in the cup holder and that
  284. 11:07will make my car smell absolutely
  285. 11:08fantastic every single time I get in my
  286. 11:11car. flavor reached out to me saying,
  287. 11:12"Do I want to try them?" And I said,
  288. 11:14"Absolutely." And a few days later, I
  289. 11:16went to one of my local garages to fill
  290. 11:18up fuel, and I saw they [music] had a
  291. 11:19stall in the shop. So, if you don't want
  292. 11:21to pick one of these up via the video,
  293. 11:22make sure to go into your local garages
  294. 11:24and other stores around the UK, and
  295. 11:26there'll be plenty of flavor for [music]
  296. 11:28your car. But, if you did want to pick
  297. 11:29some up right now and make your car
  298. 11:31smell fresh immediately, I'll leave the
  299. 11:33link in the description, and I'll leave
  300. 11:34my discount code on screen now so you
  301. 11:36can save yourself a bit of cash and make
  302. 11:37your car smell absolutely fantastic.
  303. 11:39Thanks so much, Flavor, for sponsoring
  304. 11:41today's video. Now, let's get back to
  305. 11:43the A3. The next thing I need to do is
  306. 11:46replace the front and rear pads and
  307. 11:47discs, cuz they've seen better days.
  308. 11:49You've seen me replace pads and discs
  309. 11:51plenty of times before, but I want these
  310. 11:53pads and discs to be absolutely perfect
  311. 11:55for the new owner. So, all I'm doing
  312. 11:57here is putting some copper grease onto
  313. 11:58the hub, and we can put the disc on, put
  314. 12:00the caliper carrier back on, and put the
  315. 12:01caliper back on with the new pads.
  316. 12:05So, my new rear Febby uh wheel bearing
  317. 12:09has just been delivered. So, I've been
  318. 12:11waiting to get the wheel bearing on
  319. 12:13before I do the rear discs, just because
  320. 12:16it saves doing the job all over again.
  321. 12:18So, let's get that wheel off, replace
  322. 12:19that wheel bearing, and replace the
  323. 12:21discs. And there we go. So, after way
  324. 12:23too long putting just these discs and
  325. 12:25pads on, I need still need to tighten
  326. 12:28that up. But, I'm going to do the other
  327. 12:29side first, and then I'll put the
  328. 12:31handbrake on, and then I'll tighten this
  329. 12:32up. The next thing to tick off the list
  330. 12:35on this car is a brand new O2 sensor.
  331. 12:38£95
  332. 12:40for an O2 sensor. And that's the new O2
  333. 12:42sensor installed onto the car. That was
  334. 12:45actually really quite difficult. Um, the
  335. 12:47best way that I found to do that was to
  336. 12:49put the actual O2 sensor socket on from
  337. 12:52the top, put the ratchet on from the
  338. 12:54top, and then go underneath and undo it
  339. 12:56from the bottom. If you're doing that on
  340. 12:59the floor, which I would have been doing
  341. 13:00that on the floor probably six uh three
  342. 13:03months ago, and I'm glad I'm not now
  343. 13:05because at least I have the pit and I
  344. 13:07can stand underneath the car. But if
  345. 13:10you're doing that on the floor, good
  346. 13:11luck because that was quite difficult
  347. 13:13standing up, let alone being dead on the
  348. 13:16floor. So, it's finally time to start
  349. 13:18stripping the old bumper off of this car
  350. 13:20so we can put the new one on. But before
  351. 13:23we do that, let me show you what we've
  352. 13:25got.
  353. 13:26>> [music]
  354. 13:27>> Got to let it off. Let it off.
  355. 13:32I go
  356. 13:35[music] a lot to
  357. 13:38let it off. Let it off.
  358. 13:43I think this front bumper is going to
  359. 13:45completely change the way that this car
  360. 13:46looks. I think this car looks absolutely
  361. 13:48lovely anyway, but with this front
  362. 13:50bumper on that car, it's going to look
  363. 13:53absolutely nuts. I've never fitted a
  364. 13:55aftermarket bumper to a car before, so
  365. 13:58I'm hoping that I don't have to do much
  366. 13:59modification to be able to get it to fit
  367. 14:02onto the car. Obviously, I know I'm
  368. 14:04dealing with a crash damaged car, so I
  369. 14:06may have some broken brackets or
  370. 14:08anything like that. So, let's strip this
  371. 14:10one off and see where we're at bracket
  372. 14:12wise. Amazing. So, the front bumper is
  373. 14:15off and in pieces. [laughter]
  374. 14:18I've actually taken off the fog lights
  375. 14:20and I've also got one fog light surround
  376. 14:22which is right there which I can
  377. 14:24actually salvage from this bumper and
  378. 14:26maybe sell because they're in good
  379. 14:28condition. So, we've actually been
  380. 14:31really really lucky with all of the
  381. 14:32brackets here. Um, this bracket has
  382. 14:34snapped off of the bumper, but there's
  383. 14:37literally a bolt behind here which I can
  384. 14:39just take that bolt out and then that's
  385. 14:41absolutely fine. This bracket here looks
  386. 14:45okay. it. I reckon I can probably
  387. 14:47salvage it. Um, that looks fine. The CR
  388. 14:50slam panel and all of the front end
  389. 14:53looks absolutely fine. All of the
  390. 14:54brackets on the headlights look fine.
  391. 14:56And then if we move over to the other
  392. 14:58side, same again. This little um bracket
  393. 15:01is snapped here. But again, it's just a
  394. 15:03bolt on that side. Uh, this slam panel
  395. 15:05here looks fine. Um, all this looks
  396. 15:09okay. Everything looks fine. And I'm
  397. 15:11even in luck. The wiring all looks
  398. 15:15absolutely fine as well. So, I think
  399. 15:17we're really on to a win here. All
  400. 15:19right. So, to get the front wing off,
  401. 15:21we've got a few little bolts on the
  402. 15:23front here. So, we got one here, one
  403. 15:25here, and I believe there's one under
  404. 15:27here. And then we've also got a few
  405. 15:29inside the door. But I think what I'm
  406. 15:32going to have to do, there's two little
  407. 15:34clips. There's one there, and then
  408. 15:36there's one just down there. Um, but
  409. 15:39then you've got to take that whole trim
  410. 15:40panel out. And I think the only way I'm
  411. 15:43going to be able to do that is by taking
  412. 15:45the door off. So, let's get the door
  413. 15:47off. And then we can get that wing off.
  414. 15:52There we go. And that gives us access.
  415. 15:58No, it doesn't. Oh, yeah. Now, there's
  416. 16:00one here and then there's two the other
  417. 16:03way. Okay. So, we need to jack the wheel
  418. 16:06up and
  419. 16:10come [clears throat] in from the other
  420. 16:11side. Ah, what a pain. Anyway, I don't
  421. 16:15think I could have maybe I could have
  422. 16:17got to that one without taking the door
  423. 16:19off. [laughter]
  424. 16:21Oh well, you live and you learn. And
  425. 16:23with all of the bolts out, that's the
  426. 16:25wing off. So, that was the first time
  427. 16:26that I've ever taken a door off and also
  428. 16:29a wing. So, I'm sure there's probably
  429. 16:31plenty of people in the comments that's
  430. 16:33going to be like, "Oh, you don't even
  431. 16:34know how to take a door off and you've
  432. 16:35rebuilt engine XY Z." But, you know, it
  433. 16:38is what it is. I've not I've never had a
  434. 16:41space to be able to do this kind of
  435. 16:42work. So, um you know, I don't really
  436. 16:45want to be taking a door off when it's
  437. 16:47outside cuz I live in the UK and if I
  438. 16:50take a door off and then it starts
  439. 16:51chucking it down, I'm stuffed. I you
  440. 16:53know, I've never done it before. So,
  441. 16:55obviously now I've got some experience
  442. 16:58actually taking panels off, which is
  443. 17:00cool. It's fun to finally start doing,
  444. 17:04and I'm sure you can tell I'm a little
  445. 17:06bit OCD, so I'm literally cleaning parts
  446. 17:08that you literally can't see. [laughter]
  447. 17:11Okay, after a bit of struggling, I've
  448. 17:12got that one out. The new one is just
  449. 17:15here. So, let's get that one back in.
  450. 17:18Um,
  451. 17:19I tried to do it without removing the
  452. 17:21whole center console because my mate
  453. 17:24said you can do it, but oh my god, that
  454. 17:26was difficult. You've literally got to
  455. 17:27bend this whole thing back like 90° to
  456. 17:30be able to get it off. And after a lot
  457. 17:32of struggling, the glove box is back in.
  458. 17:35The heater new heater matrix is in. So,
  459. 17:37when we fill the coolant back up, we
  460. 17:39should have nice warm fans. We've got
  461. 17:41the new heater matrix installed. The
  462. 17:43next thing I need to do is two rear
  463. 17:45shocks because every time you drive over
  464. 17:47a bump, the back is just kind of going
  465. 17:49D. So that's one shock done. And that's
  466. 17:51the other shock replaced. Two brand new
  467. 17:53Bosch glow plugs. Cylinder one, old one
  468. 17:57out. Brand new one back in. Cylinder
  469. 18:00number four glow plug. Brand new glow
  470. 18:01plug. Straight back in. Cylinder 4. I've
  471. 18:04just driven 2 hours from Norwich to
  472. 18:07Peter Burough and back to Norwich again
  473. 18:09to pick up this S-line wing because that
  474. 18:11one there just really didn't cut it. So,
  475. 18:13I did have to pay a bit more for this
  476. 18:14one, but at the end of the day, it's
  477. 18:16original and that's going to make this
  478. 18:18look so much better. So, I'm going to
  479. 18:19put you on a time lapse and then we'll
  480. 18:21get the the new wing back on. We'll put
  481. 18:23the door back on and then we can shut
  482. 18:24the bonnet and we can wrap everything in
  483. 18:27this uh pre-taped dust sheet roll. I'm
  484. 18:30literally going to cover most of the
  485. 18:32workshop cuz what I'm going to do is I'm
  486. 18:33going to be painting right here. So, um
  487. 18:36yeah, I don't want anything to be
  488. 18:38covered in paint. Um so, yeah, let's
  489. 18:41crack on. So, like I said, I've never
  490. 18:43actually taken a wing off of a car, let
  491. 18:45alone put one back on. And I know that a
  492. 18:48lot of people say they're quite
  493. 18:49difficult to get the panel gaps to be
  494. 18:51absolutely perfect. So, I'm really
  495. 18:53hoping that this is going to be
  496. 18:55absolutely fine when I put it back
  497. 18:56together. Obviously, if a little bit of
  498. 18:58adjustment is needed, then is what it
  499. 19:00is. Well, that was really not bad at
  500. 19:02all. Considering I've never taken a door
  501. 19:04off or a wing off, I literally didn't
  502. 19:06even have to readjust this wing. I think
  503. 19:08the uh the panel gap all the way down is
  504. 19:11pretty consistent and it's exactly the
  505. 19:14same as on the other side. I have gone
  506. 19:15over the other side and just checked,
  507. 19:17but this is all pretty much perfect. The
  508. 19:19only thing I can see is there is a
  509. 19:20slight little dent in this wing right
  510. 19:23here. So, it does kind of like bend in a
  511. 19:25little bit, but that's kind of it is
  512. 19:28what it is. Um the wing is in much
  513. 19:30better condition than you know what the
  514. 19:32last one was. So, yeah, happy with that.
  515. 19:36The only thing I have seen is under here
  516. 19:39the bracket where which is behind the
  517. 19:42wing. Uh obviously because the impact is
  518. 19:44shunted this a little bit. The the
  519. 19:47bracket that holds the headlight is is
  520. 19:49moved slightly. So what I'll have to do
  521. 19:51is I'll have to just manipulate it a
  522. 19:54bit, bend it backwards. Um and then
  523. 19:57hopefully we can get all of these bolts
  524. 19:58back in here and then we can pretty much
  525. 20:01get ready to put the bumper on. And it's
  526. 20:03the next morning. I have got my painting
  527. 20:05booth set up and ready to go. This is my
  528. 20:08makeshift painting booth. I'm literally
  529. 20:10hanging it from the ceiling. [laughter]
  530. 20:13I just need to put all of the dust cover
  531. 20:16down off of the wall so I can cover all
  532. 20:18of this up. And then I've got my air
  533. 20:20compressor, the gun, and all of the
  534. 20:22paint pretty much ready to go. I need to
  535. 20:24just go over to the mixing table and mix
  536. 20:26it. I've also got a heater blowing just
  537. 20:28to keep the the whole garage nice and
  538. 20:31warm. So, give me a few minutes. I'll
  539. 20:32pull all of this down. We'll get the
  540. 20:34compressor all compressed and then we'll
  541. 20:36start painting. There's quite a
  542. 20:37recurring theme going on in this video.
  543. 20:39I'm doing a lot of things for the first
  544. 20:41time ever, but painting is definitely
  545. 20:43something that I want to improve on. I'm
  546. 20:45really trying to break boundaries for
  547. 20:47what's possible from a random guy in a
  548. 20:50small little garage in a tiny little
  549. 20:52city. All right, so that's the painting
  550. 20:54done on the front bumper. I'm pretty
  551. 20:56happy with it considering this is my
  552. 20:58first time alone doing painting
  553. 21:01anything. Um, especially with like a
  554. 21:03proper paint gun. Um, obviously I had
  555. 21:06Steve in the background in spirit
  556. 21:08helping me out with this painting, so he
  557. 21:11definitely helped me out a lot,
  558. 21:12[laughter]
  559. 21:13but yeah, I'm I'm pretty happy with it
  560. 21:15to be honest with you. Like there is a
  561. 21:17bit of a sort of orangey peel. Um, I
  562. 21:20don't think the atomization of the
  563. 21:22lacquer was absolutely perfect or maybe
  564. 21:24the gun setup wasn't absolutely perfect,
  565. 21:27but to be completely honest with you,
  566. 21:29um, for my first time alone, I'm pretty
  567. 21:32happy with it and the color is is
  568. 21:34absolutely bang on. Tomorrow I'm going
  569. 21:36to build this up. I'm going to put the
  570. 21:38the whole front bumper back to, you
  571. 21:40know, all together. I'm going to put it
  572. 21:41on the car and then on the weekend I am
  573. 21:45driving up to the Peak District. So,
  574. 21:47we're going to test this car out and see
  575. 21:49if it's, you know, if everything is
  576. 21:50absolutely fine. And then next week, I'm
  577. 21:53going to have to sand the bumper down
  578. 21:56with a 2K, 2.5K, 3K sandpaper. And then
  579. 22:00I'll give it a polish. And hopefully, we
  580. 22:01can get rid of all of that orange peely
  581. 22:03looking stuff. And uh yeah, we're all
  582. 22:06good. So, I'll see you tomorrow when I
  583. 22:08build this bumper back up, put it on the
  584. 22:10car, and see how we look. All right, so
  585. 22:13it's the next day. The paint is
  586. 22:15completely dry now. So, that is
  587. 22:17absolutely amazing. I'm now going to
  588. 22:18start building this bumper up and then
  589. 22:20we can get it back onto the car. And
  590. 22:22finally, we can see what this bumper is
  591. 22:24going to look like on this car.
  592. 22:28[music]
  593. 22:33[music]
  594. 22:38[music]
  595. 22:43And there we go. That is the A3 nearly
  596. 22:46complete anyway. There's still a few
  597. 22:47little bits that I need to do on this
  598. 22:48car. Like the bumper isn't fully held
  599. 22:51together. This little trim down here
  600. 22:53isn't quite held on properly, but
  601. 22:56they're going to send me out a new one.
  602. 22:57So hopefully that's going to fix the
  603. 22:58issue. I've also still got got to fix
  604. 23:00the bonnet because the bonnet I just
  605. 23:02didn't get time to be able to fix it.
  606. 23:04But we've got no engine lights and
  607. 23:06everything seems absolutely sweet with
  608. 23:07the engine. So that's an absolute win.
  609. 23:09If you have enjoyed today's video,
  610. 23:10please make sure to leave a like, hit
  611. 23:12the subscribe button, and I'll catch you
  612. 23:13in the next video.

About this transcript

This page contains the full transcript of TURNING THIS DAMAGED A3 INTO SOMETHING SPECIAL by Liam Betts, generated from the public captions YouTube serves with the video. The transcript has 4,478 words across 612 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.