Thermodynamics - 3-7 Ideal Gas Equation with compressibility factor example 1 — Transcript
Full transcript
- 0:00okay so let's look at some problems
- 0:02where we're using
- 0:03not only the ideal gas law but the ideal
- 0:04gas law with the compressibility factor
- 0:07to solve for something and we're just
- 0:09going to be talking about solving for
- 0:10specific
- 0:11volume all right so let's determine the
- 0:14specific volume of refrigerant 134a
- 0:16at one mpa and 50 degrees c using the
- 0:19ideal gas equation
- 0:21or b using the generalized
- 0:22compressibility chart
- 0:24with the iowa gas equation and compare
- 0:26the values
- 0:27obtained to the actual value of 0.021796
- 0:32and so we could get this from the
- 0:34property tables the property tables
- 0:36if we have property tables are the most
- 0:38accurate
- 0:40but if we don't and maybe we can assume
- 0:42an ideal gas then pv equals rt
- 0:45might be appropriate or if we can use
- 0:47the compressibility factor to compress
- 0:49to correct the ideal gas equation pv
- 0:51equals zrt
- 0:53all right so so that's actual value and
- 0:56we want to determine the error so
- 0:58let's just use the ideal gas equation
- 1:02the pressure is 1 mpa if you don't mind
- 1:05i'm going to do 1000
- 1:06kpa right mpa
- 1:09is a thousand times larger than kpa so a
- 1:12thousand kpa
- 1:14times specific volume that's what we're
- 1:16looking for r
- 1:17the r for refrigerant 134a
- 1:20is in table a1 the r
- 1:24would be i've got .08149
- 1:28and instead of using um kilojoule
- 1:31i'm using kpa meter
- 1:34cubed per kilogram k let's
- 1:38we we can go look at that real quick the
- 1:40property tables
- 1:41table a1 if we're in si units
- 1:45the r for refrigerant all right that one
- 1:48is right here you see that
- 1:50tetrafluoride fluorethane r134a
- 1:55that is the refrigerant that's in our
- 1:56property tables that's when we say r134a
- 1:58that's what we've got
- 1:59so 0.08149 instead of using kilojoules
- 2:03per kilogram k
- 2:04i'm using kpa meter cube per kilogram k
- 2:07because they
- 2:08are the same units
- 2:12there we go and the temperature 50 i
- 2:14can't just plug in 50
- 2:16canna no no no 323 right
- 2:19add you're going to do 203.15 if you
- 2:23want
- 2:23add 273. all right so the specific
- 2:26volume would be 0.026325
- 2:30meters cubed per kilogram um how does
- 2:34that compare what is the error
- 2:36right here so the error would be
- 2:390.026325 minus the actual 0.021796
- 2:44over the actual always divide it by the
- 2:48actual
- 2:50if we kind of want to get the percent
- 2:52error
- 2:53right we don't want just the change the
- 2:55difference we want the percent
- 2:56difference so divided by the actual
- 3:000.207 that's 20.7 percent that's a
- 3:04i don't know what you think about that i
- 3:05think that's pretty big error
- 3:07but i i was assuming it's an ideal gas
- 3:11maybe it's not quite an out of the gas
- 3:12or maybe
- 3:13i can use the compressibility factor to
- 3:16correct that a little bit better
- 3:18i can say pv equals z
- 3:22rt but what is z
- 3:25what is z i can get z
- 3:29by taking the pr and the t are
- 3:32so let's kind of come down here and make
- 3:34a side note the p
- 3:35r is p over p critical
- 3:38the t r is t over t
- 3:41critical so the pressure of 1 000
- 3:45kpa over p critical that's table a1
- 3:49that's table a1 the critical point
- 3:51properties
- 3:53for r134a
- 3:56the pressure is 4.090
- 4:00mpa maybe i should have kept it in mpa
- 4:03um
- 4:044.059 and the temperature
- 4:07is 374.2
- 4:10kelvin 374.2 kelvin
- 4:14so let's go here so this is 4059
- 4:18kpa i could have just left those as npa
- 4:20one over
- 4:224.059 0.246
- 4:27is pr the temperature is 323
- 4:32over 374 0.2
- 4:360.863 is t
- 4:39r all right so
- 4:42i'm going to take those two values to
- 4:44tab to chart
- 4:45the compressibility chart a15 and read
- 4:48off the z value now let's be very very
- 4:50careful and make sure you're looking at
- 4:52the right
- 4:54lines make sure you're looking at the
- 4:55right lines okay
- 4:58so i've got a pr 0.246 tr of 0.843 let's
- 5:03go to the
- 5:04property tables let's go to
- 5:07let me kind of memorize what page this
- 5:09is on page 26 in mind
- 5:13let me try to erase you know everything
- 5:16that i had
- 5:17been doing if you've got this electronic
- 5:20copy you can
- 5:21write you know electronically over it
- 5:24and erase it uh but be careful get get a
- 5:27ruler
- 5:28you know get a ruler and make sure
- 5:30you're you're looking at
- 5:32the right x-axis the right line
- 5:35and x right line and y all right so here
- 5:37we go i've got a
- 5:39p r of 0.246
- 5:42so down here i've got 0.246 now i'm not
- 5:45going to look at this bottom one because
- 5:480.246 is very uh um
- 5:52very small but here this this top one is
- 5:55zoomed in so i can look at point two
- 5:57four six point two
- 5:58four six all right so point two point
- 6:00three there are ten
- 6:02lines between the two so point two four
- 6:070.24 would be
- 6:10one two three right here and point two
- 6:14five would be right here so in between
- 6:17those two
- 6:19and you have to estimate a little bit
- 6:20but you can make some good estimations
- 6:23in between these two is where i'm
- 6:25looking so
- 6:26one here we are one two
- 6:30one two three four in between these two
- 6:33lines
- 6:34is where i'm looking so maybe even kind
- 6:36of draw all those all the way up
- 6:38in between those two lines all right
- 6:40mitr
- 6:44was 0.863 0.863 so
- 6:49i don't have point a line for 0.863
- 6:52i've got to estimate a little bit
- 6:56make a good guess well it's going to be
- 7:00between here you know point eight
- 7:03six point eight seven point eight nine
- 7:05and then we get to point nine
- 7:06oh so maybe a little bit closer to the
- 7:09point eight
- 7:10three than the point nine line all right
- 7:13and so i'm gonna oops
- 7:16i'm gonna guess that that line would be
- 7:20i don't know maybe right here and i'm
- 7:23looking
- 7:24in between these two
- 7:27so i'm looking right about
- 7:31here right about there
- 7:35all right i'd probably give you from
- 7:380.82 to 0.86
- 7:42but i don't it really depends on on
- 7:44every problem if
- 7:45if you have to be looking between the
- 7:48correct lines
- 7:50you know you have to be looking between
- 7:51the correct lines
- 7:53in the in a good area i've got
- 7:56.84 i've got
- 8:000.84
- 8:03all right maybe you have 0.85 maybe you
- 8:05had 0.83
- 8:07i've got 0.84 as my
- 8:10z value for this problem so let's look
- 8:13at
- 8:14our notes so from those
- 8:17z is about 0.84
- 8:21so now i can use pv equals e rtp
- 8:25100 or a thousand kpa
- 8:28v is what i'm looking for equals 0.84
- 8:32times 0.08149
- 8:35323. yes you can
- 8:39um let's see take the
- 8:42if you if the this is the exact same
- 8:44equation
- 8:45the only difference is this um then you
- 8:49could take
- 8:49this value and multiply it times z
- 8:52uh but uh you could just redo the
- 8:56it would wouldn't take a second to
- 8:58divide that thousand over
- 9:00and just get a new answer .02213
- 9:04meters cubed per kilogram so that is the
- 9:07answer
- 9:08for part b what's the error what's the
- 9:11error well
- 9:12i got .0221
- 9:153 0.02213
- 9:18uh the more accurate was point o
- 9:22[Music]
- 9:26let's see sorry no
- 9:29more accurate was the actual was
- 9:330.021796
- 9:34divided .021796
- 9:38that would give me point zero
- 9:43two let's see what that
- 9:48i probably want some a little bit more
- 9:51accurate
- 9:54uh answer i've rounded it
- 9:57a little bit too much here i think but
- 10:00.02213 minus .02179
- 10:04equals divided by 0.021796
- 10:09and so i've got 0.00162
- 10:18or one point six two
- 10:21percent all right
- 10:28i typed in a number wrong real quick go
- 10:31two two one
- 10:32three .021796
- 10:36divided by .02
- 10:40796 and it's even
- 10:43even lower 0.015
- 10:481.53 all right so the error is
- 10:51more of 1.53
- 10:56so do you see that it is a lot more
- 10:59accurate compared to the 20 percent off
- 11:01that we were just using the ideal gas
- 11:03this one the compressibility factor 0.84
- 11:07allowed us to get closer not quite not
- 11:09exact
- 11:10the best answer was from the property
- 11:12table
- 11:14but this was a good guess
- 11:18pv equals zrt of 0.02213
- 11:22with an error of only about 1.5
- 11:25percent all right
About this transcript
This page contains the full transcript of Thermodynamics - 3-7 Ideal Gas Equation with compressibility factor example 1 by Engineering Deciphered, generated from the public captions YouTube serves with the video. The transcript has 1,382 words across 252 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.