Thermodynamics - 3-7 Ideal Gas Equation with compressibility factor — Transcript
Full transcript
- 0:01Okay, so
- 0:03we can use the ideal gas law, PV = RT,
- 0:06but obviously that's for an ideal gas.
- 0:09Sometimes gases are not ideal and it's
- 0:12under certain pressures and temperatures
- 0:15that they are more or less
- 0:17ideal. And so we want to have a
- 0:20correction factor, all right? That's
- 0:21what this compressibility factor that we
- 0:24can use in our ideal gas equation to
- 0:27correct for
- 0:29the
- 0:30gas not behaving like an ideal gas. So
- 0:32the compressibility factor is a measure
- 0:33of the deviation, right, from an ideal
- 0:36gas behavior.
- 0:37And so now we can use it in our ideal
- 0:41gas law right right in front of the RT.
- 0:43PV = ZRT where Z
- 0:47is the compressibility factor
- 0:52Z factor.
- 0:55It is
- 0:56equal to the actual
- 1:00specific volume over the ideal
- 1:03what the ideal specific volume would be.
- 1:06Z is equal to 1 for an ideal gas.
- 1:10Right?
- 1:11Z is equal 1 for an ideal
- 1:14gas.
- 1:16But Z can be
- 1:19less than one or greater than one.
- 1:21So it's not like it's always less than
- 1:23one. It can be less than one or greater
- 1:25than one.
- 1:26It really just depends. We're going to
- 1:28find Z, the compressibility factor
- 1:31from table A15
- 1:33in appendix one. So let's look
- 1:37at
- 1:38the chart
- 1:40in appendix
- 1:43one. All right, there is no chart in
- 1:46appendix two because this chart is
- 1:47dimensionless. You know, it's not it
- 1:49doesn't matter English units or
- 1:51SI units. It's dimensionless.
- 1:54And and so it is A15
- 1:58in appendix one is it it is the general
- 2:01compressibility
- 2:06chart.
- 2:08All right. So let's look at that.
- 2:11Let's look at our property tables. Let's
- 2:13go to table A15 on
- 2:18uh what page is it on? 26 in mine.
- 2:21Uh
- 2:22right here. I believe it's A15.
- 2:24There's figure A14.
- 2:26Yeah, figure A15.
- 2:28Generalized compressibility chart. Now,
- 2:30you can use this
- 2:32for um
- 2:34any gas. It's not like this is just for
- 2:36water or this is just for refrigerant or
- 2:38this is just for oxygen or air. Uh you
- 2:40can use this for any uh gas.
- 2:44And let's see let's see what it is. All
- 2:45right. So these lines, these red lines
- 2:47show us our compressibility factor.
- 2:50So if we know the reduced pressure
- 2:57and
- 2:58if we know
- 3:01like this line
- 3:03would be a TR line,
- 3:05uh this would be the reduced
- 3:08temperature,
- 3:10then we would read off to the left here
- 3:13our Z, our compressibility factor.
- 3:16Okay. So for example, if we know we'll
- 3:18talk about reduced pressure, but if we
- 3:20know the reduced pressure is 0.7
- 3:22and we know our
- 3:24reduced temperature is 1.15, then I
- 3:26would follow this 1.15 line
- 3:31and I would follow this P
- 3:34R line and right there, right where they
- 3:36intersect,
- 3:38that is going to be
- 3:40the Z, you know, 0.8
- 3:43something, right? Got to look very very
- 3:45closely at it.
- 3:47Okay?
- 3:48So if we know the uh reduced pressure
- 3:51and reduced temperature, then we can get
- 3:53a Z value right here on the Y axis. And
- 3:57we're not going to talk about this
- 3:58reduced volume, but these dotted lines
- 4:01are reduced volumes.
- 4:04Um, we're not going to do that. We're
- 4:06just going to be looking at reduced
- 4:07pressure and reduced temperature. Now,
- 4:08here this
- 4:10top chart
- 4:12is just a really zoomed in chart from
- 4:18zero to one.
- 4:19All right? It's a really zoomed in chart
- 4:20from zero to one.
- 4:22Here
- 4:23this chart goes from Do you see it goes
- 4:25from zero to seven. All right? This
- 4:27chart goes from zero to seven. So that
- 4:28that's the only difference. If it goes
- 4:30from zero to one, we can look at this
- 4:31zoomed in chart right here, but if it if
- 4:34if it's, you know, greater than one, we
- 4:36need to look at this bottom chart right
- 4:37here. Let's go back to our notes.
- 4:41Let's go back to our notes. So let's say
- 4:43for
- 4:44a
- 4:45given PR
- 4:50and a TR
- 4:56you can get a Z value.
- 5:01All right? So for a given reduced
- 5:04pressure on the x-axis
- 5:07and a given
- 5:08uh
- 5:09TR, the solid
- 5:12Uh, that's the solid green lines or
- 5:13those red lines?
- 5:15Solid
- 5:17red lines and it might be green lines.
- 5:20Uh, then you can get a Z value from the
- 5:23Y
- 5:24axis. All right? You can get a Z value
- 5:26from the Y axis. In general, if you if
- 5:28you have two out of three out of these
- 5:30three, you can get the third one. But
- 5:31what we're going to be doing is if we
- 5:33know the reduced pressure and reduced
- 5:34temperature, then we can get a Z value
- 5:36we can plug into our chart. So what is
- 5:39PR and TR? It is reduced pressure and
- 5:43reduced temperature. It's a comparison
- 5:45of the pressure to its critical point
- 5:48pressure.
- 5:50All right? So it is the, you know,
- 5:52actual pressure that you've got
- 5:56divided by the critical
- 6:00point
- 6:01pressure.
- 6:03All right?
- 6:04The reduced temperature is the
- 6:07critical
- 6:09point
- 6:11temperature
- 6:13and you can get this
- 6:16from
- 6:17table
- 6:21A 1. You can get this critical point
- 6:25from table A 1.
- 6:30So air has a critical pressure and a
- 6:34critical temperature, critical point
- 6:36pressure, critical point temperature.
- 6:38Um
- 6:39you know oxygen
- 6:41water, refrigerant, everything has a
- 6:43critical point temperature and pressure.
- 6:44Let's look at table A 1.
- 6:49See if we can find it.
- 6:53Here here we go. Here are its critical
- 6:55point properties, critical point
- 6:58properties.
- 7:00Um and so uh the closer it is to the
- 7:03critical point the more that then it's
- 7:06the reduced pressure is going to be one,
- 7:08the reduced temperature is going to be
- 7:09one. If we look back at this
- 7:12um
- 7:14chart
- 7:17Did I pass it?
- 7:19No, table A 15.
- 7:23Uh the closer these are to ones then our
- 7:27Z value is you know 0.2
- 7:312 0.2 you know a very very low Z value
- 7:36which means it's farthest away from
- 7:38ideal. All right. That critical point is
- 7:41just is a weird point we won't get into
- 7:43but it's it's where uh of gas and
- 7:46liquids
- 7:48are there's no real phase change between
- 7:50gas and liquids. It gets all fuzzy um at
- 7:53that pressure and that temperature. They
- 7:55can exist in in the same at the same
- 7:58point in time.
- 7:59Um all right. So
- 8:02if you know the actual pressure
- 8:05and you know the actual temperature then
- 8:07divide them by their critical values,
- 8:10and then you've got your reduced
- 8:12pressure and your reduced temperature.
- 8:15Okay?
- 8:16Uh if you look at table A15
- 8:23if you look at table A15
- 8:26uh and you notice a few things, Z is
- 8:28equal to one would be an ideal gas.
- 8:34And that Z was on the left hand, the the
- 8:36y axis. Um we could look at this
- 8:40at very low
- 8:44and very high
- 8:47reduced
- 8:50pressures.
- 8:51At very low and very high reduced
- 8:53pressures,
- 8:57it behaves like an ideal gas.
- 9:03So if the reduced pressure is
- 9:06you know, if the actual pressure is
- 9:08higher than the critical point pressure
- 9:09or the actual pressure is lower than the
- 9:11critical point pressure, and the more
- 9:13higher and lower it is, then it behaves
- 9:15more like an ideal gas. So let's look at
- 9:16pressures.
- 9:18Let's look at pressures.
- 9:20If pressure is really low, then we're up
- 9:22here, you know, closer. If pressures are
- 9:25really high, then we're up here, you
- 9:28know, closer, you know, we're above and
- 9:30below one.
- 9:32Whereas if we are
- 9:35in here, then some of these values may
- 9:37could could be pretty low. So if we look
- 9:39at the pressures right there.
- 9:41What about the temperatures? Let's look
- 9:42at these T values.
- 9:48Here is TR of
- 9:51one.
- 9:53But if it's 1.1, if it's 1.3, if it's
- 9:561.5, if it's two, you know, those get um
- 10:01better and better, closer and closer to
- 10:04uh one, right? Uh how about these right
- 10:07here?
- 10:08Um
- 10:10if we look at these
- 10:12T values.
- 10:17Here's T is equal to 1, here's 0.95. So
- 10:21the higher the T value, it behaves more
- 10:25and more like an ideal gas. Let's go
- 10:27back to our notes.
- 10:31At higher temperatures
- 10:36and also higher reduced temperatures,
- 10:39like maybe a TR greater than 2,
- 10:44then our Z if our Z value is only 0.9
- 10:46point 95 0.97
- 10:50then it's behaving more and more like an
- 10:52ideal gas. Behaves like
- 10:55an ideal
- 10:58gas.
- 11:00But nearest the critical point
- 11:07when PR is 1, TR is 1,
- 11:11it is most
- 11:13unlike
- 11:16ideal gas. Most unlike ideal gas. All
- 11:19right. So but do you see what we're
- 11:21we're doing? We're going to take the
- 11:22actual pressure and divide it by the
- 11:24critical pressure from table A1. We're
- 11:26going to take the actual temperature
- 11:27divided by the critical temperature.
- 11:29These are absolute temperatures.
- 11:33You will get different answers. Even
- 11:35though it looks kind of unitless, you
- 11:37would think that degrees C over degrees
- 11:38C would be the same as K over K. No,
- 11:42because they're off by you know 273.
- 11:45These have to be absolute temperatures
- 11:47right here.
- 11:50Also we're going to take the temperature
- 11:51divided by the critical point
- 11:53temperature from table A1. Then we're
- 11:55going to take those two values. We're
- 11:57going to go to the table A15 and we're
- 12:00going to read off a Z.
- 12:02And then we're going to use PV equals
- 12:04ZRT. All right? And this method will
- 12:07give us a better answer than just PV
- 12:10equals RT.
- 12:12Right? Now it's it's a lot more work.
- 12:14We can kind of determine whether it's
- 12:16worth it.
- 12:17Um and especially if if it's at very
- 12:20high temperatures, maybe it's not worth
- 12:22it. If it's if it's away from the
- 12:24critical point, maybe it's not worth it.
- 12:26But if we give it will give us a better
- 12:28um answer
- 12:30for what we're solving for. If we're
- 12:32solving for, you know,
- 12:35V, if we're solving for uh specific
- 12:37volume or something like that. All
- 12:39right?
- 12:40So let's practice.
About this transcript
This page contains the full transcript of Thermodynamics - 3-7 Ideal Gas Equation with compressibility factor by Engineering Deciphered, generated from the public captions YouTube serves with the video. The transcript has 1,644 words across 301 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.