Plastic In. Metal Out. | Electroplating 3D Printed Parts for Metal Performance (Part 1) — Transcript
Full transcript
- 0:00This may look like an ordinary metal
- 0:02housing that was CNC machined, but what
- 0:05if I told you that the manufacturing
- 0:07process used to make this is the same as
- 0:11what was used to make this? And if
- 0:14that's not surprising enough, what if I
- 0:17also told you that both of these started
- 0:19out as 3D printed plastic parts?
- 0:23This conversion from plastic to metal is
- 0:26possible with electroplating. And in
- 0:29today's webinar, we'll expose you to one
- 0:31of the most powerful post-processing
- 0:34techniques available for your 3D prints.
- 0:41Electroplating is the process of using
- 0:43electricity and an electrolyte solution
- 0:46to transfer positive metal ions from one
- 0:49metal electrode like copper to another
- 0:52electrode, resulting in a thin metal
- 0:55coating. Traditionally, this other
- 0:58electrode is also made of metal because
- 1:01it's naturally conductive, but it
- 1:03doesn't have to be. Non-conductive
- 1:06substrates like plastic, can also be
- 1:09plated once an ultra thin conductive
- 1:12layer is applied. And plastic,
- 1:15particularly 3D printed plastic, is
- 1:18where you often see the most profound
- 1:20benefits of electroplating. When 3D
- 1:23printed plastic parts are electroplated,
- 1:26it creates a composite where the whole
- 1:28is truly greater than the sum of its
- 1:30parts. Thanks to the metal coating, the
- 1:33parts can be stiffer and more rigid,
- 1:37thermally and electrically conductive.
- 1:41They have improved aesthetics,
- 1:44and are vastly more resistant to harsh
- 1:47environments, to chemicals, and UV
- 1:51light. And the benefits don't stop there
- 1:53because with 3D printing, you have a
- 1:56lightweight plastic core and the ability
- 1:58to produce geometries impossible to
- 2:01manufacture traditionally.
- 2:03Lastly, thanks to the lowcost nature of
- 2:053D printing, using electroplating to
- 2:08achieve metal properties is often
- 2:10cheaper than casting or machining.
- 2:13It's easy to see how electroplating 3D
- 2:15printed parts can unlock applications
- 2:18into a wide variety of industries.
- 2:21To demonstrate this, we 3D printed nine
- 2:24different parts representing automotive,
- 2:27consumer products, maritime,
- 2:30entertainment, architecture, and
- 2:32electronics in addition to parts that
- 2:36illustrate electroplating's various
- 2:38superpowers.
- 2:40The decision to print these parts in
- 2:41gray V5, rigid 10K, and nylon 12 on our
- 2:45Formlabs printers, as well as
- 2:47understanding the different plating
- 2:49options available and the clearances
- 2:52that are needed to account for the
- 2:53different plating thicknesses could only
- 2:56happen thanks to the expert guidance at
- 2:58Repl. Having electroplated 3D printed
- 3:02parts for customers in nearly every
- 3:04industry for over 25 years, they have
- 3:06easily earned the title of masters of
- 3:09their craft. I met with Repl's president
- 3:12and founder, Dr. Sha Weiss, and
- 3:15extracted some important excerpts from
- 3:17our conversation.
- 3:19>> I'm Sean Weise. I'm the president of
- 3:20Replform. The company's been established
- 3:22for 26 years. I've been electroplating
- 3:26on additive manufactured parts since the
- 3:29mid mid to early 90s. [snorts] So more
- 3:32than 30 years. When I started out, I was
- 3:35making electroforms that were a tenth of
- 3:37an inch thick. So not really bending
- 3:39metal, but creating shapes um that way
- 3:42off of SLA patterns. Now most of the
- 3:44coating that we do is anywhere between
- 3:4620,000 and 6,000 of an inch. So we work
- 3:50at much much thinner layers. Plus the
- 3:52the parts that people print are
- 3:54generally, you know, an eighth of an
- 3:55inch or less for wall thickness. Not
- 3:57always the case, but um we can reinforce
- 4:00those parts with the plating because the
- 4:01plating is about 20 times stronger than
- 4:04the plastic resins and about 50 times
- 4:06stiffer. So, we change the mechanical
- 4:08properties substantially.
- 4:10I wanted to briefly interrupt here
- 4:12because Shawn shared a video outlining
- 4:15Repl's electroplating process. It's very
- 4:18insightful. So, by playing it now, it'll
- 4:21help make the rest of the conversation
- 4:23make a bit more sense. Let's check it
- 4:25out.
- 4:25>> After printing, the parts are removed
- 4:27from the platform and rinsed twice in
- 4:29IPA baths with a final spray rinse with
- 4:32clean IPA. The parts are then cured
- 4:35thoroughly and light cured to ensure
- 4:38there is no residual unccured resin,
- 4:40which will interfere with the
- 4:42metalization step.
- 4:44The lightweight parts with a high
- 4:46surface area
- 4:48use a loose hold on a rack so that parts
- 4:50can move while plating. After racking,
- 4:53the parts will be sprayed with a fine
- 4:54abrasive to provide a good edge for the
- 4:56conductive layer to adhere to. The
- 4:58metallization line is four process baths
- 5:01with each one followed by a rinse and
- 5:04deionized water. It starts with a soap
- 5:06solution to remove any residual soils
- 5:09from the earlier steps.
- 5:17The second bath is a mixed activator
- 5:19catalyst system that makes the surface
- 5:21of the part susceptible to autocatalytic
- 5:23nickel deposition.
- 5:31The third bath is an accelerator that
- 5:33complexes out the activator portion of
- 5:35the previous bath, making the final step
- 5:38in the process proceed more quickly.
- 5:47The final bath which is dark blue is the
- 5:49autocatalytic nickel deposition where 1
- 5:52microns of nickel phosphorus conductive
- 5:54layer is applied. The time to one rack
- 5:56through the four process and rinse tanks
- 5:59in this line is about 40 minutes.
- 6:06After a final rinse in DI water, the
- 6:08parts are dried and tested for
- 6:09electrical continuity to the rack. We do
- 6:12a 100% inspection for conductivity to
- 6:15ensure complete autocatalytic nickel
- 6:17coverage on the parts prior to
- 6:19electroplating.
- 6:20The first electroplating step is almost
- 6:23always a copper layer. The copper baths
- 6:25deposit at a rate of six or 12 microns
- 6:28per hour depending upon the type of
- 6:30copper we apply. The lattice cubes
- 6:32typically get 50 microns of copper. So
- 6:35run so they run a little over eight
- 6:36hours in this tank.
- 6:39The copper lattice cubes are removed
- 6:41from the acid copper tank at the
- 6:42prescribed time and rinsed.
- 6:51They are then placed in a nickel
- 6:52sulfamate tank with power connected.
- 6:56We apply a nickel layer on the lattice
- 6:59cubes which is 125 microns thick. It
- 7:02begins with a deposit from a ductal
- 7:03nickel bath followed by a layer of hard
- 7:05nickel. Deposition rate is six microns
- 7:08per hour.
- 7:14The rack coming out of the hard nickel
- 7:15band tank is rinsed thoroughly as this
- 7:18is the last step in the plating process.
- 7:23The lattice cubes are unrackcked after
- 7:25plating. Parts are weighed to confirm
- 7:28the average metal thickness prior to
- 7:29plating. The parts weigh about six grams
- 7:33and 175 microns of copper and nickel
- 7:35plating should increase their weight by
- 7:3725 or so grams, bringing the total
- 7:39weight of the parts to above 30 g. With
- 7:43that, they are strong enough so that
- 7:45[clears throat] people can stand on them
- 7:46without fear of breaking.
- 7:53The pretty materials that I was kind of
- 7:54looking at primarily is SLA. So, I'm
- 7:58looking at general purpose resins. Gravy
- 8:005 is what we have quite a lot of on hand
- 8:02just through our form four printer. And
- 8:05we also have some rigid 10K.
- 8:07>> The the plating on it works pretty well.
- 8:09And it seems that most of the business
- 8:11we're getting in the 10K is um mold
- 8:13inserts and things like that to make
- 8:14them last a little bit longer.
- 8:17>> Oh, wow. Okay. Very interesting. Yeah,
- 8:19we uh we recently had some experience
- 8:20with Rigid 10K mold inserts. We had not
- 8:23considered plating them though. But what
- 8:24happens is it can very easily get too
- 8:26hot. And if it gets too hot, then the
- 8:29resin, the injection molded resin can
- 8:31stick to the Rigid 10K and start picking
- 8:34out surface detail. The plating helps
- 8:36spread the heat a little bit. Doesn't
- 8:38reinforce it that well because there's
- 8:40the plating is usually only about 4,000
- 8:43thick and the parts are half an inch to
- 8:45an inch thick. But the detail areas will
- 8:48hold up better if the plating's on it.
- 8:50Our customers tell us that three to five
- 8:52times more parts can be made on the
- 8:54tools after they're plated.
- 8:56>> Oh wow. So the other material that I was
- 8:58thinking we have a fuse in our Dallas
- 9:00location. So maybe uh we could print Oh,
- 9:03we just run nylon 12 on that on that
- 9:05printer.
- 9:06>> And that's fine. We we run a lot of
- 9:07PA12. Um I would say the bulk of the
- 9:10stuff we see these days is MJF from the
- 9:12HP machines and it works pretty well.
- 9:15We've got a lot of data on reinforcing
- 9:17PA12 that's made by the MJF method and I
- 9:20know the form lab's properties of the
- 9:22printed parts are very very similar. Um
- 9:25they tend to be fairly dense. We will
- 9:26look at densities of printed parts
- 9:27really carefully when we're dealing with
- 9:29centered parts because if a part is
- 9:32nearly fully dense, like between 95 and
- 9:3698% dense, it's probably going to run
- 9:38just fine. If it's under 90% dense,
- 9:41we're probably going to have a lot of
- 9:42standing issues and problems with it.
- 9:43It's a very simple screening technique
- 9:45that you can do with a balance in about
- 9:4730 seconds. And the other thing too is
- 9:49with the SLS, the gray [clears throat]
- 9:51material works a lot better than the
- 9:53white material. So the white material
- 9:55doesn't give you as high a density as a
- 9:57gray material, which is kind of to be
- 9:59expected because it just absorbs more
- 10:01laser energy.
- 10:03>> Is there any issues with uh because I
- 10:05know Formlapse puts like carbon black to
- 10:07I guess add that coloration. Does that
- 10:10cause any issues with the plating
- 10:11process? Um, we don't really seem to
- 10:13There are a lot of people that send us
- 10:14parts that are dyed, whether it's carbon
- 10:16black or something else. It's It's not a
- 10:18problem. It all just coats. And the fact
- 10:21that there's like chopped carbon fiber
- 10:22in that material. That was another thing
- 10:24I was wondering if that because I just
- 10:26know of carbon's conductivity. I didn't
- 10:28know if that threw off anything in the
- 10:30plating process.
- 10:31>> It needed to be conductive to get it to
- 10:33plate. Although it's not good enough to
- 10:34plate without a conductive layer
- 10:36applied, but no, it doesn't interfere
- 10:37with anything at all.
- 10:39We have worked with the onyx materials
- 10:42that the Mark Forge plates. The Mark
- 10:44Forge actually plates a tighter part
- 10:47than and particularly with the Onyx than
- 10:49you get from most FDM printers. So, we
- 10:52actually don't do too badly when
- 10:55somebody sends us an FDM print made with
- 10:58Onyx that's been vapor smooth. It often
- 11:00does well enough by itself that we don't
- 11:02need to go through a sealing process
- 11:04because the vapor smoothing process
- 11:06seals it because it's a tighter
- 11:08structure than you normally get out of
- 11:09an FDM printer. Most other FDM prints,
- 11:13we really need to use a resin seal
- 11:15because they have much coarser pores
- 11:16that come to the surface in odd places.
- 11:19The Mark Forge prints, you know, you
- 11:21tend to have more of a of a racetrack
- 11:23type of reinforcement if you're doing
- 11:25the continuous fibers. the
- 11:28electroplating puts a lot of fibers
- 11:30right at the surface and so it basically
- 11:33brings back the bending properties so
- 11:36that they're at least as good as the as
- 11:38the tensil properties. So it's a it's a
- 11:40really nice complement to the uh to what
- 11:42you can do with the uh the fibers and to
- 11:44make a high tensil strength part.
- 11:47>> You wouldn't have to do any
- 11:48post-processing steps prior to plating
- 11:51uh like where you have to seal the
- 11:52surface or anything. Uh assuming
- 11:55>> it it does need to be made well. It does
- 11:57does need to be cleaned well because if
- 11:59the surfaces have a lot of powder on
- 12:01them, they're not going to metalize
- 12:02well. But that shouldn't be that
- 12:04difficult.
- 12:05>> When it comes to plating a chain mail
- 12:07like that, you have to hold it really
- 12:09loosely.
- 12:11>> And the copper is much more likely to in
- 12:15essence grow together and bond. Okay?
- 12:18>> So you you literally have to break it up
- 12:20periodically while it's plating. And
- 12:23then you go into the nickel tank and you
- 12:26still worry about that, but you can go
- 12:28about four times as long. It normally
- 12:31does not. If you can get it through the
- 12:32copper tank without sticking to itself,
- 12:34you'll get it through the nickel tank
- 12:35without too much difficulty.
- 12:37What really matters is the quality of
- 12:40the print and how well it's finished.
- 12:43So, if you want something that's
- 12:44polished, you're going to have to make a
- 12:46part that is probably printed at a
- 12:49maximum of 50 micron build layer
- 12:51thicknesses. You're going to have to
- 12:52sand it and get rid of all the layer
- 12:54lines and make certain the top layers
- 12:56are very smooth. And then we usually
- 12:59plate at least 100 microns to 150
- 13:02microns of copper. And our we have a
- 13:04bath that actually levels out the
- 13:06surface a little bit um to get a bright
- 13:08copper layer. And then the nickel layer
- 13:09is only for finish work about 25
- 13:12microns. So in other words, you're doing
- 13:14most of the work is being done in the
- 13:16copper tanks and there may still be a
- 13:18little bit of work afterwards.
- 13:20>> Understood. And so it sounds to me like
- 13:22any kind of defects or or or surface
- 13:24imperfections in the printed part is
- 13:26really going to be like amplified or
- 13:28it's really going to show through uh
- 13:30after. Okay. In fact, one of one of the
- 13:33difficulties we have, a lot of people
- 13:34like to spray parts with um bead
- 13:36blasting and it makes the surface dull
- 13:38and you don't see any of the flaws. As
- 13:41soon as you put particularly a bright
- 13:44layer of plating on, every single one of
- 13:46those flaws that was hidden comes come
- 13:48basically becomes really prominent
- 13:50because you go from a low contrast
- 13:52surface to a very high contrast surface
- 13:54when you play parts.
- 13:56>> So, I saw you had some bronze patina
- 13:58coating.
- 13:59>> Yeah. which is really just copper with a
- 14:01a bronze patina finish. So, it's it's
- 14:03relatively easy to do. We would give you
- 14:05probably a semi- bright copper layer and
- 14:07then um the bronze patina gets applied
- 14:10and usually gets might get highlighted
- 14:12with steel wool or something like that.
- 14:15>> Can you uh enlighten me a little bit on
- 14:17what the like patina application process
- 14:19looks like?
- 14:20>> For cold patas, which is what we have to
- 14:24work with when we're dealing with plated
- 14:25plastic parts, we use a gel that we
- 14:27wipe. We basically spread over the
- 14:29surface, but you can also buy the patina
- 14:31in a like you can have it in a liquid
- 14:34container and you literally dip the part
- 14:36in in the patina for a certain period of
- 14:38time and you hold it in there and you
- 14:42take it out and you you dry it off.
- 14:45Sometimes you have problems where you
- 14:46might get a little bit of skip and you
- 14:47have to go back and redo it, but um and
- 14:50then you would highlight it. There's
- 14:52probably maybe a little bit of pre-work
- 14:53that needs to be done. It's really not
- 14:55that hard to apply a patina. There may
- 14:57be a little bit of prep work up front to
- 14:59basically make it just a little bit
- 15:01rougher than we normally get out of the
- 15:02tank, but that shouldn't be that hard to
- 15:04do.
- 15:06That little cube, it will hold 1,800 lb
- 15:09in the orientation you show.
- 15:12>> And if you turn the tube sideways, it'll
- 15:14hold 800 lb.
- 15:15>> So,
- 15:16>> oh my gosh,
- 15:17>> it's and and that's about 10 times more
- 15:19than it would hold if you didn't plate
- 15:21it. It's c that kind of lattice where
- 15:24you have a very high surface to volume
- 15:26ratio and a very high volume fraction of
- 15:28metal and we can get into that later.
- 15:30You get some really big time
- 15:33strengthening. You know, we don't do a
- 15:35lot of lattice parts and we actually
- 15:36wish we did a lot more because we're
- 15:38printing and plating. It is probably
- 15:40easier than conventional parts. So, we
- 15:43really like them, but we're trying to
- 15:45get more people to try more latisy type
- 15:48of things. And um we're slowly get
- 15:50they're slowly coming around. We've done
- 15:52work with a topology optimized
- 15:55threepoint bend sample and
- 15:57[clears throat] we literally designed it
- 15:58so it had the same tensil strength. The
- 16:01material had the same tensil strength as
- 16:02DMLS aluminum.
- 16:04>> Oh wow.
- 16:04>> And then and then when we broke a plated
- 16:08part this a very high metal volume
- 16:11fraction or the content was around I'd
- 16:13say 35% or so. It had it was actually
- 16:17twice as strong as the DMLS aluminum
- 16:18piece. And the reason for that was all
- 16:21the reinforcement is out on the surface.
- 16:24Whereas the DMLS aluminum piece, even
- 16:26though it has the same tensil strength,
- 16:28the reinforcement is uniform across the
- 16:31you know the it's a uniform tensil
- 16:33strength. So the I think the DMLS
- 16:34aluminum would has a tensil strength of
- 16:3750,000 PSI, but in bending you've got
- 16:39surface loads and the surface
- 16:41reinforcing layer is about 150,000 PSI.
- 16:44So, you actually get a better result
- 16:46with a plated plastic part.
- 16:48>> The the core of that plastic part that
- 16:50was plated, was it was it an SLA part?
- 16:53>> SLA clear resin standard stuff. Nothing
- 16:56special.
- 16:57>> Oh my gosh. So, not even like like a
- 16:59Ridge 10K or anything, just like your
- 17:01general purpose. That's
- 17:02>> what's funny is when you do when you
- 17:04have low volume fractions of metal on a
- 17:06part like you might with a housing
- 17:08that's got um let's say 1 millimeter
- 17:10walls and and maybe 75 microns of
- 17:13plating on it. The stiff materials
- 17:15really really do a lot better. When you
- 17:18get to 25 30% volume metal that stiff
- 17:23material doesn't help you very much
- 17:25anymore. the the metal is dominating and
- 17:27because a stiff material tends to
- 17:29fracture very easily and the tougher
- 17:32materials have a lot better elongation,
- 17:35they actually do a little bit better.
- 17:36And we've got data on that that we got
- 17:38with Form Labs that shows exactly that.
- 17:41If you have a high metal volume
- 17:42fraction, the coating has better strain
- 17:45capability than what's underneath it. So
- 17:48the rigid 10K breaks at the low volume
- 17:51fractions, they're working together.
- 17:53You'll often heard hear me talk about
- 17:55metal volume fractions because that's
- 17:57really how you need to be thinking about
- 17:59things and that's the the volume of
- 18:02metal versus the volume of plastic in
- 18:04the cross-section that's tested. That's
- 18:06how you predict what the parts are going
- 18:07to be.
- 18:08>> Yeah, that goes back to that rule of
- 18:10mixtures that you guys
- 18:11>> Yes, it does. It's exactly it.
- 18:13>> Okay. What are some of the applications
- 18:16where like abrasion resistance would
- 18:18would really be uh would really apply?
- 18:20Where the abrasion resistance matters is
- 18:23often when we are are dealing with parts
- 18:25that you know one thing slides against
- 18:27another or there may be abrasive
- 18:29particles coming through a tube or a
- 18:31pipe or something of that nature. And
- 18:33the way to get abrasion resistance is
- 18:36nearly all the work we do for
- 18:37strengthening uses electrolytic nickel
- 18:39because electrolytic nickel has good
- 18:42strength and good elongation. If you're
- 18:45after abrasion resistance, you need to
- 18:47use electroly nickel, which [snorts] is
- 18:49a nickel phosphorus material. And that
- 18:52material is twice as hard as
- 18:55electrolytic nickel. And it doesn't tend
- 18:59to gall the way nickel can when you have
- 19:02nickel sliding against itself because
- 19:04it's a harder surface. But you don't get
- 19:06much reinforcement from that electroly
- 19:08nickel. So, if you're making an abrasion
- 19:10resistant coating that needs to be and
- 19:12and you need a part that's also strong,
- 19:15what you do is you use you start with a
- 19:16regular copper layer as as your base
- 19:18layer, then you use the amount of
- 19:21electrolytic nickel you need to get the
- 19:23strength out of it and then you might
- 19:25put a top coat of maybe 25 microns of
- 19:28electrolytes nickel to give you the bra
- 19:29the abrasion resistance you're looking
- 19:31for. It's just a question of sequencing
- 19:33and putting that top layer on. And you
- 19:35probably need to be a little bit careful
- 19:36about sizes and the resins because when
- 19:40you're the electroly nickel is applied
- 19:42at 90° C whereas all the electrolytic
- 19:45work is done at under 45° C. And so it's
- 19:49you can probably get away with almost
- 19:51anything with electro blading. You're a
- 19:53little bit more limited when you get to
- 19:54the electrolyt materials particularly as
- 19:56you get larger parts.
- 19:58>> Okay, understood. Yeah. So it sounds
- 20:00like the uh you need like a higher
- 20:02performance resin if anything that can
- 20:04that can handle those temperatures.
- 20:06>> Well, you also want a low CTE resin and
- 20:09so that's actually one of the places
- 20:10where using a um a rigid 10K has real
- 20:14advantages since we don't run our
- 20:17electroly nickel that often and and we
- 20:19don't run large baths of electroly
- 20:21nickel. We tend to have to make it up
- 20:22and throw it out. So it does add cost.
- 20:24But if we had baths that we ran
- 20:26routinely, then the electrolist nickel
- 20:28wouldn't cost that much more to get that
- 20:30layer applied. How does a plated plastic
- 20:33do versus a printed copper piece? And in
- 20:37order to get good conductivity through a
- 20:38piece of copper, you really want to have
- 20:41all copper from one side to the other.
- 20:43[snorts] I would bet on the bottom of
- 20:45that plate there, it is um a solid
- 20:48copper piece. Then you have those other
- 20:50pieces rising up off of it. Well, if we
- 20:52had a plastic plate, we're pling over
- 20:54it. We now have an insulating layer. So,
- 20:57we would probably want that plate
- 20:59perforated. We'd probably want to run
- 21:01samples through it, but we're only going
- 21:02to get the conductivity that you'd get
- 21:03from the copper layer, which might only
- 21:06be, let's say, 150 micron thick, 6,000
- 21:08of an inch thick, and it's not going to
- 21:10probably work as well as as a solid
- 21:12copper piece.
- 21:14>> Logical conductivity is literally
- 21:16>> 20 magnitudes higher than it than the
- 21:18plastic is. But the thermal conductivity
- 21:22is three orders of magnitude higher. So
- 21:24it's you know you're it's going to help
- 21:27but you really need a high metal volume
- 21:29fraction to do a lot. But you all but
- 21:32remember because there's plastic there's
- 21:35going to be a path dependency that you
- 21:36we have to be very careful careful of
- 21:38and conscious of in the way the heat
- 21:40sink is designed.
- 21:43electroplating. Does it have the
- 21:45capacity to take a 3D printed part that
- 21:48is uh for the most part not food safe
- 21:51and to some degree not necessarily
- 21:53biocompatible? Is it capable of of
- 21:55achieving that level of uh of like
- 21:58certification and safety?
- 22:00>> Well, I know that there's electroplating
- 22:02of nickel that's used for food safe
- 22:05applications. I know that that occurs.
- 22:07It's mostly people plating on metals.
- 22:09[snorts] any specific reason why the
- 22:12core of the part be metal versus plastic
- 22:14for food?
- 22:15>> Probably the the number one thing is the
- 22:18bond to metal of of electroplated
- 22:21coating to metal is much much stronger
- 22:23than the bond of electroplated metal to
- 22:25plastic. Plastic just doesn't have the
- 22:27tensil strength even if you've got a
- 22:29decent bond. So the chances of something
- 22:31breaking or you could, you know, get
- 22:33delamination and get a blister and then
- 22:35that could lead to other problems. So it
- 22:37it probably has more to do with is the
- 22:41coating but what's the likelihood of the
- 22:42coating coming off the part and leading
- 22:45a to a contamination problem in the
- 22:47food. And that's really what what I
- 22:49think the issue is going to be. It is
- 22:51not going to be safe for uh somebody
- 22:53making a an implant or something like
- 22:56that. I think there's like a literally a
- 22:58handful of metals maybe um six to 10
- 23:01that you can use for implants and things
- 23:03like that. Chrome is one of them.
- 23:06stainless steel, which does contain some
- 23:08nickel, um, but but only certain alloys.
- 23:10Titanium,
- 23:12you know, you're really limited in what
- 23:13you can implant people with. There's
- 23:15about a third of the population has a
- 23:18has sensitivity to nickel and so it's
- 23:21it's not the sort of thing you can ever
- 23:23think about implanting at all. I mean,
- 23:25you can make prototypes and people can
- 23:27test out those prototypes, but they're
- 23:29not going to be an implantable item. I I
- 23:32saw that one of the coding options that
- 23:34you have was EMI like EMI shielding. I I
- 23:37would take it as
- 23:39>> that's a big part of our business. Okay.
- 23:41And normally it's not just copper. It's
- 23:43usually mostly copper with a little bit
- 23:45of nickel applied over it.
- 23:46>> Copper will oxidize over time. So a
- 23:49little layer of nickel prevents that.
- 23:50You know, you've got a box there that's
- 23:52got 3mm walls. And you can take that
- 23:55same box and make it 1 mm walls and now
- 23:59put a mill of copper which is what you
- 24:01need for your EMI shielding and then 2
- 24:03mls of nickel which you would need for
- 24:05strengthening. And now you might
- 24:07actually end up with a lighter box and
- 24:09that's um a lot more resilient. We do a
- 24:12lot of work with aerospace companies and
- 24:14it's rare to see an EMI shielding box on
- 24:18an aircraft that's going to fly,
- 24:20[snorts] you know, mostly drones and
- 24:22things like that. They're almost all one
- 24:23millimeter wall thickness parts and
- 24:26using at least equal parts of copper and
- 24:29nickel and sometimes twice as much
- 24:30nickel as copper.
- 24:32>> Oh wow. And and again this is for the
- 24:34shielding of any kind of interference.
- 24:36That's
- 24:36>> it's shielding but it's also
- 24:38strengthening of the part. So it's a
- 24:40it's a multifunctional coating which is
- 24:42not that hard to do when you're just
- 24:44going bath to bath.
- 24:46>> Are you seeing use cases for this stuff
- 24:48like on aircraft or is it primarily
- 24:51drones?
- 24:52from our understanding is most of these
- 24:54are for UAVs. And in all honesty, the
- 24:57UAV is a much better place to be these
- 25:00days than aircraft because we're
- 25:01spending a lot more money on drones than
- 25:04we're spending on aircraft. And the
- 25:05barriers to getting onto that aircraft
- 25:07are a lot smaller.
- 25:09>> I guess the FAA probably has a lot fewer
- 25:12restrictions on on what can go on a
- 25:14drone than what can go in an aircraft.
- 25:17anything with people in it, you've got
- 25:19to be really, really careful and you're
- 25:20going to go through all kinds of
- 25:22certifications.
- 25:24>> You're making a drone or particularly
- 25:25even a one-way piece,
- 25:27>> you know, you've got latitude that you
- 25:29just don't have. And that's why saying
- 25:31the barriers are lower to getting in and
- 25:34the applications are numerous
- 25:36>> and the [clears throat] size of the
- 25:37parts is compatible with what you can
- 25:39print.
- 25:40So the the box on the right, you know,
- 25:44down here,
- 25:45>> that's a plated electrical box with one
- 25:47mil of copper, two mills of nickel, and
- 25:49then that's the unplated box on that's
- 25:51white behind it. And that's all made
- 25:53from rigid 4K.
- 25:56>> Okay. Terrific.
- 25:57>> And the rigid 4K one broke, but the ri
- 25:59but the plated one's doing just fine,
- 26:02>> I bet.
- 26:04Very nice.
- 26:06Sometimes it's relatively easy to take
- 26:08an antenna as it's designed. Other times
- 26:11people want to make a resident cavity
- 26:13where you basically have a closed box
- 26:15with a few openings in it here and
- 26:18there. In many cases, those are
- 26:20impossible to plate. And one of the
- 26:23things that we've had the opportunity to
- 26:25work with people who are very good
- 26:26antenna designers, they know how the way
- 26:30the antenna works. They know where you
- 26:32need material and when you don't need
- 26:33material. And then they take that
- 26:35antenna and they turn it into Swiss
- 26:39cheese in a way that it still functions
- 26:41properly as an antenna, but now it's
- 26:43really easy to plate. So, um, it's that
- 26:46kind of level of interaction between how
- 26:50the part really functions and what you
- 26:52can electroplate. In other words, when I
- 26:55talk to people about lattice structures
- 26:56or perforated structures, the probably
- 26:59the the the strangest thing that they'll
- 27:01hear from me is it's easier to plate a
- 27:04lattice structure than it is to plate a
- 27:05solid structure. With solid structures,
- 27:08you know, the wall thickness may be too
- 27:10thick. We may have to use supplemental
- 27:11anode. When you when you make a lattice,
- 27:14all of a sudden, all those problems go
- 27:16away.
- 27:17But uh like selectively masking areas is
- 27:20that's what what kind of goes in with
- 27:22that if it's even possible.
- 27:24>> What I'm going to say about selective
- 27:26work is what we do is we literally just
- 27:30tape off areas that need to be masked.
- 27:33[snorts]
- 27:33>> Okay.
- 27:34>> But on the other hand, if you can figure
- 27:36out how to do the masking
- 27:39or the selectivity
- 27:41in the printing process
- 27:44>> Mhm. that would make this really
- 27:46efficient and easy. Let's say you want
- 27:48an area that where you're going to be
- 27:50selectively, you know, having some
- 27:52circuits or something like that on it.
- 27:54Well, maybe all the circuits are
- 27:55recessed and then all the areas that are
- 27:57not to be plated will be raised. Then we
- 28:00could basically metalize everything with
- 28:02conductive layer. Don't plate it yet.
- 28:04And then remove all the height all the
- 28:07conductive layer off of the high spots.
- 28:09Then electroplating electroplate that
- 28:12and we have circuits. I think the key to
- 28:15making that selectivity work is do the
- 28:19selectivity in the printer because the
- 28:20printer is much more accurate than what
- 28:22people can do by hand. Uh
- 28:24>> best to send us files to to evaluate and
- 28:27we can give you a quote based upon files
- 28:30>> and would you prefer like step files or
- 28:32or something even
- 28:34>> STL files are preferred but we can we
- 28:36can we can deal with steps too if that's
- 28:38all you have. We do a lot of parts that
- 28:41have to fit together and a lot of times
- 28:44people will design the parts you know
- 28:46just to be printed and that's you know
- 28:48the end of it. When we start adding
- 28:51layers to it we're going to create
- 28:52interferences
- 28:54but with STL files or with step files
- 28:57it's very easy to offset surfaces
- 28:59inwards to make room for the coating.
- 29:01And we believe very very strongly that
- 29:04the process starts before you even print
- 29:07the part because you need to understand
- 29:09how much material you need for the job
- 29:11you're doing and then you have to modify
- 29:14the file before you print it. That's
- 29:17really essential to make this work well.
- 29:20I know uh you've talked about like screw
- 29:22threading before that one is a a
- 29:25>> for for small parts you're you're going
- 29:27to do screw threading with you know
- 29:29either inserts or something of that
- 29:31nature. But for let's say for a large
- 29:33part where you have um you know a 2in um
- 29:39uh let's say a 2in diameter you know
- 29:42pipe or something like that where it
- 29:44just got to you know screw together.
- 29:46You're going to need the offsets on the
- 29:47surfaces to make those work.
- 29:49And it's not hard, but you better plan
- 29:52for it or you're going to be basically
- 29:54driving yourself nuts trying to fix it.
- 29:57>> Thanks again to Sean and his team at
- 29:59Replform taking the time to uncover all
- 30:02the secrets of electroplating 3D printed
- 30:04parts. There's some incredibly useful
- 30:07information here that you can reference
- 30:08back to as you take on your next
- 30:10electroplating project.
About this transcript
This page contains the full transcript of Plastic In. Metal Out. | Electroplating 3D Printed Parts for Metal Performance (Part 1) by MLC CAD Systems, generated from the public captions YouTube serves with the video. The transcript has 5,297 words across 787 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.