YouTube2Text

PCB Copper Pours 101 - Phil's Lab #176 — Transcript

by Phil’s Lab · 5,253 words · 776 segments · language en · Watch on YouTube

Full transcript

  1. 0:00In this video, I'd like to cover the
  2. 0:01basics of copper PS, polygon poles,
  3. 0:03fills, planelets as they relate to
  4. 0:06printed circuit board or PCB design.
  5. 0:08We'll cover the critical aspects of
  6. 0:10polygon poles and copper fills, when to
  7. 0:12use them, when not to use them, what
  8. 0:14they are for, and what to pay attention
  9. 0:16to, and how to try and avoid them
  10. 0:18causing issues and actually being a
  11. 0:19benefit to your design. The PCB you're
  12. 0:22seeing here utilizes quite a number of
  13. 0:24polygon pores and cover pores.
  14. 0:25Essentially, a copper pole is just a
  15. 0:27polygon fill that floods a part of the
  16. 0:29board area with copper and is assigned
  17. 0:31to a particular net. This is very very
  18. 0:33similar to these traces you're seeing
  19. 0:35here, but they serve different purposes
  20. 0:37and are typically quite a bit larger in
  21. 0:39terms of area and and then of course
  22. 0:41also volume. You might have polygon
  23. 0:43pores that span the entire board such as
  24. 0:46this top ground polygon paw. You might
  25. 0:48have smaller polygon pores that only
  26. 0:50span a small subsection and are used for
  27. 0:52instance for as larger current carrying
  28. 0:55traces or polygons. And you might see
  29. 0:57polygon pores or copper fields used as
  30. 1:00reference planes. For instance, for
  31. 1:01internal layers. In this particular four
  32. 1:04layer board, we have layer 2 and layer
  33. 1:05three. Those are essentially board
  34. 1:07spanning copper paws or polygon fills.
  35. 1:10Again, they are all respectively tied to
  36. 1:12their own net. A lot of the times this
  37. 1:14will be connected to ground or reference
  38. 1:17or 0 volt. So that for instance in this
  39. 1:19case on layer 1 when we have traces
  40. 1:21running on layer one the layer adjacent
  41. 1:23is a nice solid reference plane a
  42. 1:25reference copper pore which provides a
  43. 1:27low impedance return path when used as a
  44. 1:30reference plane. This is of course
  45. 1:32useful for the return path itself for
  46. 1:34EMI and signal integrity purposes. But
  47. 1:37polygon pores in general can provide far
  48. 1:39more uses than that. They can act as
  49. 1:42heat sinks. They can allow for thermal
  50. 1:43spreading. Can use them to balance the
  51. 1:45copper distribution across various
  52. 1:47layers and for our power distribution
  53. 1:49within our printed circuit board. For
  54. 1:51more information on stackup buildup and
  55. 1:53reference planes when you would use
  56. 1:55polygon PS for that and essentially in
  57. 1:57every PCB design you would do that. I
  58. 1:59can suggest checking out video number 56
  59. 2:01on my channel titled PCB stackup and
  60. 2:03buildup. And I also have a summarized
  61. 2:05article on resources.outium.com.
  62. 2:07Again links will be in the description
  63. 2:09box below. These polygon PS, these
  64. 2:11copper fills should never be used simply
  65. 2:13for decorative reasons. Every single one
  66. 2:16of these fills and PS has a particular
  67. 2:18reason for being there. They should
  68. 2:20never just been thrown on a board
  69. 2:21arbitrarily. There's always a use to
  70. 2:23them. And I'd like to show you again
  71. 2:25some of the basic dos and don'ts as a
  72. 2:27little starter guide to using polygon
  73. 2:28paws and what to watch out for. Again,
  74. 2:31this is a 101 or basics type video. If
  75. 2:33you'd like to go into a bit more depth,
  76. 2:34there are some great videos by Robert
  77. 2:36Ferin and Rick Hartley. for instance, to
  78. 2:38how to decide on a PCB layer ordering,
  79. 2:40pouring and stackup. Links will be in
  80. 2:42the description box below. And this
  81. 2:44video on the Alteium Academy YouTube
  82. 2:45channel called Secrets of PCB
  83. 2:47Optimization again with Rick Hartley,
  84. 2:49which goes more into the design for
  85. 2:50manufacturing aspects, which we will be
  86. 2:53covering in a tiny bit in this video as
  87. 2:54well. Again, links in the description
  88. 2:56box below. A huge thank you to Alum for
  89. 2:59sponsoring this video. I use Alim
  90. 3:00develop which includes Alum Design and
  91. 3:02Alim 365 in my everyday day-to-day work
  92. 3:05life as well as for creating content for
  93. 3:07this channel and also use out designer
  94. 3:09as part of Alton Develop to design and
  95. 3:11manufacture this digital audio
  96. 3:13processing board that we'll be seeing
  97. 3:15and using in this particular video. Out
  98. 3:17in develop enables multiddisciplinary
  99. 3:19teams to design, develop and manufacture
  100. 3:22high quality hardware products with ease
  101. 3:24and efficiency all the way from
  102. 3:25co-creation of designs be that parts
  103. 3:28library management, schematic design,
  104. 3:30hardware design, requirements
  105. 3:31management, all the way through managing
  106. 3:33your supply chain, manufacturing, and of
  107. 3:35course generating and maintaining all of
  108. 3:38the relevant data as part of an entire
  109. 3:40project. You can take a tour of Alton
  110. 3:42Develop and I'll leave links to this in
  111. 3:44the description box below which guides
  112. 3:45you through all of the parts that Alton
  113. 3:48Develop helps you manage in your project
  114. 3:50and product design process if you're
  115. 3:52interested. Again, I'll leave links in
  116. 3:53the description box below, but you can
  117. 3:55get started with Alton Develop and you
  118. 3:56can try this out for yourself risk-f
  119. 3:58free for 30 days. Links will be in the
  120. 4:01description box below. The first item
  121. 4:02I'd like to discuss when talking about
  122. 4:04copper paws is that of the pore settings
  123. 4:07as well as the design rules that relate
  124. 4:10to these polygon pores and copper fills.
  125. 4:12As with traces, pads, components, and
  126. 4:15any other feature that's on our printed
  127. 4:16circuit board, with polygon pores as
  128. 4:18well, and copper fills, regardless of
  129. 4:20which layer they are on, we need to
  130. 4:22adhere to certain design rules to make
  131. 4:24sure our printed circuit board is
  132. 4:25manufacturable, that we have minimal
  133. 4:27issues with assembly, hopefully none, of
  134. 4:29course, and of course that our Polygon
  135. 4:32PS aid our overall EMI performance and
  136. 4:35signature as well as signal integrity. A
  137. 4:37large part of that especially when with
  138. 4:39regards to manufacturability is that of
  139. 4:41clearance. So for instance I have this
  140. 4:43tiny 3.3 volt polygon pore here. This
  141. 4:46has certain clearance boundaries and is
  142. 4:48governed by certain clearance rules and
  143. 4:50constraints set in our design rules. So
  144. 4:52that could be the actual polygon to
  145. 4:54polygon clearance something around.35 mm
  146. 4:57here. This could be the clearance
  147. 4:59between the polygon pore and SMD pads to
  148. 5:02traces to traces within the ONET to
  149. 5:04features within the ONET and so on. You
  150. 5:07can find these rules under design rules
  151. 5:09in out designer and any ECAD tool will
  152. 5:11have these sets of rules. If I go to the
  153. 5:14clearance section, we can see we have a
  154. 5:15particular row for copper. So we have
  155. 5:17copper to track, copper to SMD pad,
  156. 5:19copper to thor pad, via and copper to
  157. 5:21copper as well as this single entry of
  158. 5:24copper to hull. Now, these all have to
  159. 5:26be set responsibly depending on your
  160. 5:28design constraints, depending on your
  161. 5:29manufacturer and manufacturability. I
  162. 5:32have a whole video on PCB design rules
  163. 5:34101. That's video number 170 on my
  164. 5:36channel. And again, I'll leave links to
  165. 5:37this in the description box below. And
  166. 5:39this goes more into detail of how to set
  167. 5:41up your design rules and how to assign
  168. 5:43them either locally or globally to the
  169. 5:44entire board. In essence, we want to
  170. 5:47make our PCB manufacturable not just for
  171. 5:49one manufacturer, but for a large subset
  172. 5:52of large group of manufacturers in
  173. 5:53general or without going near
  174. 5:55manufacturing minimum constraints and
  175. 5:57minimum levels. We want to make it
  176. 5:58reliably manufacturable with a high
  177. 6:00yield. That is when they are
  178. 6:01manufactured. A lot of the printed
  179. 6:03circuit boards survive without defects.
  180. 6:05If you go to your preferred manufacturer
  181. 6:07of choice, in this case I'm going to GLC
  182. 6:08PCB, they will always have a
  183. 6:10capabilities or manufacturing
  184. 6:11capabilities section. And from this you
  185. 6:13can then extract the design rules you
  186. 6:15need to use for your printed circuit
  187. 6:17board and also for your copper paws. Now
  188. 6:20they might be under the traces section
  189. 6:22because essentially traces are very very
  190. 6:24similar to copper paws. They have
  191. 6:26essentially the same clearance
  192. 6:27constraints between traces and copper
  193. 6:29fills and copper paws. So from this we
  194. 6:31can take minimum trace width minimum
  195. 6:33spacings which apply to both traces and
  196. 6:35copper features and and copper paws as
  197. 6:38well. And here GLC says they can go down
  198. 6:40to 0.1 millimeters for one and two layer
  199. 6:42boards and 0.09 mm for multi-layer
  200. 6:45boards above two. Now of course these
  201. 6:47are absolute minimum capabilities and
  202. 6:49I'd strongly suggest staying away from
  203. 6:51these if your design allows. And if you
  204. 6:54need to go to these minimum capabilities
  205. 6:56only do that locally wherever you need
  206. 6:58them on your printed circuit board
  207. 6:59design. Again refer to the design rules
  208. 7:01101 video how to set up local and global
  209. 7:03design rules. We always want to add on
  210. 7:05some sort of margin and set our design
  211. 7:07rules fairly straight. So not going down
  212. 7:09to these minimums. So this is for trace
  213. 7:11widths and spacing. Then there's going
  214. 7:13to be design rules such as the same net
  215. 7:15track to track spacing or copper feature
  216. 7:17to copper feature spacing in a layer via
  217. 7:20hole to copper clearance and so on. And
  218. 7:22these are again the absolute minimums
  219. 7:23that this particular PCB manufacturer
  220. 7:26can manufacture. In your e-car tool, you
  221. 7:28would then transfer these numbers over
  222. 7:29and add some sort of margin on top
  223. 7:31depending on what your design allows.
  224. 7:33Again, stay away from minimums. So, we
  225. 7:35have these clearance settings here. We
  226. 7:37also have minimum widths, which is also
  227. 7:39important for our copper features
  228. 7:41because, for instance, looking at this
  229. 7:431.2 volt copper paw, which essentially
  230. 7:46just distributes this 1.2 volt power net
  231. 7:48across parts of the board that has to
  232. 7:51neck down in certain areas. For
  233. 7:52instance, this area here, we can see we
  234. 7:54have a a narrower neck of about45 mm. If
  235. 7:58we were more constrained and we had to
  236. 8:00make this neck even smaller, we only
  237. 8:02want to do this necking down when we
  238. 8:04really really need to. We don't want to
  239. 8:06keep this current carrying or power
  240. 8:08carrying polygon paw narrower than we
  241. 8:10need to. And we always expand when we
  242. 8:11have the space. But in any case, even
  243. 8:14when we have to neck down, we have to
  244. 8:15stay above a certain minimum. So a
  245. 8:17similar rule that applies to traces, we
  246. 8:19have to go above a certain minimum trace
  247. 8:20width. Of course, also applies to copper
  248. 8:22paws as well. And having clicked on this
  249. 8:24polygon paw in the right hand side we
  250. 8:26can see various properties and one of
  251. 8:28these properties is this remove next
  252. 8:30less than feature. We also have this
  253. 8:32check box which says obey rules and
  254. 8:34that's obeys the rules we set out in our
  255. 8:36design rules. I can also uncheck that
  256. 8:38and say okay it needs to be larger than6
  257. 8:40mm. If I report that we can see
  258. 8:43immediately that this connection now
  259. 8:45breaks because alum or your ecad tool
  260. 8:47cannot connect this sliver here without
  261. 8:50violating the rule we set in place. So
  262. 8:52keep in mind also we need not just
  263. 8:55clearance rules but also minimum polygon
  264. 8:57pore width rules as well. And again only
  265. 8:59neck down when you really need to. These
  266. 9:01clearance and minimum copper paw width
  267. 9:04rules are in place of course to make
  268. 9:05this board manufacturable. If the
  269. 9:07features are too close to each other you
  270. 9:09might risk the chance of shorts from
  271. 9:11manufacturing tolerances. If you leave
  272. 9:14next too narrow they might not connect
  273. 9:16properly. You might have risk of
  274. 9:17breakages and so on. And in particular
  275. 9:19with higher voltage designs, you need to
  276. 9:21take into account your creepage and
  277. 9:22clearance requirements. So you might
  278. 9:24need larger clearances between various
  279. 9:26nets, especially if they're high voltage
  280. 9:28nets and so on. Another feature other
  281. 9:30than of course the clearances and the
  282. 9:32minimum widths are minimum island areas.
  283. 9:35On the right hand side, you might have
  284. 9:36already spotted this. We have this
  285. 9:38remove islands less than 5 square meters
  286. 9:40in this particular case. And we can
  287. 9:42change how small these islands can be.
  288. 9:44And this is particularly useful if
  289. 9:45you're doing polygon cleanup. And for
  290. 9:47example, you might want to remove small
  291. 9:50islands such as this if they're not
  292. 9:51stitched properly or if you cannot
  293. 9:53stitch them properly. We'll come to
  294. 9:54stitching beers later on as well. So
  295. 9:56there's various other parameters that we
  296. 9:58can use here. Your design rules you can
  297. 10:01set up depending on the layer they are
  298. 10:02on. So layer 2, layer three, because
  299. 10:04they're internal layers will likely have
  300. 10:07different constraints and different
  301. 10:09requirements to those that are poured on
  302. 10:11for instance outer layers. And this
  303. 10:12could be because pouring, for instance,
  304. 10:15if you're using controlled impedance
  305. 10:16traces such as the USB 2.0 and USB 3
  306. 10:20super speed differential pairs we have
  307. 10:21here, we want to keep a larger clearance
  308. 10:24away from these differential pairs to
  309. 10:26our polygon or copper paws because if we
  310. 10:29bring these planelets closer to these
  311. 10:31traces, that'll actually throw off the
  312. 10:33impedance of these traces. And for
  313. 10:35controlled impedance, you of course want
  314. 10:36to have them be the impedance you
  315. 10:38calculated them to be at. So, if I go to
  316. 10:40design rules, I've also set clearances
  317. 10:42for layer 1 and layer 4 that are
  318. 10:44slightly different to my inner layer
  319. 10:46clearance rules. Again, one reason being
  320. 10:48that I don't want them to be too close
  321. 10:50to my controlled impedance traces. Also,
  322. 10:53because we have multiple different
  323. 10:55polygon pores and little planets on the
  324. 10:58top and bottom layers. What is also
  325. 11:00important is the polygon paw order or
  326. 11:02priority. Which polygon pores do you
  327. 11:04want to pour first? In the case of layer
  328. 11:06one, I want to pour all these smaller
  329. 11:09polygons first and only apply my ground
  330. 11:12polygon paw that covers essentially the
  331. 11:13entire surface area of the top and
  332. 11:16bottom layers. I want to apply that last
  333. 11:18and that we can deal with priorities. If
  334. 11:20I go to tools, polygon paws, polygon
  335. 11:22manager, we can see I have a certain
  336. 11:24pore order. So I start with my smaller
  337. 11:26nets and only at the end I pour my
  338. 11:28ground polygon p. If I were to do my
  339. 11:31ground polygon port a different order
  340. 11:33and then repour all, you can see because
  341. 11:36the ground polygon pore takes priority,
  342. 11:38this Vbus Fnet or polygon pore is not
  343. 11:41poured correctly. That's why polygon
  344. 11:43pore priorities are very important and
  345. 11:45something you need to consider in your
  346. 11:47design as well. So this is it with it
  347. 11:48properly restored. Another large part
  348. 11:51when using polygon and copper PS is the
  349. 11:54discussion on thermal release versus
  350. 11:56direct connections. Direct connections
  351. 11:59are when you pour a polygon paw and as
  352. 12:01the name implies the polygon itself
  353. 12:04flows all over any features that are
  354. 12:07within that polygon paws area. So for
  355. 12:10instance here I have this pad and
  356. 12:12because this is a direct connection you
  357. 12:14can see the polygon pore easily flows
  358. 12:16all over that area encompassing the pad
  359. 12:19encompassing this other pad encompassing
  360. 12:21these v and so on. This is in contrast
  361. 12:23to thermal reliefs. For instance, a
  362. 12:26thermal relief. We can see for the
  363. 12:28ground polygon pore connected to these
  364. 12:30ground pads of for instance this 0603
  365. 12:33capacitor here. We have not the copper
  366. 12:36flowing all over the pad, but rather we
  367. 12:38have these little spokes that attach at
  368. 12:40suitable points from the polygon pore to
  369. 12:43this pad. And there's various reasons
  370. 12:45for doing one or the other. Direct
  371. 12:47connect would typically be preferred if
  372. 12:50it were to come with certain
  373. 12:51manufacturability issues. Direct connect
  374. 12:54is great because we have essentially a
  375. 12:56whole an entire connection to the
  376. 12:58relevant pad. We have better thermal
  377. 13:00conductivity between the various
  378. 13:02features that connect this polygon pore.
  379. 13:05But we have the issues that if we have
  380. 13:07copper imbalance, for example, if we
  381. 13:09have this large polygon pore, this large
  382. 13:12thermal mass of ground and then we
  383. 13:14connect that directly to a very small
  384. 13:16component just on one side and the other
  385. 13:18side of that component has just a
  386. 13:19relatively small thermal mass in terms
  387. 13:22of the copper area attached to it. That
  388. 13:24can lead to some severe
  389. 13:25manufacturability issues because again
  390. 13:27the ground here would act as a massive
  391. 13:29heat sink whereas the other side
  392. 13:31wouldn't have the same thermal mass. For
  393. 13:33example, if this small component would
  394. 13:34instead be just a solid connection, we
  395. 13:37have this large thermal imbalance, which
  396. 13:39means this ground pad number two doesn't
  397. 13:41heat up as quickly as our ground pad
  398. 13:44one. Now, this of course depends on the
  399. 13:46soldering methodology. If it's with an
  400. 13:47iron or reflow oven temperature profile
  401. 13:49and so on, but this can be a rather
  402. 13:52large issue in particular for smaller
  403. 13:54SMD components, that can lead to what's
  404. 13:57known as tombstone. So on one side
  405. 13:59because of the different connectivities
  406. 14:01and heat profiles either side of the
  407. 14:03component, the component might actually
  408. 14:05move up and sit up like a little
  409. 14:06tombstone, a little gravestone. That's
  410. 14:08of course a rather large manufacturing
  411. 14:10defect and something we would want to
  412. 14:12avoid. So therefore, instead of doing
  413. 14:14direct connections depending on the size
  414. 14:16of and difference between copper
  415. 14:17balances either side of the component,
  416. 14:19we might add these or typically add
  417. 14:21these thermal relieves. Now these
  418. 14:23thermal relieves other than just having
  419. 14:25a different essentially thermal
  420. 14:26connection will of course also change
  421. 14:28the inductive properties or the
  422. 14:30connection properties at these spokes.
  423. 14:32So a connection that has thermal
  424. 14:33relieves will typically have a higher
  425. 14:35inductance compared to earth solid
  426. 14:37connection. That can of course matter
  427. 14:39for decoupling and power delivery as
  428. 14:41well. The same principle applies also to
  429. 14:44through all connections. For example,
  430. 14:45here we have this through pad because
  431. 14:47either this will be wave soldered or
  432. 14:49manually soldered with a soldering iron.
  433. 14:51And if you have a a solid connection to
  434. 14:53all of these ground poles and planes, we
  435. 14:55have these essentially on four layers.
  436. 14:57If we had a solid connection here, that
  437. 14:59would be very very difficult to solder,
  438. 15:01especially if it's for hand soldering.
  439. 15:02But of course, it can also be helpful
  440. 15:04for wave soldering as well. So, we need
  441. 15:05to take this into account with copper
  442. 15:07paws for SMD components and also for
  443. 15:11through hole components. Now, there's
  444. 15:12always going to be a trade-off again for
  445. 15:14thermals, for inductance, and
  446. 15:15solderability, manufacturability. That's
  447. 15:17something you have to keep in mind too.
  448. 15:18What is the component connected to? What
  449. 15:20is the pin connected to? And for
  450. 15:22instance, for these SMD components, what
  451. 15:24are the other pins connected to? Is
  452. 15:25there thermal imbalance? Is there copper
  453. 15:27imbalance? And so on. As a very very
  454. 15:29general guideline, I would suggest using
  455. 15:31thermal relieves, especially if you're
  456. 15:33doing these large ground polygon pores
  457. 15:35and floods on your top and bottom
  458. 15:37layers, especially if you have these
  459. 15:39rather large imbalances between one side
  460. 15:41of the component and the other. Now, of
  461. 15:43course, this can also be the case for
  462. 15:44multi-pin components, more than two
  463. 15:46pins. Again, check your copper balances.
  464. 15:48Check the way this board is being
  465. 15:50assembled and manufactured. But again,
  466. 15:52polygon poles, copper fills can act
  467. 15:54great as heat sinks, and that's often
  468. 15:56times what's wanted. So, for instance,
  469. 15:58for this QFN exposed pad in the center,
  470. 16:00that's connected to all of the ground
  471. 16:03copper that exists on the board, at
  472. 16:05least locally around it. That is very
  473. 16:07useful as a heat sink. But again, there
  474. 16:09are manufacturing challenges with
  475. 16:10assembly that come with this. There's
  476. 16:12always a balance in terms of how these
  477. 16:14spokes are sized. These thermal relief
  478. 16:16spokes are sized. You can go with an IPC
  479. 16:19guideline for this. This of course
  480. 16:21depends on the pad size, what kind of
  481. 16:24current and power demands you have
  482. 16:26flowing into and out of that component,
  483. 16:27what inductance requirements you have,
  484. 16:29and so on. But as a general rule of
  485. 16:31thumb, you would take if it's a if it's
  486. 16:34a square pad, you would take a pad side.
  487. 16:37So if that's 1 millm, take 60% of that
  488. 16:40and then divide by the number of spokes
  489. 16:42you have connecting to this. So a 1
  490. 16:44millm pad, a 1 millm square pad would
  491. 16:47give 0.6 mm. If you have two spokes,
  492. 16:50that would be 0.3 mm. If you have four,
  493. 16:52that would be 0.15 mm spoke width.
  494. 16:55Again, this depends on current. It
  495. 16:56depends on the pad shape, pad size. But
  496. 16:58that's a general rule of thumb. You can
  497. 17:00check out the IPC 2221 and 2222
  498. 17:04standards for more details on this.
  499. 17:07Thermal relieves exist for both SMD
  500. 17:09pads, throughhole pads, but of course
  501. 17:11for VAS themselves. And you've probably
  502. 17:13seen here my VA do not have any thermal
  503. 17:17relieves on them. And this is what I
  504. 17:19would suggest as an as a complete
  505. 17:20default. I don't think I've ever used
  506. 17:22thermal relieves on VAS. The way you can
  507. 17:24set that up depends on your ECAD tool as
  508. 17:26well. If we go to design rules, then go
  509. 17:28to polygon connect. There is the simple
  510. 17:30constraints option where everything just
  511. 17:32has a certain style. So it's relief
  512. 17:34connect, direct connect. But I go with
  513. 17:36advanced and I can change my thermal
  514. 17:38relief properties depending on the
  515. 17:40connection type. So that's through hole
  516. 17:41pad, if it's SMD pad, or if it's a V
  517. 17:44connection. Here you can set the air gap
  518. 17:46width as well as the conductor width and
  519. 17:48how many conductors you have. Again,
  520. 17:49either follow this 60% rule divided by
  521. 17:52the number of conductors or generically
  522. 17:54I typically leave that if I don't have
  523. 17:56any particular requirements for 0603ish
  524. 17:58components at about 3.3 or 0.25.25 25
  525. 18:02for SMD pads and similarly for
  526. 18:04throughhole pads. That is a pretty good
  527. 18:07starting point I found. Also for hand
  528. 18:09soldering but via connections again I
  529. 18:11would personally always leave as direct
  530. 18:13connect unless there's a very very good
  531. 18:15reason to do otherwise. Now of course
  532. 18:17other than global rules you can set them
  533. 18:19per pad. So if I click on a certain pad
  534. 18:21here go to the properties on the right
  535. 18:22hand side you can see I can click on
  536. 18:25relief and I can change the relief to
  537. 18:26whatever I want for that particular pad.
  538. 18:29So you can set them individually for
  539. 18:30pads. And of course, you can create your
  540. 18:32own custom design rules that pick out
  541. 18:34certain pads if they are have these
  542. 18:36certain dimensions, then apply a certain
  543. 18:37relief like so or like so. So you don't
  544. 18:40have to use just just this one certain
  545. 18:42overall design rule. What you've
  546. 18:45probably also really noticed is the
  547. 18:47amount of these grounded vas that are
  548. 18:49scattered seemingly around the board.
  549. 18:51Those are what's known as stitching vas.
  550. 18:53And these are very very important
  551. 18:56particular if you have multiple same net
  552. 18:58polygon pores around the board. These
  553. 19:02VAS are placed at certain intervals and
  554. 19:04certain spacings all across the board
  555. 19:07anytime we have a polygon paw and they
  556. 19:09tie all of these ground fills and ground
  557. 19:13paws together again at somewhat regular
  558. 19:15intervals along the Z axis. So, so
  559. 19:18vertically, if we do this side on view,
  560. 19:20we can see all these stitching views all
  561. 19:22around the board that tie all of these
  562. 19:25planes and copper fills of one
  563. 19:27particular net together. There are
  564. 19:29plenty of reasons for this. One of the
  565. 19:31reasons is that for every single ground
  566. 19:34pad of top and bottom layer components,
  567. 19:36we want to tie this pad with a low
  568. 19:39impedance, low inductance connection to
  569. 19:41the internal reference to the internal
  570. 19:43ground planes again to lower the
  571. 19:45impedance of that connection. So part of
  572. 19:48these grounded VAS are just simply the
  573. 19:50the via connection to the internal
  574. 19:52planes for all of these top and bottom
  575. 19:54layer ground connections. But the
  576. 19:57remaining connections which aren't next
  577. 19:58to these ground pads are again also
  578. 20:00these stitching behind
  579. 20:06into the RF and high frequency bands
  580. 20:08that tie all of these polygon PS
  581. 20:11together to maintain a low impedance
  582. 20:13across a large bandwidth. In the
  583. 20:14previous video on the channel on via
  584. 20:16fencing and edge plating, I go into a
  585. 20:18bit more detail on via stitching, but we
  586. 20:20have them around the perimeter. But
  587. 20:22again tying all the copper polygon paws
  588. 20:24together to maintain this lo pins
  589. 20:26connection throughout all of these
  590. 20:28ground polygon paws and planes and
  591. 20:31layers. If we didn't have these
  592. 20:32stitching VAS for instance if I had this
  593. 20:35region like so where I basically just
  594. 20:37have the ground v next to the ground
  595. 20:39pads we have this unconnected polygon
  596. 20:42pore here. And this pore if not stitched
  597. 20:44properly and stitched correctly can
  598. 20:46actually resonate and essentially form
  599. 20:48an antenna because it's only fed very
  600. 20:50simply speaking by the left hand side
  601. 20:52and the right hand side here is
  602. 20:55essentially floating at RF without these
  603. 20:58stitching VAS. So we place these
  604. 21:00stitching VAS down also for EMI and
  605. 21:02signal integrity reasons that we don't
  606. 21:04get these unwanted resonators. The
  607. 21:06larger the pore, the larger these
  608. 21:08resonant planes and resonant areas
  609. 21:10without stitching, the lower the
  610. 21:12resonant frequency will be typically for
  611. 21:14these patches and these essentially form
  612. 21:16little patch antennas. The simple rule
  613. 21:19of thumb for spacing is analyzing the
  614. 21:21maximum frequency of interest in your
  615. 21:23design. So if that's analog, that's very
  616. 21:25straightforward. V equals lambda F. But
  617. 21:27for digital, we want to correlate the
  618. 21:29rise and fall times of our digital
  619. 21:31signals to an approximate knee
  620. 21:32frequency. So our somewhat of an analog
  621. 21:35bandwidth. We figure out the maximum
  622. 21:36frequency. We calculate the wavelength.
  623. 21:38Of course, taking into account the speed
  624. 21:40of light and the reduction of the speed
  625. 21:41because of the dilectric material. And
  626. 21:43then we take that wavelength and divide
  627. 21:45that by some sort of constant. So that
  628. 21:47could be eight. But if we want to be
  629. 21:48very stringent in that we divide by 20.
  630. 21:50So the wavelength divided by 20 might be
  631. 21:53a very very strict stitching via
  632. 21:55approach. And we do that all across the
  633. 21:57plane all across the board wherever we
  634. 21:59have these polygon PS.
  635. 22:02This is something I typically do at the
  636. 22:04end of the board. But I try to plan in
  637. 22:06stitching views while I do the design.
  638. 22:08You don't want to be left with loads of
  639. 22:10areas of polygon poles that aren't
  640. 22:12stitched properly. Now, areas that you
  641. 22:14can't stitch properly, what you can do,
  642. 22:16for example, if we have this region
  643. 22:18here, which isn't providing terribly
  644. 22:20much use, what we can do is add in a
  645. 22:22polygon paw cutout. So, I can press P
  646. 22:24and then go to polygon paw cutout and
  647. 22:26just very simply drawing. I can draw
  648. 22:28this cutout area very badly drawn, but
  649. 22:30something like this. And you can see
  650. 22:32that gets rid of this polygon pore here
  651. 22:35in case we want to do some polygon paw
  652. 22:37cleanup. In case you don't want to
  653. 22:38stitch, we could add in these little
  654. 22:40regions. And these could be multi-layer.
  655. 22:41These can be per layer depending on
  656. 22:44where you place these regions. And
  657. 22:45that's what I typically do at the end is
  658. 22:46also this polygon pore cleanup using
  659. 22:48these polygon pore cutouts. Now the
  660. 22:50question is, is there actually any
  661. 22:52benefit to pouring top and bottom layer
  662. 22:54copper? Often times you can actually
  663. 22:56make things worse by pouring your signal
  664. 22:58and power layers with copper, especially
  665. 23:00if it's uncontrolled. So if you're not
  666. 23:02doing the stitching appropriately, if
  667. 23:03you're not cleaning up these polygon
  668. 23:05layers appropriately, if you're letting
  669. 23:07the polygon pors get too close to your
  670. 23:09controlled impedance traces and so on,
  671. 23:11you can actually mess things up. So
  672. 23:13often times a guideline is to simply on
  673. 23:15these outer layers or these signal
  674. 23:16layers to not pour any copper. However,
  675. 23:19arguments against that are copper
  676. 23:21balancing. So if we have uneven copper
  677. 23:23distribution between layers, so across
  678. 23:25the Z axis or even in parts along the XY
  679. 23:29plane, if we have uneven copper
  680. 23:31distribution, that can lead to
  681. 23:33manufacturing risk because the copper
  682. 23:35and the actual dialectric material, the
  683. 23:37fiberglass, they have different
  684. 23:39coefficients of thermal expansion. So
  685. 23:41during manufacturing, during pressing,
  686. 23:43also during assembly, the different
  687. 23:45materials in your printed circuit board
  688. 23:47will expand at different rates. But by
  689. 23:49keeping the copper distribution even and
  690. 23:50balanced across the boards in all axes
  691. 23:53and along all axes, we can somewhat
  692. 23:56mitigate this warping and bending of the
  693. 23:58board during manufacturing. Now although
  694. 24:00quite exaggerated copper balance issues
  695. 24:03can lead to increased bow and twist of
  696. 24:06the boards. Now all these pictures are
  697. 24:08somewhat exaggerated. Maybe not this
  698. 24:10one. You can see there's quite a bit of
  699. 24:12arching in the board and that can of
  700. 24:14course lead to reliability issues where
  701. 24:16you get cracking in the copper itself
  702. 24:18and of course issues with assembly. If
  703. 24:20you need a certain planarity, a certain
  704. 24:21flatness of your printed circuit board.
  705. 24:23So that's why copper balance is
  706. 24:24important. Now if you don't want to do
  707. 24:26that, I'd suggest talking to your
  708. 24:27manufacturer and talk about if your
  709. 24:29board is manufacturable as such without
  710. 24:30these copper paws on the signal layers
  711. 24:32and without copper balancing. Often
  712. 24:34times manufacturers will also add in
  713. 24:35copper thieving themselves, but it's
  714. 24:37something you should really discuss with
  715. 24:38your manufacturer. On that topic, I'd
  716. 24:40really strongly suggest watching the
  717. 24:41secrets of PCB optimization video by
  718. 24:43Rick Hartley, which goes into more
  719. 24:45detail on copper balancing and why that
  720. 24:46is needed. These days, I typically pour
  721. 24:48crop on all layers, but that does mean
  722. 24:50it takes me quite a lot of time to just
  723. 24:52clean up these polygon PS, make sure the
  724. 24:54stitching is appropriate, make sure I've
  725. 24:56kept my polygon pors away from all
  726. 24:59sensitive circuitry such as controlled
  727. 25:00impedance traces and so on. But that is
  728. 25:03my personal approach and it depends on
  729. 25:04board to board. There is no generic
  730. 25:06blanket statement for this. If you do
  731. 25:08have unstitched areas, again you can use
  732. 25:10these polygon pore cutouts, but you can
  733. 25:12also go to the polygon properties itself
  734. 25:14and check the remove islands section.
  735. 25:16Always I would suggest check the remove
  736. 25:18dead copper section. Lastly, just for
  737. 25:21the sake of completeness, you might have
  738. 25:22heard of hatched and solid fills
  739. 25:25typically for rigid printed solid fills
  740. 25:28is what you would use here. And as we
  741. 25:30can see here, the option for hatched is
  742. 25:33available pretty much in any e-cat tool.
  743. 25:34If we go to the properties, click on
  744. 25:36hatched, we can see it looks hatched.
  745. 25:38There are different hatching methods.
  746. 25:40So, horizontal, we can do vertical, 45°
  747. 25:43and 90° and so on. And this is, at least
  748. 25:46in my opinion, predominantly just used
  749. 25:49in flexible printed circuit boards where
  750. 25:51along the bend line of the flexible
  751. 25:53printed circuit board, you might want to
  752. 25:55use a hatch plane to reduce the risk of
  753. 25:57cracking and to make the board easier to
  754. 26:00bend along that certain bend line. for
  755. 26:03so for rigid PCBs, I would pretty much
  756. 26:04always just use solid copper fills. But
  757. 26:07then for flex PCBs or rigid flex PCBs,
  758. 26:11you typically want to use these hatched
  759. 26:13copper fills again to try and avoid
  760. 26:16cracking during bending and improve the
  761. 26:18mechanical flexibility of your flex
  762. 26:20printed circuit board. So again, just
  763. 26:22stick with solid for your rigid PCBs.
  764. 26:25Thank you very much for watching this
  765. 26:26video. I hope it was useful and I hope
  766. 26:28it showed you the basics of what to pay
  767. 26:30attention to when using copper balls and
  768. 26:32copper fills on your own printed circuit
  769. 26:34board designs. If you like the video,
  770. 26:35please leave a like, a comment if you
  771. 26:37have any questions, and don't forget to
  772. 26:38subscribe to stay up to date with any
  773. 26:40latest PCB design, hardware design, and
  774. 26:42embedded systems videos. Thanks again
  775. 26:44for watching, and I hope to see you in
  776. 26:45the next one. Bye-bye.

About this transcript

This page contains the full transcript of PCB Copper Pours 101 - Phil's Lab #176 by Phil’s Lab, generated from the public captions YouTube serves with the video. The transcript has 5,253 words across 776 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.