OM642 Mercedes 3.0 Full Deleted Back Pressure Exhaust Sensor / Test / How to Test any Sensor — Transcript
Full transcript
- 0:00what's up youtube this is clay with the
- 0:01clay way here in muskegon michigan and
- 0:04today we've got a 3.0
- 0:07mercedes-benz
- 0:09crd diesel here in the shop deleted
- 0:12we did the oil cooler on it we did block
- 0:15offs on the intake and stuff like that
- 0:17and when we got all done
- 0:18it had a code for a b60 exhaust gas
- 0:22pressure sensor
- 0:24so
- 0:26i figured out that
- 0:28maybe i broke the pressure sensor but it
- 0:30gave me a good opportunity to show you
- 0:32folks how to check these pressure
- 0:34sensors and let you know that most
- 0:36sensors work
- 0:38identically to this one if they're a
- 0:39three wire sensor they generally send in
- 0:42five volts from the computer
- 0:45they have a ground from the computer
- 0:48and they send back a signal to the
- 0:50computer saying hey
- 0:52i'm working
- 0:54and in this situation i don't believe
- 0:56it's sending back a signal that says hey
- 0:59i'm working
- 1:00so what we're going to do today is i'm
- 1:02going to show you this i'm going to show
- 1:04you a diagram explain it to you in
- 1:06layman's terms so simple people like me
- 1:09can understand
- 1:11without having a bunch of expensive
- 1:12equipment
- 1:14now the test that i'm gonna do in this
- 1:16video require that i unplug the
- 1:18electrical connector on the top of the
- 1:20sensor and i'm gonna show you that here
- 1:21in a couple moments
- 1:25so all we're going to need to do this is
- 1:27a digital multimeter
- 1:29uh a couple of alligator clips and i've
- 1:31got two separate kind of alligator clips
- 1:33i got one black one one green one
- 1:34doesn't matter what color it is it's
- 1:36wired wire
- 1:37and i'm gonna use these terminal keys
- 1:40to probe into the wire terminals to test
- 1:44for the voltages that i need and we're
- 1:46going to do some simple fundamental
- 1:48tests
- 1:49on this thing and show you how it works
- 1:51and this will lead you into other
- 1:53avenues of when you're testing other
- 1:55three wire circuits
- 1:56like i said they generally just send in
- 1:58voltage and send out voltage and they
- 2:01tell the computer what it's doing based
- 2:03upon the voltage
- 2:05now we need to understand how this
- 2:07sensor works
- 2:08and
- 2:09how it operates
- 2:11so first off we need to look at the
- 2:13diagram we're going to notice by the
- 2:15diagram that it has one two three wires
- 2:20one is for five volts
- 2:23one is for ground
- 2:25and one is for output sensing
- 2:29to recognize the fluctuation of the
- 2:32diaphragm in the sensor now as air
- 2:34travels up into this hole on the back
- 2:37side it's going to fluctuate that
- 2:38voltage
- 2:40to the ecm if it's working properly when
- 2:43we're looking at this sensor we're going
- 2:44to consider this top portion home which
- 2:48is actually the number three ground
- 2:50this outside portion which is the white
- 2:52wire is going to be our sensing wire
- 2:55which sends signal back
- 2:58to the ecm which is going to be on our
- 3:00right side our left side panel is going
- 3:03to be our 5 volts reference
- 3:06from the computer and with the key
- 3:08turned on that should always have 5
- 3:10volts reference
- 3:14so with our key turned on and all of our
- 3:16indicator lights illuminated without the
- 3:18engine running we should be able to
- 3:20check the wire for 5 volts reference it
- 3:23is important to do all of these checks
- 3:25if you don't do them you may get a
- 3:27misdiagnosis
- 3:30okay so for our first test we're gonna
- 3:32hook our
- 3:34ground lead up to a ground right there
- 3:38and we're gonna take our plug off and
- 3:40using the red wire on the back side
- 3:46we're going to barely touch inside there
- 3:47we're not going to damage anything by
- 3:50slamming this in there now with that
- 3:52inserted in there we should have about 5
- 3:54volts which is 4.9
- 3:57and that is correct that's telling us
- 3:59that our ecm is sending a signal
- 4:02down to
- 4:04the sensor
- 4:05now we want to make sure that we're not
- 4:07on something conductive
- 4:10so it doesn't short out
- 4:11now taking our positive lead and hooking
- 4:14it up to a constant 12 volt source
- 4:18and then taking our ground lead
- 4:20and hooking it up we're going to check
- 4:22for ground and make sure that we don't
- 4:24have a bad ground system
- 4:26and it's sending ground to our sensor
- 4:30now with that pushed in there we should
- 4:32have battery voltage because battery
- 4:34voltage is the same over here
- 4:37which is why we don't have 4.9 volts and
- 4:40we only have 11.5 now most of you folks
- 4:43are not going to have the shroud off of
- 4:45here which is no big deal you should
- 4:47still be able to remove the sensor even
- 4:48with the shroud on here
- 4:51but we need to first disconnect it and
- 4:54how we're going to do that is we're
- 4:56going to push on the little rocker right
- 4:57here at the top
- 4:59right there where my thumbnail is
- 5:01and if it doesn't come off push it
- 5:03downward and pull it up sharply with the
- 5:06rocker pulled back that goes for just
- 5:09about any sensor
- 5:12now we're going to take a 27 millimeter
- 5:15and we're going to unscrew this
- 5:17and you should be able to get up
- 5:18underneath here with the 27 millimeter
- 5:21and unscrew it
- 5:23and in some situations this could be
- 5:25unscrewed with the 15 16 just depends on
- 5:27the model of what you're working on
- 5:31be careful when you go to pull this out
- 5:33there is a seal on here that could get
- 5:36lost so make sure you have that on your
- 5:38new one if you end up replacing it now
- 5:40all multimeters have what's called
- 5:42continuity it's this little symbol right
- 5:44here and what happens when you turn a
- 5:47multimeter onto continuity is when two
- 5:50wires are connected
- 5:54it will emit a noise meaning that you
- 5:56have a connection between the two wires
- 5:59so that's why our
- 6:02multimeter has a battery inside it
- 6:04because it sends a signal through the
- 6:06wire and it says hey
- 6:08i'm connected and i've bridged a joint
- 6:11so this is basically telling you that
- 6:14all this power is being sent through
- 6:16this wire and you don't have a broken
- 6:17wire in the center of there
- 6:19continuity tests are probably one of the
- 6:21most important tests with electrical
- 6:23because it tells you if you have a break
- 6:25somewhere now this next test is going to
- 6:27tell us that
- 6:29we have a bad sensor but
- 6:32we don't want to stop here without doing
- 6:34the very last test so keep that in mind
- 6:37now we're testing for continuity so we
- 6:39still have it set at continuity we have
- 6:41one of our alligator clips hooked here
- 6:44and we have the other end of that outer
- 6:46alligator clipped hooked to our home
- 6:49which is our ground which is post number
- 6:51three and when generally when you touch
- 6:54the outside of this
- 6:55we should have continuity meaning this
- 6:58should be
- 6:59grounded out but it's not and that
- 7:01pretty much tells us that the sensor is
- 7:03bad but we still want to make sure
- 7:05that it's not sending voltage back to
- 7:08the ecm and that's not being what's
- 7:10being received because
- 7:11it could just ground out through this
- 7:13and because the ecm actually sends a
- 7:16ground i could be mistaken but i want to
- 7:18make sure that it's actually bad
- 7:21well apparently
- 7:22uh i left my battery or left my switch
- 7:25on on my
- 7:27multimeter so i'm gonna have to use the
- 7:29power probe and the power probe is great
- 7:31and it does a continuity test just like
- 7:33the
- 7:35just like the meter does because when
- 7:36you take this it's the same thing so now
- 7:38we're gonna test this new part
- 7:41and
- 7:42see if it actually reads ground
- 7:45like the other one was supposed to now
- 7:47with our alligator clip connected to our
- 7:50home in there we'll touch the body and
- 7:52get ground
- 7:56which we do so we know this sensor is
- 7:58good and our other one was bad
- 8:00so for the very last test
- 8:02okay for this portion of the test we've
- 8:05got one alligator connector to a ground
- 8:09that's ran into our ground side of our
- 8:11voltage meter our voltage meter is set
- 8:14on 200 volts dc
- 8:16now with the sensor installed and the
- 8:19engine running we should get 0.5 volts
- 8:22or higher
- 8:24now very carefully we've inserted our
- 8:26probe down in there and hooked our black
- 8:28alligator clip to our positive side of
- 8:30our voltage meter
- 8:33now this is our let's say output side
- 8:36which is the white wire which
- 8:38sends the voltage signal as the vehicle
- 8:40is running
- 8:41to the ecm
- 8:43now with my sensor plugged back in
- 8:46i work my throttle and my voltage should
- 8:48change but it's not so this tells us
- 8:50that we have a defective sensor and it
- 8:52needs replacing now no matter what it is
- 8:54you're doing in life
- 8:56if anyone else can do it i promise you
- 8:58you can do it too
- 9:00hopefully you folks get this and it
- 9:02makes sense to you i tried to make it as
- 9:04easy and as laymen as possible because
- 9:06not everybody knows this stuff i had to
- 9:09learn it so hopefully you learned a
- 9:11little bit of something too a lot of
- 9:12vehicles work under this principle when
- 9:15they're using switches and sensors like
- 9:17this so if it has three wires on it you
- 9:19pretty much know how to test it no
- 9:21matter what it is
- 9:22god bless folks have a great day
About this transcript
This page contains the full transcript of OM642 Mercedes 3.0 Full Deleted Back Pressure Exhaust Sensor / Test / How to Test any Sensor by The Clay Way, generated from the public captions YouTube serves with the video. The transcript has 1,586 words across 248 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.