YouTube2Text

O"G, Inverter PCB Repairing communication error — Transcript

by Electric Locha · 1,576 words · 216 segments · language en · Watch on YouTube

Full transcript

  1. 0:00So, 1, 2, 3, 4, 5, the whole scene is
  2. 0:02about these five pins. Jai Hind friends
  3. 0:06, my name is Raj and you are watching
  4. 0:08our YouTube channel Electric Locha. You
  5. 0:11can see we have set this up here; these
  6. 0:14are motors, two outdoor motors, an
  7. 0:16indoor motor, and this is an O General
  8. 0:19PCB. This O General PCB is having this
  9. 0:22problem. Its timer LED blinks twice, as
  10. 0:26the customer told us. And this is its
  11. 0:29indoor unit, friends. You can see it's
  12. 0:31a small-sized one, that's the PCB, it's
  13. 0:33small-sized. And we have connected a
  14. 0:36compressor to it. Let's turn it on and
  15. 0:38see what actually happens with it.
  16. 0:40Whether the motor runs or not, or
  17. 0:42whether the compressor starts or not.
  18. 0:45Do both motors run? What actually
  19. 0:47happens? What is its condition? Because
  20. 0:49the customer only told us about the
  21. 0:50error. So for now, we will turn it on
  22. 0:53and see what error it gives. You can
  23. 0:57see. The indoor motor has just started
  24. 1:00running. And what happens in this PCB?
  25. 1:03First, power goes to the indoor unit
  26. 1:05and then the relay turns on here. Then
  27. 1:08power comes to the outdoor unit. You
  28. 1:13just saw its outdoor unit turn on. The
  29. 1:16relay in the outdoor unit has also
  30. 1:18turned on, let's see. Now you can see
  31. 1:26it is giving a two-blink error. It will
  32. 1:28do it again. It takes a little time to
  33. 1:31do it. Did you see? A two-blink error
  34. 1:35is appearing here. Now friends, we will
  35. 1:42try to repair it. Let's see what turns
  36. 1:45out to be faulty in it. Now friends, we
  37. 1:47will check the communication. We
  38. 1:50already have its board kept here. So,
  39. 1:54we will first check the communication
  40. 1:56using a UVW tester. Because as I told
  41. 1:59you before, The UVW tester checks the
  42. 2:06communication of General ACs and Daikin
  43. 2:09ACs well, especially the ones with
  44. 2:11modules. So you can see here, this is
  45. 2:16neutral and here is the signal. We will
  46. 2:20connect it here. And we will connect
  47. 2:25the other one here. You can see we have
  48. 2:29connected red to communication and
  49. 2:31black to neutral, and we will turn it
  50. 2:33on and wait for it to start. In this
  51. 2:37PCB, friends, the outdoor unit turns on
  52. 2:39after a little while. So let's see if
  53. 2:41communication happens from both sides
  54. 2:43or not. Here you can see there is data
  55. 2:46in, so it will show the indoor data
  56. 2:49here, and this will show the outdoor
  57. 2:51data. The fan motor in the data out has
  58. 2:54just started, friends. You can see it
  59. 2:58there in the corner. You can also see
  60. 3:08its connector here. The connector is
  61. 3:11small too. It's a three-pin connector.
  62. 3:22You can see this, friends. Yes. Look
  63. 3:26here, this LED is glowing. The data
  64. 3:30from the indoor unit is coming through.
  65. 3:33But the data from the outdoor is not
  66. 3:35coming. So, there is a communication
  67. 3:37fault, although the PCB is on. Let's
  68. 3:40see what the defect is in the
  69. 3:42communication. It's not sending outdoor
  70. 3:46data because the outdoor LED isn't
  71. 3:49glowing, so the outdoor module isn't
  72. 3:52sending data. This is its communication
  73. 3:56module. It’s a very simple module. If
  74. 4:01you comment, we will explain how it
  75. 4:03works another time. And how you can
  76. 4:08install a custom module if it goes bad.
  77. 4:12For now, let's see. Right now, friends,
  78. 4:16you can see this pin number one, what
  79. 4:19is it? Let's check it with a multimeter
  80. 4:24. So, let’s take the multimeter and
  81. 4:29set it to continuity. As you can see,
  82. 4:36let's check from here. First, the
  83. 4:39negative and positive go in, so let's
  84. 4:42see its pinout first. Only then will we
  85. 4:45check it accordingly. So, you can see
  86. 4:54this, friends. From here, this third
  87. 4:57pin. Pin number three is ground. And
  88. 5:00this one then should be VCC, 5 volts.
  89. 5:06The meter turned off. So, you can see
  90. 5:14this is 5 volts. This pin here is our 5
  91. 5:19volts.
  92. 5:20And this one is our TX pin.
  93. 5:24For sending data, for data out. And
  94. 5:27this one is ground. And then this pin,
  95. 5:32pin number two, is for zero crossing.
  96. 5:36And this pin number one is for
  97. 5:38receiving data. It is the RX pin. Let's
  98. 5:40look again. This is the RX pin and this
  99. 5:43is the zero crossing pin, number two.
  100. 5:46And this is the ground pin, number
  101. 5:47three. And this is the data sending pin
  102. 5:52, TX, and this pin is again 5 volt
  103. 5:54positive. So here, friends, you can see
  104. 5:59that pin number four has no print on
  105. 6:01this side. No print is going here
  106. 6:04either. No print is going here either.
  107. 6:07So its print must be on the other side
  108. 6:09and this pin should be the TX. Let's
  109. 6:12see. You can see its pin number four
  110. 6:15here and this is pin number five. The
  111. 6:17print for pin number four is coming
  112. 6:20here to the 2003 IC. So, friends, you
  113. 6:25can see this is the module's pin number
  114. 6:29four. The print comes directly here.
  115. 6:35Pin number 15 is the ULN 2003 IC
  116. 6:39installed here. So, what about the
  117. 6:43connectivity here now? It outputs
  118. 6:46directly, friends. This IC is built on
  119. 6:49a Darlington circuit. When we look here
  120. 6:53at this print. Now this is the output.
  121. 6:56If this is the transistor's collector,
  122. 6:58then this is the base. It's as simple
  123. 7:00as that. So, friends, we see here that
  124. 7:04pin 15 is its output. And its input is
  125. 7:08pin number two. So you can see pin
  126. 7:11number two goes here. Let's see where
  127. 7:14it is going. We place one probe here
  128. 7:19and check pin 32 with the other. So you
  129. 7:24can see it is connected to pin 32. And
  130. 7:27you can see it is connected to 32 here
  131. 7:30as well. So this is the data sending
  132. 7:34pin that will send data from here. Then
  133. 7:37the 2003 transistor will send the data
  134. 7:41forward, and the couplers on the module
  135. 7:45will send it further. This means this
  136. 7:48IC could be faulty. So, friends, let's
  137. 7:50replace this IC. Then let's see what
  138. 7:53happens. First, we will remove the 2003
  139. 7:57IC. As you can see, the IC has been
  140. 8:04removed. So, friends, we will install a
  141. 8:08new IC here. This is the ULN 2003 IC.
  142. 8:17Now, friends, we will power it on and
  143. 8:19first check the communication with the
  144. 8:21UVW tester. You can see we are turning
  145. 8:26on the UVW tester. Connect neutral to
  146. 8:29neutral. It works well in general cases
  147. 8:32. It is not that you can check all
  148. 8:34boards with this. But in general, it
  149. 8:37works very well. It is very good; we
  150. 8:40have powered it on. And we will connect
  151. 8:43its UVW here as well, friends. This is
  152. 8:48its UVW output. You can see it right
  153. 8:50here. So we will connect the UVW here
  154. 8:54so that if it gives an output, we will
  155. 8:56know. If it doesn't give any, that's
  156. 8:59fine. Then we will see what other
  157. 9:01problem there might be. Right now, only
  158. 9:02the indoor unit has turned on, friends.
  159. 9:04It takes a little time. First, the
  160. 9:07indoor unit turns on, and just like
  161. 9:09other non-inverter PCBs used to give CP
  162. 9:12, it gives CP and simultaneously
  163. 9:14provides communication too. Now you can
  164. 9:19see the board has turned on and you can
  165. 9:22see both data signals are being
  166. 9:23transmitted. Data is happening in both
  167. 9:27"in" and "out" now. So we changed this
  168. 9:302003 IC and this solved the
  169. 9:33communication problem. The outdoor
  170. 9:36motor has started. You can see here
  171. 9:38that the outdoor motor has started. And
  172. 9:42now you can see that the output has
  173. 9:43also arrived. The output is here in
  174. 9:45this. Let me show you from up close.
  175. 9:48The compressor output has arrived.
  176. 9:50Communication is also happening. The
  177. 9:52output has arrived as well. And it is
  178. 9:56attempting for quite a while. To
  179. 9:58provide the output. We will turn it off
  180. 10:00. Let's analyze the data. Whether the
  181. 10:03full output has come or not. Whether
  182. 10:05the correct output has come or not. So
  183. 10:07we have turned off the PCB. And now you
  184. 10:11will be able to see. Friends, now you
  185. 10:14can see that the complete output has
  186. 10:16arrived in the UVW. So now we will try
  187. 10:19running the compressor on it. Now let's
  188. 10:22try running it. This is the compressor.
  189. 10:25Let's see if it runs or not. Yes, the
  190. 10:28power LED is on, and now the indoor
  191. 10:31motor will run. Then the outdoor motor,
  192. 10:33then the compressor; it should run in
  193. 10:35this sequence. You can see here that
  194. 10:38the indoor motor has started. Friends,
  195. 10:41the outdoor motor takes a little time
  196. 10:44to start. So let's wait a little while.
  197. 10:48We will wait while having some tea. Yes
  198. 10:53, you can see that the motor has
  199. 10:54started. Friends, you can see the
  200. 11:04compressor has started, and as you saw,
  201. 11:07it starts very smoothly. In General,
  202. 11:11the compressor does not jerk, which is
  203. 11:14why it starts with low power. And you
  204. 11:18can see that the motor has stopped now
  205. 11:20and it will run again at high speed.
  206. 11:37You can see it has started; the indoor
  207. 11:40motor and the outdoor motor are running
  208. 11:43, and the compressor is running here
  209. 11:46too. And you can hear it gaining speed;
  210. 11:53it has reached quite a high speed. So
  211. 12:01it is running correctly, friends. Now
  212. 12:03let's turn it off. So you saw how small
  213. 12:06the ULA 2003 fault was in this. So
  214. 12:09friends, I hope you liked the video.
  215. 12:12That is all for today's video, friends.
  216. 12:14Jai Hind.

About this transcript

This page contains the full transcript of O"G, Inverter PCB Repairing communication error by Electric Locha, generated from the public captions YouTube serves with the video. The transcript has 1,576 words across 216 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.