YouTube2Text

Metallography Part II - Microscopic Techniques — Transcript

by MaterialsScience2000 · 1,510 words · 256 segments · language en · Watch on YouTube

Full transcript

  1. 0:00[Music]
  2. 0:03metallography part two microscopic
  3. 0:07techniques metallic materials are widely
  4. 0:10used in many areas of everyday life how
  5. 0:14are they built up internally are there
  6. 0:16perhaps crystals to be found and if so
  7. 0:20how big are they what kinds of crystals
  8. 0:22are there what is their shape and are
  9. 0:25there voids or inclusions metallography
  10. 0:28gives an answer
  11. 0:30in this video we would like to introduce
  12. 0:32the microscopic techniques of
  13. 0:35metallography microscopic means to
  14. 0:37investigate a workpiece at higher
  15. 0:39magnification usually with a light
  16. 0:41microscope to have a look at the inside
  17. 0:44the material has to be prepared properly
  18. 0:47and this is how it is done first of all
  19. 0:50a small specimen has to be cut from the
  20. 0:52actual
  21. 0:53workpiece the specimen is mounted in
  22. 0:56resin ground in several stages polish in
  23. 1:00several stages and finally
  24. 1:04edged now the specimen is completely
  25. 1:06prepared and ready for
  26. 1:09microscopy as a typical example we are
  27. 1:12going to investigate a bar made from a
  28. 1:14steel used millions of times the plain
  29. 1:17carbon steel
  30. 1:19c45 with
  31. 1:210.45% of carbon to start with one of our
  32. 1:25material testers defines the intended
  33. 1:27sectional plane and marks it on the the
  34. 1:30bar in this case it's a longitudinal
  35. 1:32section then he takes the bar to the
  36. 1:35abrasive saw to cut out a small sample
  37. 1:38he fixes the bar securely prepares the
  38. 1:41machine selects The Cutting parameters
  39. 1:44and starts the first abrasive
  40. 1:50cut intensive water cooling and the
  41. 1:53propriate cutting parameters are
  42. 1:55important to keep the material as cool
  43. 1:57as possible
  44. 2:01after finishing all abrasive cuts the
  45. 2:03material tester picks up the sample and
  46. 2:06hands it over to his colleague for
  47. 2:08further processing the specimen has to
  48. 2:10be mounted in resin to ensure that the
  49. 2:13resin will adhere well to the specimen
  50. 2:15surface the specimen is placed in an
  51. 2:17ultrasonic cleaner bath for a few
  52. 2:20seconds alcohol and ultrasonic waves
  53. 2:23help to remove fat and loose particles
  54. 2:25from the
  55. 2:28surface a short time under the hair
  56. 2:31dryer and the specimen is clean and
  57. 2:34dry to mount the specimen small plastic
  58. 2:37molds are suitable the material tester
  59. 2:40picks up the clean specimen and
  60. 2:41carefully places it into one of the
  61. 2:43molds the intended plane of examination
  62. 2:46is at the bottom then he pours liquid
  63. 2:49resin into the mold a thin layer of
  64. 2:51grease at the inner surface of the mold
  65. 2:53acts as a release agent this ensures
  66. 2:56that the cured resin can later be
  67. 2:58released easily from the mold
  68. 3:02now the mold containing the specimen
  69. 3:04goes into the light curing
  70. 3:07unit under the action of intense blue
  71. 3:09light the resin polymerizes within half
  72. 3:11an
  73. 3:13hour the resin has cured and embedded
  74. 3:16the specimen well as an alternative to
  75. 3:19light curing resins many other embedding
  76. 3:22materials are available each of them has
  77. 3:24its own advantages and
  78. 3:28disadvantages because the top surface is
  79. 3:30still uneven and slightly sticky the
  80. 3:33material tester grinds it there until it
  81. 3:35is even he uses a rotating water
  82. 3:38lubricated disc equipped with coar grain
  83. 3:41silicon carbide
  84. 3:43paper the circumferential surface is
  85. 3:46slightly ground as well to ensure a
  86. 3:48clean
  87. 3:50specimen now comes the most important
  88. 3:53part the preparation of the intended
  89. 3:55plane of examination our material tester
  90. 3:59begins with comparatively coarse 180
  91. 4:02grid abrasive paper he makes sure to
  92. 4:05press the specimen calmly and evenly
  93. 4:07onto the abrasive paper compensating the
  94. 4:10tendency for the SLE to tilt he also
  95. 4:13makes sure not to grind his fingertips
  96. 4:16accidentally now he has achieved an even
  97. 4:19relatively rough surface the specimen is
  98. 4:21ready for the next step with finer
  99. 4:25paper he inserts a new 320 grid abrasive
  100. 4:30paper onto the
  101. 4:32disc rotating the specimen by 90° leads
  102. 4:36to new grinding grooves perpendicular to
  103. 4:38the old ones in this way the material
  104. 4:41tester can easily check whether the old
  105. 4:43grinding grooves have been removed
  106. 4:45completely it is important to use
  107. 4:48sufficient water flushing during
  108. 4:50grinding this keeps the sample cool and
  109. 4:52prevents the abrasive paper from being
  110. 4:54loaded with material
  111. 4:56particles grinding continues with 600
  112. 4:59grit and 1,000 grit abrasive paper until
  113. 5:03an Immaculate finely ground specimen has
  114. 5:05been achieved the specimen is now ready
  115. 5:07for
  116. 5:09polishing an absolute prerequisite for
  117. 5:12polishing is a thoroughly clean specimen
  118. 5:15the ultrasonic bath and running water
  119. 5:17help to remove any residue from the
  120. 5:19ground surface otherwise hard particles
  121. 5:22might be pressed into the polishing
  122. 5:23cloth and scratch the
  123. 5:26surface hands should be washed as well
  124. 5:29so that no unwanted particles find their
  125. 5:32way to the sample and the polishing
  126. 5:34cloth now the material tester can start
  127. 5:37with a first polishing
  128. 5:39operation he chooses a polishing disc
  129. 5:42equipped with hard cloth of low
  130. 5:44resilience moistens the cloth with a
  131. 5:46suitable lubricant and adds two splashes
  132. 5:49of diamond suspension of particle size 6
  133. 5:53microm under counter rotating motion he
  134. 5:56presses the specimen with high pressure
  135. 5:58onto the polishing cloth the diamond
  136. 6:00particles have settled on the cloth and
  137. 6:02are now abrading the
  138. 6:04surface after about a minute all
  139. 6:07grinding grooves have been removed and
  140. 6:09the specimen surface already has a shiny
  141. 6:12appearance but still there are many fine
  142. 6:14scratches to be found resulting from the
  143. 6:166 microm Diamond
  144. 6:21abrasive to remove them the material
  145. 6:24tester washes the specimen and His Hands
  146. 6:26again very carefully and polishes the
  147. 6:29specimen for a second
  148. 6:30time now he uses a softer Short net
  149. 6:33polishing pad finer Diamond suspension
  150. 6:36of 3 microm particle size and less
  151. 6:43pressure after the second polishing
  152. 6:45operation the specimen surface has an
  153. 6:47almost mirror-like appearance no more
  154. 6:50scratches can be seen with a naked eye
  155. 6:53nevertheless the specimen has to be
  156. 6:54cleaned again and go through a third and
  157. 6:57final polishing operation this time 50
  158. 7:00nanom aluminium oxide abrasive is used
  159. 7:03only then is the surface prepared to a
  160. 7:05sufficient
  161. 7:07quality at the end of the mechanical
  162. 7:09preparation Special Care has to be taken
  163. 7:11to clean the specimen properly on the
  164. 7:14one hand all abrasive particles have to
  165. 7:16be removed on the other hand the freshly
  166. 7:19polished surface must not be scratched
  167. 7:22or damaged under running water the
  168. 7:24material tester gently wipes the
  169. 7:26specimen with cotton wool thoroughly
  170. 7:29rinses it with alcohol and dries it with
  171. 7:31a hair
  172. 7:33dryer from now on the sample is called a
  173. 7:36metallographic specimen or micro section
  174. 7:40judged with a naked eye our
  175. 7:41metallographic specimen seems to be well
  176. 7:44prepared it is now allowed to go under
  177. 7:46the microscope for the first time or
  178. 7:48rather onto the
  179. 7:50microscope in fact the design of typical
  180. 7:52metallographic microscopes is inverted
  181. 7:55inverted means upside down the
  182. 7:58microscope objective is not facing
  183. 8:00downwards as usual but
  184. 8:02upwards this offers the advantage of
  185. 8:05Simply placing the metallographic
  186. 8:06specimen on top of the microscope stage
  187. 8:09the prepared surface faces downwards
  188. 8:11using the built-in digital camera the
  189. 8:14polished specimen surface can be
  190. 8:15observed on the computer monitor in the
  191. 8:18polished State there isn't much to be
  192. 8:19seen in this material only some
  193. 8:22elongated non-metallic inclusions can be
  194. 8:24observed but if these inclusions are of
  195. 8:27special interest then the polished state
  196. 8:29is the perfect one inclusions May best
  197. 8:32be seen here however if one wants to see
  198. 8:35the crystals the grains and grain
  199. 8:37boundaries then the micro section has to
  200. 8:40be
  201. 8:42itched to do this our material tester
  202. 8:45protects himself with a Lap coat puts on
  203. 8:48safety glasses and pours the etchant
  204. 8:50into a small glass bowl the ENT consists
  205. 8:53of a solution of 10% of concentrated
  206. 8:56nitric acid in alcohol now now he turns
  207. 9:00on the water tab picks up the freshly
  208. 9:02polished micro section with gripping
  209. 9:04tongs and immerses it for a few seconds
  210. 9:06into the
  211. 9:08etchant then he rinses the micro section
  212. 9:11thoroughly with
  213. 9:15water and afterwards with
  214. 9:18alcohol the hair dryer is again used for
  215. 9:25drying the excitement increases was the
  216. 9:28etching time correct has everything
  217. 9:30worked out
  218. 9:35fine at low magnification not much can
  219. 9:38be seen which looks characteristic the
  220. 9:41tester gradually switches over to higher
  221. 9:44magnification in between he focuses and
  222. 9:47adjusts the brightness at medium
  223. 9:49magnification light and dark areas
  224. 9:52become
  225. 9:53visible at comparatively High
  226. 9:55magnification in some of the dark areas
  227. 9:58fine stripes may be recognized the micro
  228. 10:01structure in the darker strip regions is
  229. 10:03termed perlite perlite consists of thin
  230. 10:07alternating crystals of ferite and
  231. 10:10cementite the white regions are ferite
  232. 10:12crystals they consist of almost pure
  233. 10:15iron great the etching has been
  234. 10:19successful in a similar manner virtually
  235. 10:21all materials of our world may be
  236. 10:24examined this is the plain carbon steel
  237. 10:26c80 with 0.8% % of carbon only perlitic
  238. 10:31regions with their characteristic
  239. 10:33alternating layers of ferite and semanti
  240. 10:36can be seen and this is the plain carbon
  241. 10:39steel
  242. 10:40s235 after a color
  243. 10:43etching it only has a low carbon content
  244. 10:47the relative amount of differently
  245. 10:48colored ferite crystals is high the
  246. 10:51proportion of perlite regions low the
  247. 10:54variety of materials is huge and each
  248. 10:57material needs its own individual
  249. 10:59preparation method in metallography the
  250. 11:02preparation is often not conducted by
  251. 11:04hand as shown here but by automatic
  252. 11:07methods this saves time and
  253. 11:10money the principle however is always
  254. 11:13the same sectioning mounting grinding
  255. 11:18polishing and etching
  256. 11:22[Music]

About this transcript

This page contains the full transcript of Metallography Part II - Microscopic Techniques by MaterialsScience2000, generated from the public captions YouTube serves with the video. The transcript has 1,510 words across 256 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.