YouTube2Text

Making And using A Drawdown Bar - Meyer Rod — Transcript

by Robert Murray-Smith · 1,596 words · 213 segments · language en · Watch on YouTube

Full transcript

  1. 0:02[Music]
  2. 0:15so I'm asked quite often about coating
  3. 0:17things because obviously when you laying
  4. 0:19down a coat and you want repeatability
  5. 0:21what you need is some method of making
  6. 0:24sure that the film is the same thickness
  7. 0:26every time that you put it on now I love
  8. 0:28the times we just want to do things
  9. 0:30quickly because we want a sense of stuff
  10. 0:32in which case things like spray gunning
  11. 0:34it painting it on with the brush using a
  12. 0:38roller that sort of stuff
  13. 0:40it's fine I mean it coats pretty uneven
  14. 0:42for sure and you can be pretty much
  15. 0:44guaranteed that from one piece to the
  16. 0:46next piece the curt is not going to be
  17. 0:48the same but when you're just testing
  18. 0:50ideas and you're working through things
  19. 0:52and you're doing one or two bits of
  20. 0:54something it really is a fine method
  21. 0:56when you get closer to what it is that
  22. 0:59you want to do what you want is some
  23. 1:00kind of repeatability some way of making
  24. 1:03sure that that code is the same
  25. 1:04thickness every time you apply it now
  26. 1:07there are methodologies of doing this
  27. 1:09you've got the doctor blade but perhaps
  28. 1:12the most well used certainly in print
  29. 1:15and very often in photography for things
  30. 1:18like albumin coating or gelatin coating
  31. 1:20that kind of thing is to use what's
  32. 1:22called the draw down bar now the most
  33. 1:25popular draw down bar is this which is a
  34. 1:27Maher rot now the mayor rod is really a
  35. 1:30stainless steel wrapped piece of steel
  36. 1:33just interested blank piece of rod and
  37. 1:35they take a wire of a specific diameter
  38. 1:37and widened that wire all the way down
  39. 1:40and what it does is create little cups
  40. 1:42that are of an even depth all the way
  41. 1:44and there are standards for this for
  42. 1:47standard wire thicknesses and standard
  43. 1:49rug diameters you get for various Maher
  44. 1:51bars now the principle really is shown
  45. 1:54in this image
  46. 2:04and that's pretty much all there is to
  47. 2:06it so what we're going to do is we're
  48. 2:09going to show you how to make a mayor
  49. 2:10rod and then use that mayor rod that
  50. 2:12we've made to do some drawdown now if
  51. 2:15you don't feel like making a mayor rod
  52. 2:17then you can just use some of this stuff
  53. 2:20this is a threaded bar now it has little
  54. 2:24rounds in it and obviously it's got a
  55. 2:26helix so it will lift and create little
  56. 2:29spots but it does do a good enough job
  57. 2:31if you don't feel like using a mayor rod
  58. 2:34and you can get this in different
  59. 2:35diameters so I think this is an m8 this
  60. 2:39one's an m12 and you can see I've used
  61. 2:41this quite often actually and then make
  62. 2:44pretty decent drawdown bars as well
  63. 2:46perhaps not the best but certainly
  64. 2:48pretty decent the mayor rods like I said
  65. 2:51just a normal bit of Steel this is just
  66. 2:53mild steel wraps with some stainless
  67. 2:56steel wire this is a bit of stainless
  68. 2:58steel rod incidentally which lasts a
  69. 2:59little bit longer and you make that now
  70. 3:02the work to make this is like this so to
  71. 3:06make a mayor rod actually is really easy
  72. 3:07what I've got here is a bit of bar it's
  73. 3:09one centimeter mild steel and all I need
  74. 3:12to do is drill a hole in either end I've
  75. 3:14put a flat spot on the bar incidentally
  76. 3:16it just makes it drilling it that much
  77. 3:18easier the drill doesn't skip off the
  78. 3:20round surface so put that into a vise
  79. 3:23and into the drill we can do a couple of
  80. 3:25holes
  81. 3:31[Music]
  82. 3:42holes drilled in it what I've got here
  83. 3:45is a bit of stainless steel now the only
  84. 3:47reason I'm using 1 centimeter bar and
  85. 3:49mr. cendars steel which is point eight 1
  86. 3:51millimeters incidentally is because it's
  87. 3:54what I have lying around to be honest
  88. 3:57you can you so you should use different
  89. 3:59gauges of stainless steel because the
  90. 4:02different gauges of the stainless steel
  91. 4:03will give you different thicknesses of
  92. 4:05film and we'll go through that when
  93. 4:07we're actually sat on the desk but to
  94. 4:08show you how to make the bar are the rod
  95. 4:11you just feed the stainless steel in a
  96. 4:13couple of times through the hole that
  97. 4:14you've just done and pull it tight and
  98. 4:16that'll be enough to actually make a
  99. 4:18kind of knot in the end of the steel
  100. 4:24okay and then twist that round a couple
  101. 4:27of times and then clip it off obviously
  102. 4:36I've got a Ledge here and what we're
  103. 4:39gonna do is wind a coil on the lathe so
  104. 4:41the bomb goes into the lathe and you're
  105. 4:46gonna progress it gave me a bit too far
  106. 4:48out obviously the bar will Bend as you
  107. 4:50pull on the wire because you have to
  108. 4:51give it a fair pull to get that thing to
  109. 4:54work I'll just remove the stock
  110. 5:06and if I can remember which way around
  111. 5:08this lid goes so it's turning in that
  112. 5:20direction pull your wire tight give it a
  113. 5:28couple of turns by hand just to get it
  114. 5:31going
  115. 5:51and when you get close up to this turn
  116. 5:54it off
  117. 5:54move it up feed it in and that's all you
  118. 5:56do so you've gone right to the end your
  119. 5:58hole is right there incidentally put
  120. 6:00your thumb on it snip off a fair length
  121. 6:07and then you want to feed it through the
  122. 6:09hole at the other end
  123. 6:40once you've done that Tetsu may rod made
  124. 6:44incidentally you wind and kiln coils in
  125. 6:47a similar way to this just get yourself
  126. 6:48a bar want the coil pull it off stretch
  127. 6:51it out and it's exactly the same method
  128. 6:52for winding a kiln coil is for making a
  129. 6:55mayor rod but there's the mayor rod now
  130. 6:57let's get back to the desk and use it so
  131. 6:59once you've made you mayor rod you now
  132. 7:01have actually a very precise instrument
  133. 7:03for being able to do film thicknesses
  134. 7:05but are very very repeatable time and
  135. 7:08time again those little hills that are
  136. 7:11formed sink down a little bit and the
  137. 7:13final finished coat thickness is related
  138. 7:16to the solid contents of your ink so if
  139. 7:19you draw down a hundred micrometer thick
  140. 7:21film and get a 40 percent of solids
  141. 7:24content what you're going to end up with
  142. 7:26is a 40 micrometer thick film time after
  143. 7:30time after time so as long as you know
  144. 7:32the solid content of your ink the damage
  145. 7:35of the wire if you bar then your film
  146. 7:37can be calculated really easily and will
  147. 7:40be consistent of the entire substrate
  148. 7:42now obviously when you're laying down
  149. 7:44the substrate what you need is a flat
  150. 7:46hard surface and here's a bit of
  151. 7:48tempered glass that wasn't too expensive
  152. 7:50actually it was a shelf it's it's a
  153. 7:52shelf from a cupboard that I got from
  154. 7:54little local DIY store and get a bit of
  155. 7:57your substrate
  156. 7:58just attach it to your shelf or your
  157. 8:03hard flat surface now I'm going to be
  158. 8:06using our ink incidentally so I'm gonna
  159. 8:09put a bit of gloves on just to stop my
  160. 8:10hands getting too dirty
  161. 8:24I've hidden the ink another stir just
  162. 8:27before I use it to make sure we've got
  163. 8:28good even distribution lay your May
  164. 8:31around in handy and we'll get a bit of
  165. 8:35ink ready to go on that
  166. 8:47put your into cross
  167. 8:52and then pull the bar down don't roll it
  168. 9:00and then leave it to dry and you get a
  169. 9:02beautiful coat on that every time okay
  170. 9:06so just to run through that one more
  171. 9:07time a nice flat surface but a tempered
  172. 9:10glass works really well hard and flat
  173. 9:12get your substrate whatever that happens
  174. 9:14to be I'm using this stuff obviously
  175. 9:16twitch is head to dpe attach that to
  176. 9:20your flat surface you might use a
  177. 9:22different material it's totally up to
  178. 9:24you but I'm using that put the gloves on
  179. 9:28so I don't get to inky because I'm
  180. 9:30always washing my hands you may a rod
  181. 9:37nice and ready
  182. 9:38remember the thickness of the film is
  183. 9:40related to the wire diameter is half the
  184. 9:42wire diameter and then the solid content
  185. 9:45and you can change that thickness by
  186. 9:47changing the wire diameter so clearly a
  187. 9:49larger diameter wire is gonna give you a
  188. 9:51thicker film a thinner diameter wire
  189. 9:53will give you a thinner film so changing
  190. 9:55that wire diameter changes the film
  191. 9:57thickness but the key of it is its
  192. 9:59repeatable again and again and again so
  193. 10:02we've got some ink in our syringe we put
  194. 10:04a bit of income the substrate
  195. 10:10don't roll the bar draw the bar so there
  196. 10:16we go a beautiful coat and here's the
  197. 10:19one that we did earlier as you can see
  198. 10:22it's nice and shiny and then we'll leave
  199. 10:24that to dry properly and that's finished
  200. 10:26so very easy to do now I did look at the
  201. 10:30price of these things and they're about
  202. 10:32two hundred and fifty dollars to buy
  203. 10:34which I thought was crazy so that's how
  204. 10:36you go about making one we might
  205. 10:38actually start making these and selling
  206. 10:40them on the shop we haven't decided on
  207. 10:41that or not I guess it depends how much
  208. 10:43call there is for it really and how much
  209. 10:44time we have but they're really easy to
  210. 10:46make at home yourself and they do a
  211. 10:48beautiful beautiful job so I hope that
  212. 10:50was of interest to you
  213. 10:52and thank you very much for watching

About this transcript

This page contains the full transcript of Making And using A Drawdown Bar - Meyer Rod by Robert Murray-Smith, generated from the public captions YouTube serves with the video. The transcript has 1,596 words across 213 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.