YouTube2Text

Juke 1.5dCi DPF Pressure Sensor Fault P1453 / Limp Mode / Blocked DPF — Transcript

by Stupid Bloke Stupid Videos · 2,461 words · 363 segments · language en · Watch on YouTube

Full transcript

  1. 0:00cuz if you don't succeed. [music]
  2. 0:04>> Hi, welcome back to the channel. So, we
  3. 0:06are in the Nissan Juke and recently, not
  4. 0:10that long ago, in fact, like two days
  5. 0:12ago, we replaced the math sensor and it
  6. 0:15fixed a load of problems. Got rid of the
  7. 0:16engine light, all the cruise control and
  8. 0:18everything was working. I had full power
  9. 0:21and like I say, it's lasted like 2 days
  10. 0:23and then now the engine light is back
  11. 0:25on. As you can see, all that [ __ ]
  12. 0:28stopped working again. and power it's
  13. 0:30before I did the math sensor I was
  14. 0:31getting it like up to full power then it
  15. 0:32would backing off and then it would come
  16. 0:33back. Now it just goes halfway and
  17. 0:35that's all I get is in limp bit more
  18. 0:36proper. So let's try and see what's
  19. 0:39wrong with it. I have got this plugged
  20. 0:41in and we can see the faults that we
  21. 0:44have. We've got all the same faults as
  22. 0:47we had before apart from not the one for
  23. 0:49the math sensor.
  24. 0:51Um, and that's the one that's the one
  25. 0:54there
  26. 0:56that I'm going to focus on cuz I think
  27. 0:57that's where the issue is.
  28. 1:00So, let's have a look at that. And if we
  29. 1:03open the bonnet
  30. 1:06and go around to this location,
  31. 1:09we have got a sensor there.
  32. 1:12And that sensor is there to measure the
  33. 1:15exhaust pressure behind the DPF to work
  34. 1:17out
  35. 1:18the particle filter differential
  36. 1:20pressure which
  37. 1:25as you can see from that
  38. 1:28staying at that it is not doing [music]
  39. 1:32it
  40. 1:36>> and it could be not doing that for a few
  41. 1:38reasons. It could be because this sensor
  42. 1:41is fault. It could be the wiring to the
  43. 1:43sensor that is the issue. But what is
  44. 1:47most likely I've had issues before in a
  45. 1:49couple of videos actually is this pipe
  46. 1:52being completely blocked and not letting
  47. 1:55the exhaust out of it. So that's what I
  48. 1:56suspect it is. So to check that I need
  49. 2:00to remove this
  50. 2:02by carefully pulling this clip out
  51. 2:06like so.
  52. 2:08And then this
  53. 2:10will just about not fit out obviously.
  54. 2:13But with a bit of
  55. 2:16gentle persuasion,
  56. 2:18it will do. And now I need to remove
  57. 2:21that pipe from it, which is just a case
  58. 2:23of taking the pliers, squashing them,
  59. 2:26and then pulling this out as I do that.
  60. 2:31Yes.
  61. 2:33So now if we start the vehicle we should
  62. 2:34have exhaust gases coming out of here
  63. 2:38which
  64. 2:41surprisingly
  65. 2:44we actually do have.
  66. 2:47So it's looking like I might just have
  67. 2:49to change that sensor which more
  68. 2:51expensive but an easier fix than
  69. 2:54unlocking the pipe.
  70. 2:56And now we have got a new sensor from
  71. 3:00MAS. And if we take out the box and put
  72. 3:03it next to the old one, then we can see
  73. 3:06that hopefully it looks like at least
  74. 3:08that it is the correct one. Yes. So
  75. 3:13after confirming that it does appear to
  76. 3:15be the correct one, I can just carefully
  77. 3:18fit it.
  78. 3:22Something like that. Not forgetting to
  79. 3:25refit this clip to hold it in place.
  80. 3:31and obviously this clip
  81. 3:34to make sure it's sealed.
  82. 3:38And then
  83. 3:40once we plug it in the right way around,
  84. 3:45hopefully that will now give us a
  85. 3:46reading.
  86. 3:48And so we'll plug back into it, start it
  87. 3:51up, and see what it reads. Now, I have
  88. 3:53already reset the fault codes. It might
  89. 3:56not read anything unless you reset the
  90. 3:58fault codes first. But we have got a
  91. 4:02reading. So, let's start it up.
  92. 4:07Yes.
  93. 4:21So now that we have a reading hopefully
  94. 4:23it will be able to measure the DPF uh
  95. 4:26back pressure and regen as required and
  96. 4:30give me full power and keep the full
  97. 4:31power rather than give me limp dip mode.
  98. 4:34So I will go and see if it behaves
  99. 4:37itself
  100. 4:41power
  101. 4:43and if it doesn't and decides that the
  102. 4:45DPF is too blocked then I I mean I don't
  103. 4:48think it is but if it decides that it is
  104. 4:50then
  105. 4:52we can always do a regen using this
  106. 4:54scanner which I will put a link in the
  107. 4:57description for and a discount code and
  108. 4:58all that [ __ ] Um I've shown it in other
  109. 5:00videos. It's not expensive and it has
  110. 5:05quite a few functions on it. So, it's
  111. 5:07pretty good actually. Uh but anyway,
  112. 5:09let's go and see if it gives us the
  113. 5:12power.
  114. 5:14Yes. And so, it behaved itself for a bit
  115. 5:17until I put my foot down and now it's
  116. 5:19come up with a code, a different DPF
  117. 5:21code, but from what I can tell it's in
  118. 5:23the DPF is is blocked. So,
  119. 5:27let's see if I can do
  120. 5:30a regen.
  121. 5:37Yes.
  122. 5:42And it did that for a few minutes. And
  123. 5:44it seems that now
  124. 5:47we're up to temperature. The revs have
  125. 5:50decreased to about 2K.
  126. 5:54And it does smell
  127. 5:57like it's doing a regen.
  128. 6:06And that seems like that might
  129. 6:09be that done.
  130. 6:14So it seems that we have completed a
  131. 6:16regen. But it also seems
  132. 6:20that I have made a mistake
  133. 6:22because I didn't realize that there is
  134. 6:24another exhaust pressure sensor. And it
  135. 6:27should have been obvious when I got this
  136. 6:29one working and changed that and then I
  137. 6:31got a reading on that and then I got a
  138. 6:34negative reading. It should have pointed
  139. 6:36me in the right direction. I was
  140. 6:38checking this for a split in it. doing a
  141. 6:42little bit of research and talking to a
  142. 6:43mate of mine who knows a bit more than
  143. 6:45me about these [ __ ] cars.
  144. 6:48There is in fact another pressure sensor
  145. 6:50and it is in such a fun place. Let me
  146. 6:52show you. We zoom in on this bit here.
  147. 6:56Look down there
  148. 6:58around that area.
  149. 7:02Well, in that area precisely in that
  150. 7:05area
  151. 7:06there is in fact another DPF pressure
  152. 7:09sensor. And if I stick the phone down
  153. 7:10the back of there,
  154. 7:14and if you look really carefully, you
  155. 7:16might have noticed that it appears that
  156. 7:18one of them pipes is split. And that
  157. 7:20would explain the negative reading.
  158. 7:22And so we need to replace that pipe. And
  159. 7:26obviously,
  160. 7:28it's in a location that doesn't give
  161. 7:31easy access.
  162. 7:33So, can I do it by just taking this
  163. 7:37airbox out and taking this pipe off and
  164. 7:40then reaching down the back? Or do I
  165. 7:43need to do what you're supposed to do
  166. 7:46and take all this off,
  167. 7:49which I'm not sure if I can be [ __ ]
  168. 7:50with. And so, what I'm going to do is
  169. 7:53I'm going to take all this off, the
  170. 7:55intake off, the airbox off, and that
  171. 7:57pipe off, which isn't too hard to do. I
  172. 7:59mean, I've shown it in other videos, but
  173. 8:00there's like an 8 mil down there on a
  174. 8:02Jubilee clip. There's one there. There's
  175. 8:03a 10 mill there. The rest sort of just
  176. 8:05pulls out, unplug it and what have you.
  177. 8:08That'll be out the way. And then when I
  178. 8:10still inevitably can't get to the plug
  179. 8:12or to the pipe that I need to change,
  180. 8:14then I'll take all this [ __ ] off.
  181. 8:18Yes. And so that does give us a bit more
  182. 8:22room. And
  183. 8:25I can even touch the pipe. That's the
  184. 8:28issue. But as anticipated, I've still
  185. 8:32not got enough room. So, I'm going have
  186. 8:33to take all that off. So, I suppose I'll
  187. 8:36start
  188. 8:38by taking the wipers off, which is a 14
  189. 8:41mm.
  190. 8:43[snorts]
  191. 8:47And with that removed,
  192. 8:50we should be able to wiggle as long as
  193. 8:52it's not seized on, which sometimes the
  194. 8:55wipers do, but that one wasn't.
  195. 8:59Unfortunately, neither was that one. So,
  196. 9:01now let's carefully remove this, which
  197. 9:03is on those things. That should say I
  198. 9:06should should just pull off as long as
  199. 9:09you're careful about it.
  200. 9:12Yes, something like that. And be careful
  201. 9:16not to let these fall out because that
  202. 9:19one flicked out and there's now it's
  203. 9:21like down there somewhere
  204. 9:24where it could probably end up staying.
  205. 9:26Um, so now this is pretty good. So this
  206. 9:28is off there, but then we've got
  207. 9:34some of the little clips
  208. 9:38which we need to pull out. And then we
  209. 9:41can remove that.
  210. 9:43And then
  211. 9:45we can remove this pipe
  212. 9:48by just releasing these clips
  213. 9:52like so.
  214. 9:55And then it just pulls out of that one.
  215. 10:02That's perfectly demonstrated there. Um,
  216. 10:05probably didn't need to remove that and
  217. 10:06all this [ __ ] because there's a little
  218. 10:08gap where I could probably just get to
  219. 10:09this
  220. 10:11without taking that off. But we are
  221. 10:13here. Um, I need to take all these out.
  222. 10:15There's There's one there. There's one
  223. 10:18there. There's They're all across the
  224. 10:19front of there. And then with those
  225. 10:21removed,
  226. 10:24this feels like there's not that much
  227. 10:26holding it in. Um,
  228. 10:30that might be a problem. That might need
  229. 10:31taken out.
  230. 10:37Yes. And so I'm hoping with both sides
  231. 10:40disconnected, I'm going to be able to
  232. 10:42lift this up
  233. 10:49and slide it.
  234. 10:51Something like that. The washers,
  235. 10:54they're probably still connected.
  236. 10:59And so that leaves us with this. And
  237. 11:01they take the wiping water out, which is
  238. 11:03just wonderful. We unplug it from here
  239. 11:07somehow. And then there's a 10 m bolts,
  240. 11:10like four of them. And then once that's
  241. 11:12out the way, I'll come back.
  242. 11:18And now with that out the way, there
  243. 11:20isn't that much stopping us from getting
  244. 11:22to it. There's a plate here which has
  245. 11:24got various 10 mmas
  246. 11:27holding it in. It's also got a wiring
  247. 11:30loom attached to it there. But that
  248. 11:31might be easy to take off once I've
  249. 11:33removed them, which I've now done. So
  250. 11:38maybe in fact, to be honest with you,
  251. 11:41that gives me the access that require.
  252. 11:43It's still not that easy to reach. But
  253. 11:45if we go down here then we should be
  254. 11:46able to see the issue which is
  255. 11:50that there
  256. 11:53pipe
  257. 11:55which I'm pretty sure has a nasty split
  258. 11:58in it. So I need to change that and it
  259. 12:01is a bit of a [ __ ] to get to and
  260. 12:04you're not going to be able to see it
  261. 12:05unfortunately. So I'm just going to do
  262. 12:07that off camera I think.
  263. 12:10Yes. And that was loads of fun to get
  264. 12:13to. Um, we can see where the issue is. I
  265. 12:17thought it was split along it, but
  266. 12:18that's just a seam in the pipe. It's
  267. 12:19actually split that way. And that
  268. 12:23explains why we had a minus reading. Uh,
  269. 12:26because the split is on the pre- DPF
  270. 12:29side. So, that was reading lower than
  271. 12:32after the DPF because of the split. And
  272. 12:34it should have been obvious. I mean, I
  273. 12:37sort of scratched my head why it was
  274. 12:39doing a minus. And that usually means a
  275. 12:40split pipe. I mean, like I said, it's
  276. 12:42think about it logically that's obvious.
  277. 12:44But anyway, to take that off, that was,
  278. 12:47like I said, loads of fun. We have got
  279. 12:49our sensor, which the way that I did it
  280. 12:51was is I took the sensor off and pulled
  281. 12:53it out the pipe work
  282. 12:55and then fought with the pipe work
  283. 12:57afterwards. One of them things, you
  284. 12:59know, it's it's pretty awkward to get
  285. 13:01to. It reminded me of doing the
  286. 13:02thermostat on the uh on the golf where I
  287. 13:04sort of questioned why the [ __ ] I do
  288. 13:07this, you You know what I mean? You
  289. 13:09might not believe this, but I was
  290. 13:10actually smart at school. I mean, I was
  291. 13:11a dick, but I was smart at school. I
  292. 13:14could have had a proper job what I'm
  293. 13:15doing. Anyway, now I need to replace
  294. 13:18that pipe with one that's not fooked.
  295. 13:21And here is the replacement pipe. Now,
  296. 13:23this is fun. So, one end of it is like 6
  297. 13:27mill where it goes onto the pipe off the
  298. 13:29DPF. And then when it goes into that
  299. 13:30sensor there, that that's like 8 mill.
  300. 13:33So, I've got a piece of high-pressure
  301. 13:36fuel hose, which is supposed to be quite
  302. 13:38good for heat resistance. And what I've
  303. 13:40done with it is I've just put like a 8
  304. 13:42mil drill bit down one end of it to make
  305. 13:46one end of it 8 mil. So, I'm going to
  306. 13:48fit that. Hopefully, it survives, does
  307. 13:52the job. I don't want to do this again.
  308. 13:54But, yeah, I'm going to put that back
  309. 13:56on, which is a reversal of taking it
  310. 13:58off, which I didn't show that either.
  311. 14:00I'm not going to show this bit because
  312. 14:02it's just not really easy to show.
  313. 14:06Yes.
  314. 14:08So there, that is the new pipe fitted.
  315. 14:10And now I just need to put all this back
  316. 14:12together, which is a reversal of taking
  317. 14:14it apart.
  318. 14:16So unless there's something interesting
  319. 14:17along the way, I'll come back when that
  320. 14:20is done.
  321. 14:22Like so. And there was in fact nothing
  322. 14:24interesting. Uh just make sure you line
  323. 14:27all that up. Line your wipers up to
  324. 14:29where they were on the windscreen. Use
  325. 14:30the marks off the windscreen to put them
  326. 14:32back in the same place and what have
  327. 14:33you. And then it should be nice and
  328. 14:35simple.
  329. 14:38And now, of course, we need to
  330. 14:42clear the fault codes. Obviously, we
  331. 14:45still got that one for the eater plugs
  332. 14:47or the control module, whatever it is.
  333. 14:48That'll be another video and hopefully
  334. 14:49it won't cause it to go into lint dick
  335. 14:52mode. But let's go and see if it works.
  336. 15:01Yes.
  337. 15:09Yeah. It does appear that we're in fact
  338. 15:12getting all of the uh 109 brake
  339. 15:16horsepowers that are on offer. And um
  340. 15:20it's not [ __ ] up yet. So, I did the
  341. 15:23math sensor recently and then it were
  342. 15:25all right for a couple of days and I
  343. 15:26thought, "Oh, yeah, great. It's it's
  344. 15:28working as it should do and then the
  345. 15:31light come back on and then if I reset
  346. 15:34it, it had come back on instantly." So,
  347. 15:36what I actually think happened was is
  348. 15:38you seen that pipe earlier on in the
  349. 15:40video which was split. I think when I
  350. 15:44changed the math sensor, it give it just
  351. 15:46so much power that it wasn't used to
  352. 15:48having and um then that that might have
  353. 15:51split that pipe
  354. 15:54maybe.
  355. 15:56So anyway, now hopefully that is the end
  356. 16:02of it and um it should work as well as
  357. 16:07designed, but we'll see. I'll put it in
  358. 16:09the uh the comments or in the
  359. 16:11description if it screws up again. But
  360. 16:13so far so good. So, I think I'm going to
  361. 16:16leave it there. Don't forget to like,
  362. 16:18comment, subscribe, all your [ __ ] And
  363. 16:20I'll see you next time.

About this transcript

This page contains the full transcript of Juke 1.5dCi DPF Pressure Sensor Fault P1453 / Limp Mode / Blocked DPF by Stupid Bloke Stupid Videos, generated from the public captions YouTube serves with the video. The transcript has 2,461 words across 363 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.