IS THIS $300 ESPRESSO TOOL WORTH IT?: The Porcupress Review — Transcript
Full transcript
- 0:00what's up everyone lance hedrick here
- 0:02and today we're going to look at
- 0:05the porcupress
- 0:07[Music]
- 0:14now to begin i would ask that you all
- 0:16take a second you know like subscribe if
- 0:18you haven't yet that'll be awesome um
- 0:20yeah and then check out i'm going to put
- 0:22down below um who this is works design
- 0:25sheldon did send this to me for free so
- 0:27i want to be upfront about that but what
- 0:28i'm doing in this video is is somewhat
- 0:30it's pretty objective so um it's not
- 0:32really going to be affecting what i'm
- 0:34saying i'm doing a more so of an
- 0:36objective analysis of what this does i
- 0:37will talk about taste at the end but
- 0:39you'll see when we get there okay
- 0:42so you're looking at this and you're
- 0:43saying what the heck is this i have no
- 0:46idea i'm gonna read what sheldon himself
- 0:49says about this tool um but anyway the
- 0:52porky press is here to help reduce
- 0:54channeling specifically on very finely
- 0:56ground coffee the tool perforates the
- 0:58coffee puck such that after you tamp you
- 1:01will leave behind a defined array of
- 1:03less compacted regions these regions
- 1:06will initially allow water through the
- 1:08entire depth of the puck water will then
- 1:10saturate outwards from each of these
- 1:12holes causing the entire puck of coffee
- 1:14to be fully wet as the entire puck
- 1:16swells these holes in other naturally
- 1:18present channels will seal up so the
- 1:20idea according to sheldon is you have
- 1:22your untamped bed of coffee
- 1:27you have your untamed bed of coffee you
- 1:29wdt do whatever do whatever preparation
- 1:32preparation you need to do and then
- 1:34you're going to take this and as you see
- 1:35we have little
- 1:37flaps for the flaps on your portafilter
- 1:39you're gonna put it on and then watch
- 1:41see this you're gonna go down and you're
- 1:43gonna perforate the coffee with all
- 1:45those needles okay so what's gonna
- 1:47happen is you're gonna have holes you're
- 1:48gonna have a holy puck so there's gonna
- 1:50be holes all over the place all right
- 1:52then you're gonna tamp on top of that
- 1:53and the speculation what sheldon says is
- 1:55that's going to cause a less dense puck
- 1:57because you're going to have all these
- 1:58different little holes in it though
- 1:59they're still going to be there even
- 2:01though you won't see them and so when
- 2:02the water hits it the water is going to
- 2:04find these lesser dense areas that its
- 2:06water is going to be able to get to the
- 2:07bottom of the puck with less perturbance
- 2:09and it's going to be able to give you a
- 2:11more even extraction okay and it's going
- 2:13to seal up those channels when the
- 2:14coffee expands okay so that is kind of
- 2:17the philosophy behind it so the
- 2:18origination of this idea doesn't
- 2:19actually trace back to sheldon it
- 2:21predates sheldon it goes back to 2016 or
- 2:23so when matt perger uh down at barista
- 2:26hustle was playing with this idea with
- 2:27his with michael cameron so they had
- 2:29this idea they had tools you can
- 2:32actually see a video i'll link below
- 2:33where they discuss this in 2017 uh this
- 2:36idea that they've been having and
- 2:37sitting on for the past year when they
- 2:38made that video so this is a
- 2:40pre-established idea and this is just an
- 2:43engineered version of what they were
- 2:45talking about and
- 2:47very well engineered i might add so is
- 2:50that actually what's going on though
- 2:51because i know you're watching this and
- 2:52you're going
- 2:53there's no way right so
- 2:56you know what we can test it out i know
- 2:58that there have been other videos made
- 2:59on this there have been other people who
- 3:01have done tests with it and it shows a
- 3:03minimal increase in extraction and so i
- 3:05was wanting to find someone to
- 3:06collaborate with on compiling some data
- 3:10and so i found out a friend of mine from
- 3:12the espresso aficionado discord had
- 3:14already begun doing a study on this and
- 3:16was about to publish a blog so i talked
- 3:18with him i corroborated some of his
- 3:20evidence and i'm going to present to you
- 3:21now what shay
- 3:23has found about what actually happens
- 3:27when you use this and it is not what you
- 3:29think it is
- 3:32so
- 3:33what this actually does according to his
- 3:35study i'm just going to give you the
- 3:36tldr or too long didn't watch tldw
- 3:39what this is actually doing is it is not
- 3:42creating those channels in fact what it
- 3:43is doing is it is priming your puck to
- 3:45be able to be compressed to a higher
- 3:47density
- 3:49what what does that even mean so i have
- 3:52this blog below so you can you can look
- 3:53more in depth there but in short what's
- 3:56going on is when you create those holes
- 3:58hypothetically what's going on is you
- 4:00are creating a more
- 4:03susceptible bed for a higher compression
- 4:05when you tamp it okay so that just means
- 4:07whenever you use normal wdt and then you
- 4:10tamp you have x density and then
- 4:12whenever you use the porky press and
- 4:14then you tamp you have x density
- 4:17plus a little bit okay that's i'm not
- 4:20obviously mathematically correct but
- 4:21that the idea i'm trying to get is
- 4:23whenever you don't use the porky press
- 4:24you have a lesser dense puck than when
- 4:26you do use the porky press and this is
- 4:28all laid out in his blog the way he
- 4:30discovered this is he measured the puck
- 4:31density of with wdt and tamp and then
- 4:34wdt porky press and tamp the way he
- 4:37measured it was using a methodology
- 4:39outlined by michael cooper michael
- 4:41cameron who is with perger michael
- 4:42cooper who has an instagram called uh
- 4:45quantitative cafe i'll have a link down
- 4:47below go check out the work that
- 4:48michael's doing it's fantastic data
- 4:50analysis anyway by using the the method
- 4:54that michael cooper came up with on how
- 4:55to measure putt density shea repeated
- 4:57this experiment four times and found a
- 4:59direct correlation between using the
- 5:01porky press and the uh and not using the
- 5:04porcupine as regards the density so what
- 5:06does that mean you have higher density
- 5:08when using the porcupress this means
- 5:09that you have been able to take out dead
- 5:11space more dead space than without using
- 5:13it which can arguably increase your
- 5:16extraction now
- 5:18i ran the numbers i did exactly what
- 5:20shea did and i found that indeed when
- 5:22you're using really finely ground coffee
- 5:24you can in fact get higher extractions
- 5:27and i'll put my numbers up right here so
- 5:29what i found is when i did a a slow
- 5:32bloom style shot on the decent i
- 5:33replicated shae's parameters almost
- 5:35exactly on the decent espresso machine
- 5:37so i could have a consistent output
- 5:39when i replicated it i found a one to
- 5:41one and a half percent variance when i
- 5:44wasn't using the perky press versus when
- 5:46i was however when i first did the
- 5:48experiments i did not want to have to
- 5:50use some sort of crazy flow profile i
- 5:52used instead my breville dual boiler and
- 5:54i used just typical pre-infusion into a
- 5:57nine bar shot i did i wanted to see if
- 5:59this was
- 6:00purposeful for the typical home user who
- 6:02doesn't have you know an insane machine
- 6:04that allows you to do crazy float
- 6:05profiles and what i found was there was
- 6:07little to no difference with or without
- 6:09the porcupress when i was talking to
- 6:11shea about this it turns out that the
- 6:13coarser you go in your grind size the
- 6:15less of an effect this has and it's
- 6:17because the coarser you go the less
- 6:20channeling there's going to be in
- 6:22general because the coarser it is the
- 6:23less clumping the less um
- 6:26the less higher dense
- 6:28areas in the puck will be occurring for
- 6:30there to be a need for this porky press
- 6:32which allows for a higher density tamp
- 6:34so that actually collaborates well with
- 6:37the chris hendon paper that i discuss in
- 6:40this video on turbo shots that talks
- 6:42about this volcano effect whenever you
- 6:44you would expect when you start let's
- 6:46say we have an x y axis here so we're
- 6:48actually going to draw it with my finger
- 6:49and i'm going to do it the opposite
- 6:50direction i'm going to do it this so it
- 6:51makes more sense for you boom all right
- 6:53now down here on the x-axis we have
- 6:56fineness to coarseness on the y-axis we
- 7:00have extraction yield okay
- 7:03fineness to coarseness extraction yield
- 7:04now if you're thinking about it the more
- 7:06surface area that you expose when
- 7:08grinding finer and finer you should be
- 7:10able to go higher and higher and higher
- 7:12until you can't grind and find any more
- 7:14right
- 7:15theoretically that's what should happen
- 7:17but what was discovered in that hidden
- 7:19paper with turbo shots is that you
- 7:21actually increase increase increase
- 7:22until a certain amount and then you
- 7:24start to decrease extraction and that is
- 7:26very peculiar the reason is because as
- 7:29you get finer and finer it's more and
- 7:31more difficult for the water to go
- 7:33through the puck evenly a lot of
- 7:35channels become created and you start
- 7:37decreasing your extraction
- 7:39so
- 7:40what you can do is use this porky press
- 7:42it allows for more even extraction
- 7:44allows for the water to go through it
- 7:45more evenly by breaking up by by
- 7:48disallowing some of those clumps that
- 7:49might disallow a higher density and uh
- 7:52and forces the water through at a more
- 7:55even rate okay so instead of having the
- 7:57peak be say here on our graph maybe we
- 7:59can move the peak a little higher to
- 8:01over here you know so that's kind of
- 8:03what the purpose of this tool is is when
- 8:04you get into those really fine settings
- 8:06where it's difficult to control
- 8:07channeling this can help you by
- 8:09increasing your puck density and thereby
- 8:11increasing your extraction yield now
- 8:14let's just ask the question is this
- 8:16absolutely necessary even if it does
- 8:18increase it
- 8:20it depends on what you're looking for in
- 8:21a coffee i have found that when i do use
- 8:24this side by side with one that i don't
- 8:25use a porky press and where it does work
- 8:28effectively enough to have one or one
- 8:29and a half percent extraction advantage
- 8:32over the other i have found sweeter
- 8:34shots okay and a little more clarity a
- 8:37little less muddle and i suspect it's
- 8:38because i'm getting a little less
- 8:40channels and a little higher extraction
- 8:42with
- 8:43without with a more even extraction
- 8:45throughout the bed so maybe i'm getting
- 8:4723 percent without the porcupress and i
- 8:49have a part of the puck that's 25 apart
- 8:52that's 20
- 8:53perhaps with this i'm getting more
- 8:54evenly 24 across the pug so i'm not
- 8:56getting some undesired flavors from
- 8:58certain parts of the puck that i might
- 9:00in one without the porky press of course
- 9:01this is all speculation but what i'm
- 9:03trying to get at is i have noticed an
- 9:05increase in my enjoyment of the espresso
- 9:07using the porky press but only in those
- 9:10shots where you use a fine enough grind
- 9:12where it would make a difference if
- 9:13you're doing nine bar style shots or
- 9:15even i did a 20 second pre-infusion nine
- 9:18bar shot and even there the differences
- 9:20were so minimal it didn't really matter
- 9:22if i used the porcupress or not so
- 9:25does this tool matter
- 9:28it depends on what style of espresso
- 9:29you're drinking if you're doing darker
- 9:31roasted coffees it's not going to do
- 9:32anything for you if you're doing medium
- 9:34to light to really lightly roasted
- 9:35coffees and you're doing crazy flow
- 9:37profiles this can really increase your
- 9:39extraction and can really help with some
- 9:42skewed puck preparation but is it
- 9:44necessary that's up for you to decide
- 9:47now what i'm going to do now just as
- 9:49proof because i know you all like this
- 9:50i'm going to pull two shots
- 9:52and one of them i'm going to use a porky
- 9:54press one i'm not going to use a porky
- 9:55press i'm going to quickly measure the
- 9:56extraction and then we're going to taste
- 9:58it and i'm going to show you the how i
- 10:00did it how i did these shots when i was
- 10:03collecting data which it mirrors what
- 10:05shea was doing when collecting their
- 10:06data so here we go i'm going to get
- 10:08these shots ready here we go boom all
- 10:10right so the way i'm going to be
- 10:11preparing this is i've got these chemex
- 10:13filters that i cut using a 2.25 inch
- 10:16hole cutter
- 10:17and i have same basket in both of these
- 10:19portafilters they're both 18 grand
- 10:21baskets and so i put the filter on the
- 10:23bottom i'll grind the coffee up dump it
- 10:25in here and then i'm going to take
- 10:27just as shae did
- 10:29let's see
- 10:30i'm going to take my 0.3 millimeter wdt
- 10:34tool same exact one that shea used and
- 10:36i'm going to be doing deep wdt the way
- 10:38that i do it which is i like to call it
- 10:40earth around the sun so we're going to
- 10:41do small rotations in a big revolution
- 10:43and i'm going to do that all the way up
- 10:45to the surface then right after that i'm
- 10:47gonna give for when i do porky press a
- 10:49slight tap
- 10:51put it on
- 10:52punch
- 10:53flip it
- 10:54punch and that way i get double the
- 10:56amount of holes because the design flips
- 10:57at 180. and then the other one i'm going
- 10:59to do everything the same with the
- 11:00slight tap and all i won't use a porky
- 11:02press i'll just tamp and for the tamping
- 11:05i'll be using
- 11:06my calibrated
- 11:08self-leveling decent v3 tamper so this
- 11:12is going to allow me to replicate almost
- 11:14exactly uh the the puck preparation in
- 11:17both and then we'll pull the shots we'll
- 11:19see which one uh what what they pulled
- 11:21in the extraction level and then taste
- 11:23and then we'll be done all right and
- 11:24here we go all right so i just pulled
- 11:26both shots i again i put the chemex
- 11:28filter at the bottom i put in the
- 11:29grounds i deep wdt'd coming up and then
- 11:32i
- 11:33did a slight tamp and with the porky
- 11:35press
- 11:36pressed it 180 pressed it with this
- 11:38design on the bottom okay
- 11:40same as what shea used and then i put a
- 11:43mesh filter on top i forgot to add that
- 11:45and i tamped it once more with the
- 11:46calibrated tamper for both of them all
- 11:48right so everything was exactly
- 11:49identical i pulled both shots now
- 11:52interestingly and i've already refracted
- 11:54them so the one with the porcupress came
- 11:56out in 42 seconds and that's using that
- 12:00slow bloom profile obviously it's gonna
- 12:02take a long time for that and then with
- 12:04the uh with the one without the porky
- 12:06press it came out in 43 seconds so it
- 12:09took one second longer now the
- 12:11differences in the extractions is where
- 12:13it's interesting with the one and i'm
- 12:15pulling a lot papaya last year's crop
- 12:17that i had frozen my freezer from
- 12:19lacabra the one with the porky press
- 12:21came out just over 24 extraction 24.1
- 12:25the one without it came out at
- 12:2823.22 percent extraction and it was one
- 12:31second longer so we're getting a
- 12:33higher extraction and just about just
- 12:35about the same amount of time which is
- 12:37really interesting and shay yet has
- 12:38another uh hypothesis there i've not
- 12:40done enough to really be able to
- 12:41corroborate that evidence but
- 12:43interesting to look at that article none
- 12:45the less that i have down the caption
- 12:46anyway let's get to tasting and we're
- 12:48gonna see if there is a difference
- 12:50between this one we use the porky press
- 12:53on and the one without all right here we
- 12:54go
- 12:57actually i should probably do the one
- 12:58without porky press first
- 13:08okay let me grab a sip of water
- 13:15all right
- 13:22okay well
- 13:25as always my tastings are more so a
- 13:26reflection of all the testing that i've
- 13:28already done i've pulled
- 13:29on this specifically i've pulled at
- 13:31least 40 or 50 by sides
- 13:34and again this this lines up with it i'm
- 13:36getting much more of that ripe fruit
- 13:38taste and sweetness coming out of the
- 13:40one i use a porky press with then the
- 13:41one without though they're both
- 13:43incredibly delicious shots that it seems
- 13:45that the porky press what it really does
- 13:47well is when it's really fine settings
- 13:49it can improve the extraction but for
- 13:51the most part it helps improve your
- 13:53consistency so regardless of what style
- 13:55shot you're pulling it's going to be
- 13:58it's not going to hurt
- 13:59the question is whether or not you
- 14:01should invest the amount of money these
- 14:02are like 250
- 14:03whether you should invest that amount of
- 14:05money to improve your espresso if you're
- 14:07someone that pulls normal shots no i
- 14:09would not recommend it if you're someone
- 14:11that every now and then pulls a flow
- 14:12profile shot no i would not recommend it
- 14:14even if you're someone that pulls
- 14:15frequently flow-profiled shots
- 14:18it depends on what you're looking for in
- 14:19your coffee if you want to squeeze out
- 14:20an extra percentage of extraction then
- 14:22this is likely for you if you want to
- 14:24push your if you're drinking really
- 14:26really lightly roasted coffees and you
- 14:28need help pushing the extraction then
- 14:29this could probably help you out a lot
- 14:31if you're someone let's see drinking
- 14:33medium roast something that's really
- 14:34soluble it's likely not going to do that
- 14:36much to your coffee so keep that in mind
- 14:39i i like this tool it will definitely be
- 14:41a part of my preparation whenever i'm
- 14:43dealing with really lightly roasted
- 14:44coffees and i'm trying to go with crazy
- 14:46high extractions but if you're doing
- 14:47anything that's coarse enough for a nine
- 14:49bar extraction or a turbo shot or
- 14:51anything along those lines it's too
- 14:53coarse for this to make a big difference
- 14:55at least in my experience as well as in
- 14:57shae's experience
- 14:59anyway i hope that was helpful if you
- 15:01you know if you have one of these around
- 15:03you know take take a look there's also a
- 15:05more budget-friendly one i didn't do or
- 15:07just testing with it but my friend
- 15:09dennis sabu out in austria has made a 3d
- 15:11printed one
- 15:13with a with sewing needles in it so you
- 15:15can check this out and see if it does
- 15:16something similar i'll be i'll be
- 15:18playing around with this soon now that i
- 15:19have all the data with the porky press
- 15:20but anyway thank you so much for
- 15:22watching this video again if you enjoyed
- 15:25it please you know drop a like subscribe
- 15:26check out my patreon check out the
- 15:28caption i have all my resources there i
- 15:30just want to thank you so much you all
- 15:31rock brew something tasty today and
- 15:34cheers
About this transcript
This page contains the full transcript of IS THIS $300 ESPRESSO TOOL WORTH IT?: The Porcupress Review by Lance Hedrick, generated from the public captions YouTube serves with the video. The transcript has 3,176 words across 462 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.