YouTube2Text

I Built a 20m Delta Loop for DX – Full DIY Build — Transcript

by MM0OPX Field Radio · 2,692 words · 379 segments · language en · Watch on YouTube

Full transcript

  1. 0:10I've had an interest in loop antennas
  2. 0:12for a long, long time. So when I go back
  3. 0:15to the start of my ham radio journey,
  4. 0:18I actually had a horizontal loop for 80
  5. 0:20m and it was a it was a fabulous antenna
  6. 0:23um and even at this QTH I even ran a
  7. 0:26sloping loop antenna um pretty much like
  8. 0:29a delta loop and it it ran down at 45
  9. 0:31degrees. And so for quite a quite a
  10. 0:34while I've actually been wanting to
  11. 0:35build another one. Now,
  12. 0:37as we're coming into the trough of the
  13. 0:40current solar cycle um we're going to
  14. 0:42need to rely on the higher bands and 20
  15. 0:45m is going to be our band of choice for
  16. 0:47DX before much longer. I know that 10 m
  17. 0:50is still opening, but give it another
  18. 0:52year or two and we're going to have to
  19. 0:54really come down um to 20 and perhaps
  20. 0:57even some of the lower bands. So
  21. 1:00an antenna that I've been wanting to
  22. 1:01build for a long time
  23. 1:03is a full wave delta loop for 20 m and
  24. 1:06in this video I'm going to show you how
  25. 1:08to build one and I'm going to show you
  26. 1:09one uh in use.
  27. 1:12Now I've created um a full documentation
  28. 1:15package um so this will allow you to
  29. 1:19build this without any fuss whatsoever
  30. 1:21and take um to take all the risk out of
  31. 1:24it.
  32. 1:25Now there's two versions of this guide.
  33. 1:27There's a standard version and there is
  34. 1:29an easy read version because if you're
  35. 1:31like me, I'm very much a kinesthetic
  36. 1:33learner. I like the easy read version.
  37. 1:35It's more pages,
  38. 1:37but [snorts] it's easier to use and work
  39. 1:39with. So at the center of this loop we
  40. 1:42actually have two 7 m DX Commander poles
  41. 1:45with the end sections removed.
  42. 1:48Now
  43. 1:50for a for a 20 m uh delta loop we need
  44. 1:53about 21 m of wire. It's slightly over
  45. 1:55that. [snorts] And so a 7 m pole seems
  46. 1:58ideal. Um but quite often, as is the DX
  47. 2:01Commander poles, the
  48. 2:07pole seems ideal.
  49. 2:10quite often,
  50. 2:12Now, the way that we can actually
  51. 2:14compensate for that is we can actually
  52. 2:15make the uh the gap at the bottom
  53. 2:18because we've got this apex down,
  54. 2:21we can actually make this more obtuse uh
  55. 2:23wider and that then makes the wire at
  56. 2:26the top a bit longer so we can actually
  57. 2:27fit in our our our full wave loop uh
  58. 2:30relatively easy.
  59. 2:32Now, I've done the calculations on this
  60. 2:35um and I just want to talk through how
  61. 2:36we've we've actually done this. So, I've
  62. 2:38made this really really simple um for
  63. 2:40what you need to do.
  64. 2:43Now, just before we go any further, why
  65. 2:45the delta loop? Well, if we actually
  66. 2:47look at the modeling and I know that
  67. 2:49modeling isn't everything, um we
  68. 2:51actually have some good advantages over
  69. 2:54a dipole and a ground mounted vertical
  70. 2:56in certain situations.
  71. 2:58Now, a ground mounted vertical has unity
  72. 3:00gain, it has it it has even gain all the
  73. 3:03way roundabout it, [snorts] whereas a
  74. 3:05delta loop, it favors broadside to it.
  75. 3:07So, a bit like a dipole,
  76. 3:09but we get more gain um uh over a dipole
  77. 3:13at the same height. Um
  78. 3:15the delta loop as well because um a lot
  79. 3:18of the current is on the top of the
  80. 3:19wire, if we have that feed point
  81. 3:21relatively low, say three or four meters
  82. 3:23off the ground,
  83. 3:24remember that the top of that wire uh is
  84. 3:26another three or four meters above that,
  85. 3:29which is a bit harder to do with a
  86. 3:31dipole and it's twice as much wire in
  87. 3:33the air.
  88. 3:34So, it's a real um I think it's a real
  89. 3:37advantageous antenna if you can actually
  90. 3:39uh build one. Right, so getting back to
  91. 3:41the build,
  92. 3:42for the base plate that we have this, we
  93. 3:44need something to mount the poles to.
  94. 3:46So, I've done it very simply. So, I've
  95. 3:48designed a base plate to suit whatever
  96. 3:51clamps, whatever poles that you can
  97. 3:52actually get a hold of
  98. 3:54and you simply print this out in A4
  99. 3:56format. Just print it out in 100% scale.
  100. 4:00It's as simple as that. My cheap uh HP
  101. 4:03printer, it does it absolutely fine. It
  102. 4:04didn't even print the whole thing out
  103. 4:06because it has
  104. 4:07It doesn't it doesn't allow narrow
  105. 4:08margins,
  106. 4:09but it was enough to get me going. And
  107. 4:11once you print it out, you simply trim
  108. 4:13the top and bottom edge,
  109. 4:16and then you then need to stick stick
  110. 4:17that onto the plate that you're going to
  111. 4:19use. Now the plate that I'm going to use
  112. 4:21is 12 mm thick or 1/2 in
  113. 4:25exterior plywood, which is more than
  114. 4:27strong enough for this build.
  115. 4:30If you're going You could even use 18 mm
  116. 4:32ply. If you use marine ply, even better.
  117. 4:35Perhaps if you want to push the boat
  118. 4:36out, you could actually then use
  119. 4:38aluminium plate, but that's be going to
  120. 4:40make it a bit more expensive. The
  121. 4:42plywood option is really really cheap.
  122. 4:44You just need to remember after cutting
  123. 4:46it, just give it a paint um or a varnish
  124. 4:48to seal all the edges up.
  125. 4:51So we take our uh we take our printed
  126. 4:54out template that's been cut out and we
  127. 4:55simply stick it on our uh piece of
  128. 4:58plywood or aluminium, whatever you're
  129. 5:00going to use. We then uh we do that we
  130. 5:02just do that with a bit of Pritt Stick,
  131. 5:04PVA glue.
  132. 5:06We then um we then just mark all the
  133. 5:08holes that we need to drill. That's to
  134. 5:10suit our mast. My mast has a 25 mm at
  135. 5:13the top the top of it. So that's what
  136. 5:15I'm going to use. These go on the back
  137. 5:16of it. Um and we need to actually drill
  138. 5:20um so the so the two sets of holes that
  139. 5:22is
  140. 5:2242° from the center. Now
  141. 5:26Callum actually sells uh a GRP
  142. 5:28fiberglass ground post to go with these
  143. 5:317 m poles. So that's what I've used
  144. 5:33here. I've got one of these um and I
  145. 5:36think it's about 1.1 m in total length.
  146. 5:39And what I've done is I've actually cut
  147. 5:41this uh in two,
  148. 5:43and that forms the stub stub masts. So
  149. 5:46our 7 m poles simply slide over the top
  150. 5:48of these, nice and neat. Right, back to
  151. 5:51the uh back to the plate.
  152. 5:53We've stuck our template on the uh
  153. 5:55plywood.
  154. 5:56Uh we then need to
  155. 5:58I like to center punch it, and then
  156. 6:00we'll pilot drill all the holes about 3
  157. 6:01mm,
  158. 6:02[clears throat] excuse me,
  159. 6:04and then we will then drill them uh 6.5
  160. 6:07mm because I'm going to be using a M6
  161. 6:10bolt here or you could use quarter inch
  162. 6:12if you're across the pond.
  163. 6:14So we drill all our holes. We um we'll
  164. 6:17maybe put a little counter sink on them.
  165. 6:19We'll use some sandpaper. We'll smooth
  166. 6:21off all the edges and that's our
  167. 6:22template uh built. As I say you can give
  168. 6:24it a paint if you want.
  169. 6:26Um I did on my original one but I had to
  170. 6:28remake it because I had a problem with
  171. 6:30the tension but you won't have such
  172. 6:31problems if you use these poles, this
  173. 6:34template, everything will tension up.
  174. 6:37We then um we then assemble our plate.
  175. 6:40We get these um
  176. 6:42these clamps. I've got lots of these
  177. 6:43here. I bought these in a in a number of
  178. 6:45sizes um but the ones that we are using
  179. 6:47are uh they are 32 mm uh uh clamps.
  180. 6:52And within the documentation it even
  181. 6:54gives you ordering codes and everything.
  182. 6:56So
  183. 6:57columns, you know, the two halves of
  184. 6:59these stub masts that are cut into I
  185. 7:01just put a layer of tape on them because
  186. 7:03they're about 31.7
  187. 7:05that takes them up to 32 and then we fit
  188. 7:07them. After we've assembled all the
  189. 7:09plate up we then fit the stub masts into
  190. 7:11it.
  191. 7:13Um on the back side we then fit our 25
  192. 7:15mm stubs which is here which is these
  193. 7:18and these these this will allow us to
  194. 7:20use this antenna on my Yemo 11 m mast
  195. 7:23although I don't put it up that high.
  196. 7:26So that's that that fits onto that.
  197. 7:28We then need to prepare the wire
  198. 7:30um the the exact measurements are in the
  199. 7:33the the documentation but it's just over
  200. 7:3521 m.
  201. 7:36Um we cut that exactly, pre-stretch it
  202. 7:39um now I'm using DX10 wire because it's
  203. 7:41nice and supple. Again you can get that
  204. 7:42from DX Commander but you can use
  205. 7:45whatever you have to hand. The velocity
  206. 7:46factor may change slightly but it won't
  207. 7:48be enough.
  208. 7:49[snorts]
  209. 7:50So you cut
  210. 7:52uh uh measure it out, make give it a bit
  211. 7:53of a stretch um
  212. 7:55and then you need to terminate it with
  213. 7:57uh M4 uh ring connectors. Take the what
  214. 8:00to do is take the
  215. 8:02the outer plastic coating off, crimp it,
  216. 8:04solder it, put some heat shrink on it.
  217. 8:07And on our on our poles, um the two end
  218. 8:11caps that are on the poles, you could
  219. 8:12I've actually put a little slot in it
  220. 8:14and I've put a hole through it.
  221. 8:15And this is so we can keep the wires
  222. 8:17assembled to the poles, which makes it
  223. 8:19easier.
  224. 8:21So, um very important note that we need
  225. 8:24to actually put we need to form a little
  226. 8:26loop on the end of our uh wires at each
  227. 8:29end, but before we do that, we need to
  228. 8:31thread the wires um
  229. 8:33through the poles. But before we even do
  230. 8:35that, we need to add a little bit of
  231. 8:37heat shrink to the end of the poles.
  232. 8:39This is optional, but I just want to add
  233. 8:41on a little bit strain relief. So, after
  234. 8:43we've put our little bit of heat shrink
  235. 8:44on the second last section, which is our
  236. 8:47top new top section now, we then thread
  237. 8:49the ring connector, terminated ring
  238. 8:51connector off each end of the wire
  239. 8:52through each of the poles straight
  240. 8:54through to the bottom.
  241. 8:56Once we've then done that, we then can
  242. 8:58put our little loop at uh after putting
  243. 9:00a bend at 100 mm, put a couple of cable
  244. 9:03ties on there.
  245. 9:04And [snorts] these loops will actually
  246. 9:06then hook onto our base plate. Um
  247. 9:09again, it's all in the documentation.
  248. 9:13So, once we've done that, we've got the
  249. 9:15poles, we've got the wire,
  250. 9:17it can then fit onto the base plate.
  251. 9:19Now,
  252. 9:20uh a delta loop has got an impedance at
  253. 9:23resonance without any matching four to
  254. 9:26ones, etc. It's got an impedance of
  255. 9:28roundabout 200 ohms. That's resonance
  256. 9:31where we've got zero reactance.
  257. 9:33[snorts] Um it won't be exact, but it'll
  258. 9:35be it'll be roughly. So, that's what
  259. 9:37I've did and that's why I've came to the
  260. 9:38length of this 21.05 because that's
  261. 9:41that's given me a happy medium depending
  262. 9:43if the antenna is 2 m off the ground or
  263. 9:45is it up seven or eight m off the
  264. 9:47ground.
  265. 9:49Now, I've went with a dedicated LC match
  266. 9:52option because that's the materials that
  267. 9:54I have to hand and I want [snorts] this
  268. 9:57to be a monoband antenna.
  269. 10:00So, I actually didn't even use SIM NEC.
  270. 10:03I used Claude to do the calculations. It
  271. 10:05meant I didn't need to um go away into
  272. 10:07the computer and Claude's calculations
  273. 10:09were absolutely perfect. It told me um
  274. 10:12exactly um how much inductance I needed
  275. 10:14the coil to be. It told me um uh how
  276. 10:17much uh capacitance was needed for the
  277. 10:20little capacitor and I've made this
  278. 10:22really simple matchbox. So really easy
  279. 10:25um and this will actually handle QRO no
  280. 10:28problem at all.
  281. 10:30So once I actually got this up in the
  282. 10:32air and I connected this little matchbox
  283. 10:34voila it was it's amazing when you see
  284. 10:37these matches working um and I got
  285. 10:39effectively got pretty much a
  286. 10:42a sweet spot right in the middle of the
  287. 10:43band um with a very low SWR.
  288. 10:46We don't worry about SWR too much as
  289. 10:48long as it's less than two to one across
  290. 10:50the band that's absolutely fine.
  291. 10:53Now within the documentation you there's
  292. 10:55a number of ways that you could do this.
  293. 10:56If you're new to the hobby or you want
  294. 10:58to have some multi-band operation go out
  295. 11:00and buy yourself a nice four to one
  296. 11:02balun
  297. 11:03and just use that connect it up and it
  298. 11:05will work absolutely fine.
  299. 11:07And I haven't tested that option. Also
  300. 11:09you could you could use uh a section of
  301. 11:11twin um twin lead of um 50 ohm coax.
  302. 11:15There's a diagram how to do that. There
  303. 11:17is an option for 75 ohm coax as well for
  304. 11:20a quarter length
  305. 11:21but
  306. 11:23this this can be done whatever way that
  307. 11:25you want to do it but I like I'm
  308. 11:26currently I'm enjoying using
  309. 11:29this little LC match here um
  310. 11:33beyond below that I've actually got a
  311. 11:35one to one choke. This is a GM3 SEK
  312. 11:38design for his high bands and this
  313. 11:40actually works. This is this is to
  314. 11:42provide quite a high level of choking
  315. 11:44impedance uh 20 m through 10 so it works
  316. 11:47fine and it's easy just to connect to
  317. 11:49the box. We just screw that on here and
  318. 11:51we just screw our coax on the other side
  319. 11:53and then we're actually good to go. Now
  320. 11:56how does it perform well? I've got
  321. 11:58limited testing yesterday morning I
  322. 12:00hooked it up about 11:00 um
  323. 12:03and I faced it northwest southeast so
  324. 12:06pointing towards Europe and pointing
  325. 12:08towards the States and I had a great
  326. 12:10time. I worked all over Europe. I had a
  327. 12:12little pile up going. I think I worked
  328. 12:14about 30 or 40 stations. And getting to
  329. 12:17the end when I had to come off, I had
  330. 12:19I had Danny across in North Carolina. He
  331. 12:21gave me a call, so that was wonderful.
  332. 12:23So it proves that the antenna's working.
  333. 12:25And I mean, that's not absolutely
  334. 12:26everything. This will be a really nice
  335. 12:28DX antenna depending on where you have
  336. 12:31it mounted, whether you have it mounted
  337. 12:32low down or or higher up. If you can get
  338. 12:35it higher up, that's all the better.
  339. 12:38So this is an antenna that I'm going to
  340. 12:40be using as we get into the trough of
  341. 12:42the solar cycle. Um and I'm going to use
  342. 12:44it more and more. And I may multi-band
  343. 12:47it. I may modify it. There's there's
  344. 12:48some mods that you can do to it. You can
  345. 12:50feed it with ladder line, etc etc. And
  346. 12:53we'll see how it's
  347. 12:54it's going to perform. But a thoroughly
  348. 12:56easily build a easy easy to build. And
  349. 12:59and I would recommend anyone to build it
  350. 13:01even beginners. I mean, you just need um
  351. 13:04you just need basic tools. And you can
  352. 13:07even go into like hardware stores. We've
  353. 13:08got one here called B&Q where you could
  354. 13:11pick up your piece of plywood off the
  355. 13:12shelf and they will cut it for you. I
  356. 13:14think they'll they'll almost cut it for
  357. 13:15you free of charge. They give you two or
  358. 13:18three free cuts and then and following
  359. 13:19cuts are something like 50 pence.
  360. 13:22Really really cheap to do. Or you could
  361. 13:24just buy a piece of aluminium and you
  362. 13:26can drill it yourself. So
  363. 13:28uh uh a drill's about the most complex
  364. 13:30tool that you actually need to build
  365. 13:32this antenna. Everything is absolutely
  366. 13:34pre-tensioned. The poles have a nice bit
  367. 13:35of tension on them. I've done all the
  368. 13:37work for you. Um so yeah. So links down
  369. 13:40in the the description if you want to
  370. 13:42have a look at that guide and you want
  371. 13:43to build this antenna for yourself,
  372. 13:45please have a go. Let me know how you
  373. 13:47get on with it. If there's anything up
  374. 13:49with the documentation or you think that
  375. 13:51I've missed, I'll be more more than
  376. 13:53happy to to up rev the documentation
  377. 13:55with those changes. Okay. Let me know
  378. 13:57how you get on guys and we'll catch you
  379. 13:59in the next one. Bye for now.

About this transcript

This page contains the full transcript of I Built a 20m Delta Loop for DX – Full DIY Build by MM0OPX Field Radio, generated from the public captions YouTube serves with the video. The transcript has 2,692 words across 379 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.