How to Identify Common Hose Failures and Causes? | ParkerStore — Transcript
Full transcript
- 0:01[Music]
- 0:20hi it's mike from the parker store
- 0:23in this partner with parker store video
- 0:25we're going to talk about hydraulic hose
- 0:26failures the most common things that go
- 0:28wrong with hoses the likely causes and
- 0:31how to address each of these situations
- 0:34it should be noted that even in optimal
- 0:36conditions and in cases where hose
- 0:37assemblies were properly made the life
- 0:40expectancy of any hose assembly is
- 0:42directly related to the operating
- 0:44parameters of the application
- 0:46but when a host fails it is often the
- 0:48result of some form of human error
- 0:50misapplication improper usage or
- 0:52improper maintenance
- 0:54let's look at some of the most common
- 0:55hydraulic hose issues
- 0:57first off you've got your burst hose
- 1:00where the wire reinforcement failed in
- 1:02the braid along the outside of the hose
- 1:04this can happen when a hose has simply
- 1:05lived out its service life but it can
- 1:07also be the result of a high number of
- 1:09pressure cycles or continuous flexing of
- 1:12the hose in that one area
- 1:14there's nothing to do here but review
- 1:15the application replace the assembly and
- 1:18develop a preventative maintenance
- 1:19schedule
- 1:21here's another kind of burst hose where
- 1:22it bursts near the fitting along with
- 1:24signs of corroded wire but with no
- 1:26obvious cover damage
- 1:28you'll see the hose leaks that could
- 1:30look like a pinhole or maybe just an
- 1:32escape of moisture called weepage or
- 1:34there might be bubbles near the fitting
- 1:36which may contain fluid this happens
- 1:38when the hose inner tube was cut or
- 1:40damaged during the fitting assembly
- 1:42possibly due to a lack of proper
- 1:43lubrication
- 1:45when the fitting is improperly assembled
- 1:47like that it allows moisture to enter
- 1:48around the socket of the fitting which
- 1:50corrodes reinforcement wires
- 1:52you've got to replace the hose assembly
- 1:54making sure you review proper assembly
- 1:56techniques
- 1:57sometimes you see hoses like this one
- 2:00which is burst at the fitting along with
- 2:02broken wires at the last shell grip or
- 2:04sometimes at the end of the nipple
- 2:07this happens when the hose continuously
- 2:09moves or pulls at the fitting
- 2:11excessive movement may be the result of
- 2:13pressure surges or the hose assembly
- 2:15length being too short or the hose bend
- 2:18may begin too close to the fitting
- 2:20yet another cause may be incorrect crimp
- 2:22dimension
- 2:24fix it by lengthening or rerouting the
- 2:26assembly to allow for some slack
- 2:28never stretch to fit as assemblies may
- 2:30shorten when pressurized before starting
- 2:32to bend it the hose should be routed
- 2:35straight for at least two times the
- 2:36inside diameter of the hose
- 2:38clamp the assembly as necessary to avoid
- 2:41movement
- 2:42review crimping techniques and proper
- 2:44tooling
- 2:46next issue when the fitting blows off
- 2:49this occurs when the hose wasn't
- 2:50inserted into the shell of the fitting
- 2:52per the recommended length which means
- 2:54all the grips aren't being used
- 2:57all the grips in the shell are needed to
- 2:58hold the fitting onto the hose
- 3:00in fact the last grip in the shell does
- 3:02about a quarter of the work in holding
- 3:04the fitting to the hose
- 3:06in such cases you simply have to replace
- 3:08the hose assembly and before inserting
- 3:10the fitting make sure you mark the cover
- 3:12of the hose per the recommended value
- 3:14stated in our catalog then insert the
- 3:16fitting to the end of the shell lines up
- 3:18to your mark
- 3:19okay now here's another way the fitting
- 3:21can blow off when the assembly leaks
- 3:23between the shell of the fitting and the
- 3:25hose
- 3:25this can happen when the shell of the
- 3:27fitting is either under or over the
- 3:29recommended crimp specifications
- 3:31you just got to replace the hose
- 3:32assembly checking for proper fitting
- 3:34usage
- 3:36and make sure you review the crimping
- 3:37instructions for the particular crimper
- 3:39being used including proper tooling
- 3:42now sometimes you'll get external damage
- 3:44to the hose cover the hose actually
- 3:47bursts around an area where there's an
- 3:48obvious twist in the hose you'll also
- 3:50see some broken wires
- 3:52this occurs when the hose gets an
- 3:54unwanted twist during the assembly of
- 3:56the fitting due to a lack of proper
- 3:57lubrication
- 3:59you have to review proper hose assembly
- 4:01procedures and replace the hose assembly
- 4:04you may also have to use clamps to
- 4:06reroute the hose using the hose lay line
- 4:08as a guide to assure that the hose
- 4:10flexes in one plane okay here's a case
- 4:12where the cover has foreign object
- 4:14damage and or abrasion
- 4:16reinforcement wires show signs of being
- 4:18rubbed and possibly torn and corroded
- 4:21this is from excessive rubbing or
- 4:23chafing of the hose against an external
- 4:25object possibly other hoses or the wrong
- 4:27size clamp or perhaps from the impact of
- 4:30the hose on sharp corners or brackets
- 4:32this calls for replacing the hose
- 4:34assembly
- 4:35use a protective sleeve or hose guards
- 4:38reroute the hose assembly and if
- 4:39appropriate use proper sized clamps to
- 4:41avoid contact with other objects
- 4:44sometimes when fluid is emitted at a
- 4:46high velocity from an orifice and hits
- 4:48the inner tube
- 4:49erosion happens and eventually the inner
- 4:51tube is gouged through to the wire braid
- 4:53for several inches
- 4:55causing the hose to spring a big leak
- 4:58the erosion can also be caused by
- 4:59particles in the fluid
- 5:01but the cause here might still be traced
- 5:03to the hose assembly like if it's bent
- 5:06too tightly for proper flow or if the
- 5:08fluid medium is too abrasive for that
- 5:10particular inner tube in any case you've
- 5:12got to replace the hose assembly
- 5:14next issue on our list when the hose
- 5:17bore appears to be restricted the tube
- 5:19may be torn or may have broken loose
- 5:21from the reinforcement and piled up at
- 5:22the end of the assembly resulting in a
- 5:24reduced flow or maybe no flow at all
- 5:27in these cases the outside of the hose
- 5:29may show signs of being flattened
- 5:32this comes down to vacuum failure the
- 5:34hose may have been kinked flattened or
- 5:36bent too sharply in some cases it may be
- 5:39due to poor adhesion or insufficient
- 5:41cure of the inner tube
- 5:42replace with a hose rated for the
- 5:44specific vacuum application sometimes
- 5:47pressure issues cause a hose to burst
- 5:50maybe in a number of places these are
- 5:52usually clean bursts with no random wire
- 5:54breakage and no sign of wire on wire
- 5:56abrasion or cover abrasion
- 5:58this is usually caused by excessive
- 6:00pressure or pressure in the range of the
- 6:02minimum burst rating for the hose
- 6:04you can adjust the system pressure to be
- 6:06within the established working pressure
- 6:08of the hose or replace with a hose with
- 6:10a higher working pressure than the
- 6:12system pressure
- 6:13and don't forget to include pressure
- 6:15spikes when choosing the psi of your
- 6:17hose
- 6:18then there are the effects of cold
- 6:20hoses exposed to temperatures below
- 6:22their recommended limits during hose
- 6:24movement
- 6:25what you'll see is the inner tube and or
- 6:27the cover has cracks but it's soft and
- 6:30flexible at room temperature
- 6:32to address this issue review the
- 6:34application and raise the temperature to
- 6:36within the boundary specified or replace
- 6:39with a hose recommended for the given
- 6:40temperature parameters
- 6:42conversely there are heat cost issues
- 6:45the hose will be hard brittle and crack
- 6:47when flexed at room temperature
- 6:49on its cover there may be visible signs
- 6:51of being dried out and charred
- 6:53so in these cases you know that the hose
- 6:55was exposed to heat in excess of the
- 6:57recommended value
- 6:58what's happened is aerated oils have
- 7:00caused oxidation in the hose's inner
- 7:02tube making the hose harden
- 7:04any combination of oxygen and heat will
- 7:06accelerate the hardening of the inner
- 7:08tube
- 7:09the same effect may be caused by
- 7:10cavitation the formation of empty spaces
- 7:13within the material plus plain old age
- 7:15can also create these symptoms
- 7:18if your hose isn't near or beyond its
- 7:20service life review the application and
- 7:22lower the temperature to within your
- 7:23hose's working limits or replace the
- 7:26hose with one that has a qualified
- 7:27temperature rating install heat guards
- 7:30or shields as required
- 7:32if you find that your hose's inner tube
- 7:34contains numerous fine cracks it remains
- 7:36flexible and no cracks are found in the
- 7:38hose under the fittings then the
- 7:40internal air may be too dry probably due
- 7:43to the use of a lube-free compressor or
- 7:45refrigerated air drying system
- 7:47replace this hose assembly with one that
- 7:49is rated for extreme dry air
- 7:52fluid can also be incompatible with just
- 7:54the inner tube which can badly
- 7:55deteriorate the inner tube as you see
- 7:57here
- 7:58it may also show signs of swelling and
- 8:00delamination
- 8:02in some cases the inner tube may be
- 8:03partially washed out
- 8:05again you need to replace the hose
- 8:07assembly with a hose that's compatible
- 8:08with the fluid to be used or replace the
- 8:11fluid with one that is compatible with
- 8:12the hose material
- 8:14check out our stamp video for additional
- 8:17information on selecting the right hose
- 8:19for your specific application
- 8:21if you have any questions about assembly
- 8:23techniques or bending talk to your
- 8:25parker store professional or find our
- 8:27hose installation and routing video on
- 8:29youtube
- 8:30also talk to your parker store
- 8:32professional about extending the life of
- 8:33the hose in your application
- 8:36if you're looking for sleeving options
- 8:38your parker store professional can help
- 8:39you get the best protection for your
- 8:41hose
- 8:42i hope this video has helped you in your
- 8:44understanding of how hose issues are
- 8:46caused how to address them or better yet
- 8:48avoid them all together
- 8:50we hope also that it's clear how crucial
- 8:52it is to ensure you have the correct
- 8:54hose assembly and that it's set up in
- 8:56the proper manner
- 8:57remember you can always turn to the pros
- 8:59at your parker store they'll make sure
- 9:01you have the product that's right for
- 9:02your application and answer any
- 9:05questions you might have
About this transcript
This page contains the full transcript of How to Identify Common Hose Failures and Causes? | ParkerStore by Parker Hannifin | Products and Support, generated from the public captions YouTube serves with the video. The transcript has 1,629 words across 267 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.