YouTube2Text

Festo MPS Station Overview — Transcript

by M Hanbury · 2,645 words · 458 segments · language en · Watch on YouTube

Full transcript

  1. 0:28so
  2. 0:42uh
  3. 0:49okay first of all we have three
  4. 0:51different systems here one in the left
  5. 0:53middle right and they each perform a
  6. 0:55specific function
  7. 0:57the first one is the stack magazine it's
  8. 0:59holding the
  9. 1:00the parts that are eventually going to
  10. 1:02be distributed the second the middle one
  11. 1:04is called the joining system
  12. 1:06it's going to join the part with the cap
  13. 1:10and then the third one the one over on
  14. 1:12the right has
  15. 1:13three shoots one where the part either
  16. 1:15goes down
  17. 1:16international national or gets rejected
  18. 1:19and it's positioned to the correct shoot
  19. 1:22with these two
  20. 1:23actuators here and they're electrically
  21. 1:25controlled they don't happen to be
  22. 1:26pneumatic they're electrically
  23. 1:28controlled and as well in the system
  24. 1:30you'll see these three boxes
  25. 1:32one here one in the middle and one on
  26. 1:35the left
  27. 1:35and if everything's working okay there's
  28. 1:37actually a green light that's on in the
  29. 1:39top of the box
  30. 1:40and those boxes are used to control the
  31. 1:43conveyor belt the conveyor belt can be
  32. 1:45stopped
  33. 1:46reversed or in a forward position
  34. 1:49and at the same time while we're looking
  35. 1:51at the system here you can see that
  36. 1:53these are the devices that either read
  37. 1:56rfd codes
  38. 1:58or write rfd codes and they're used to
  39. 2:01positioned it down the correct chute
  40. 2:04now the communications for all of those
  41. 2:07rf devices
  42. 2:08are used uh have industrial
  43. 2:10communications and you can see
  44. 2:12that these boxes here are the
  45. 2:14communications for all of that rf device
  46. 2:17and it eventually gets back to the
  47. 2:18computer through an ethernet controller
  48. 2:21and that's the way all those things are
  49. 2:23con sending its information back
  50. 2:26to the computer now the next part i want
  51. 2:28to show you has to do with the
  52. 2:30arrangement of the keys the push buttons
  53. 2:32and how you reset
  54. 2:34and clear everything so i'm going to
  55. 2:36start off with everything off
  56. 2:40okay and if you look over in the back
  57. 2:43you'll see that the yellow
  58. 2:45and red light are turned on right now so
  59. 2:47that's an indication that the system is
  60. 2:49not
  61. 2:50ready to perform any particular test
  62. 2:53now generally i found it works the best
  63. 2:56if you reset the system
  64. 2:58starting on the right hand side moving
  65. 3:00towards the left hand side
  66. 3:02and note how these are connected
  67. 3:03together that's kind of important as
  68. 3:05well
  69. 3:07the black and the blue wires but we're
  70. 3:08going to start off with the
  71. 3:10keys in a horizontal position and
  72. 3:13starting from the right hand side
  73. 3:15i'm going to pull this up and i'm going
  74. 3:18to press the reset button
  75. 3:19you actually may hear a pneumatic sound
  76. 3:22or belt turning but it's resetting that
  77. 3:24particular station
  78. 3:25so i press reset and yeah i heard a
  79. 3:28solenoid change and then i'm going to
  80. 3:30bring the key up to the
  81. 3:31upward position or vertical and then
  82. 3:34press the start button so that station
  83. 3:36is now ready
  84. 3:37moving on to the middle station i'm
  85. 3:40going to make sure that that button is
  86. 3:41pulled out
  87. 3:42press the reset button and you can hear
  88. 3:46that a belt turn for a few seconds just
  89. 3:49kind of initializing everything
  90. 3:51bring these the key switch to the
  91. 3:53vertical position
  92. 3:54press the start button and that system
  93. 3:57is ready
  94. 3:58and now finally over on the third system
  95. 4:01the push button was released brought
  96. 4:04outwards the reset
  97. 4:05is indicating as being ready press it
  98. 4:09bring the key to that position and then
  99. 4:12press the
  100. 4:12reset and there was already an order in
  101. 4:16the system so
  102. 4:17normally the light would flash green
  103. 4:19everything seems to be working as it
  104. 4:20should
  105. 4:21it's putting a cap on the red sometimes
  106. 4:23it gets stuck right here so you have to
  107. 4:25move this along
  108. 4:28[Music]
  109. 4:30and that one didn't work out so well but
  110. 4:33that's that's okay
  111. 4:36and those are the when you see the rfid
  112. 4:39lights flashing
  113. 4:40it's an indication that it's either
  114. 4:42reading
  115. 4:43or writing at that particular time okay
  116. 4:46be aware of how these three systems are
  117. 4:49interconnected together with that black
  118. 4:51and blue wire
  119. 4:52and down all the way to the bottom is
  120. 4:54the siemens plc
  121. 4:56it's an s7 1500 semantic plc
  122. 5:00and that's what's running the the
  123. 5:02process and actually
  124. 5:04you see all of the lights on there up on
  125. 5:06the the plc you'll see a bunch of lights
  126. 5:08those lights indicate the status of the
  127. 5:11inputs and the outputs and there's an
  128. 5:12analog module
  129. 5:14as well make sure that the power is on
  130. 5:16make sure
  131. 5:17those two cables are connected a blue
  132. 5:19light comes on for the power
  133. 5:21and there's another separate cable for
  134. 5:23the 24 volt supply that needs to be
  135. 5:25plugged in as well
  136. 5:26now we're also going to go around to the
  137. 5:28back to have a look at some of the
  138. 5:30connections in the back
  139. 5:32we're going to look at all the different
  140. 5:34systems in the back you can see that
  141. 5:36basically there are different
  142. 5:38controllers up in the top shelf and on
  143. 5:40the very right hand side
  144. 5:42is the computer as the computer is
  145. 5:44connected to the mouse and the monitor
  146. 5:46and the keyboard and it's running that
  147. 5:49software that is the industry 4.0
  148. 5:52that's controlling each of those three
  149. 5:55plc's
  150. 5:56independently so you have one pc program
  151. 5:58communicating with three
  152. 6:00programmable logic controllers and all
  153. 6:02the hardware is in the back
  154. 6:04so you want to make sure the power is on
  155. 6:06all the lights that should be on
  156. 6:07and down at the floor it's kind of messy
  157. 6:10but those are all the pneumatic
  158. 6:12connections
  159. 6:13and that metal box is actually the
  160. 6:15pneumatics distribution
  161. 6:17connection point so about 60 psi
  162. 6:20or six psi comes into the system it's
  163. 6:23regulated with three
  164. 6:24regulators on the panel but that's just
  165. 6:26a distribution
  166. 6:33okay this is a this is called an
  167. 6:35industry 4.0 system
  168. 6:38and it's used to study mechatronics and
  169. 6:40there are many sensors and actuators on
  170. 6:42this system
  171. 6:43and we're going to look at the software
  172. 6:44configuration first of all
  173. 6:46so you have to run this mini mes
  174. 6:49communications tool first
  175. 6:51and it's critical that all of these four
  176. 6:53blue check marks
  177. 6:55are blue i think they're grayed out when
  178. 6:57they're not active but they all have to
  179. 6:59be blue
  180. 7:00and to get it to work you usually have
  181. 7:02to do a refresh so there is a
  182. 7:04button here up here and i believe
  183. 7:08if you click on these buttons too but in
  184. 7:10the final
  185. 7:11when you complete everything you have to
  186. 7:13make sure that these four buttons
  187. 7:15are in blue these two other boxes here
  188. 7:18indicate
  189. 7:19the string that's applied to the rfid
  190. 7:22sensor
  191. 7:23that's inside the object as it's moving
  192. 7:25along the conveyor belt
  193. 7:26one of these boxes indicates the string
  194. 7:29it's reading and the other box indicates
  195. 7:32the string
  196. 7:32it's outputting so it's worth monitoring
  197. 7:35those as you're
  198. 7:36working with the system once you've got
  199. 7:38all of that set up
  200. 7:39then you're going to move to the second
  201. 7:42screen
  202. 7:42which allows you to configure the system
  203. 7:45the product and the order
  204. 7:47and there's also order history but
  205. 7:48that's not really required for this
  206. 7:50system
  207. 7:51the other thing that you must do before
  208. 7:54any of that
  209. 7:54actually is the system configuration
  210. 7:58and this particular system has three
  211. 8:00stations
  212. 8:01one of the stations is called the stack
  213. 8:04magazine and that's where the parts are
  214. 8:05held
  215. 8:06the second one is called the joining
  216. 8:08system and that's where the cap
  217. 8:10is placed on top of the object and it
  218. 8:13uses
  219. 8:14pneumatics to do that and then the third
  220. 8:17system
  221. 8:18is called sorting and that's to either
  222. 8:20apply the part to
  223. 8:22national distribution international
  224. 8:24distribution or rejecting it
  225. 8:27through the third slot that it can go
  226. 8:30down so you have to set that
  227. 8:31up by clicking stack first
  228. 8:34join second and sorting third and it
  229. 8:37tells you in this box that there are
  230. 8:39three systems you also want to make sure
  231. 8:41before moving any further that these
  232. 8:43three boxes
  233. 8:44are blue they're partly used for
  234. 8:47communications if they're not
  235. 8:48highlighted
  236. 8:49the system won't work the next tab
  237. 8:52is to set up what you want to do with
  238. 8:55each part
  239. 8:56and you can see i have different
  240. 9:00programs here release red release block
  241. 9:03and so on
  242. 9:04and you give each of those a name so the
  243. 9:06first one here is called
  244. 9:08red cap cc id and it has
  245. 9:11three steps it releases the red work
  246. 9:14piece
  247. 9:14from the holding station it mounts a cap
  248. 9:18and there's an abbreviation for each of
  249. 9:19those commands and you actually see that
  250. 9:22inside the rfid
  251. 9:25so release the work piece mount the cap
  252. 9:28check the color you're really just
  253. 9:29verifying the color
  254. 9:31and then in this case it's going to send
  255. 9:33it down the
  256. 9:34center slot which is the international
  257. 9:37distribution
  258. 9:38and there's a code for each of these
  259. 9:40things so
  260. 9:41i think i think you can just go by the
  261. 9:44code here this is release red so rr
  262. 9:46mount cap mc check color is cc
  263. 9:50and then s i
  264. 9:54i guess the second letter there refers
  265. 9:56to international so i had one for
  266. 9:58the block one for the red
  267. 10:01and one for other functions as well
  268. 10:06so those are the names but you set that
  269. 10:08up one time and you're going to use that
  270. 10:10information in the order management
  271. 10:12so the last part is the order management
  272. 10:14and you can see
  273. 10:15these are all the available products and
  274. 10:18i've chosen to
  275. 10:19go with a red cap so it's red cap
  276. 10:23check color and international
  277. 10:26and then the second one is a black part
  278. 10:29put a cap on it
  279. 10:30check its color and then send it down to
  280. 10:33international
  281. 10:35the third one actually doesn't check the
  282. 10:37color it's a red part
  283. 10:39so i don't think it would matter with
  284. 10:41this one because it's not checking the
  285. 10:42color
  286. 10:42it's not going to place a part on it and
  287. 10:45it's going to go down
  288. 10:46through the national one kind of unique
  289. 10:48and tricky thing with the software as
  290. 10:50well
  291. 10:51is if you want to remove one of the
  292. 10:53previous orders because it won't work
  293. 10:55until you remove a previous order
  294. 10:57you actually have to select the order
  295. 10:59number
  296. 11:00in this box and then do subtract or
  297. 11:03minus
  298. 11:04and then that order goes away and then
  299. 11:07to automatically begin the process
  300. 11:09you're going to be clicking on the plus
  301. 11:11symbol
  302. 11:12and that will automatically start the
  303. 11:15system
  304. 11:17i hope that helps and uh for for all of
  305. 11:20this to work you actually have to attach
  306. 11:22a keyboard and a mouse to the two usb
  307. 11:25ports and there are
  308. 11:26extra usb ports in the back of the
  309. 11:28computer
  310. 11:35all right what i'm going to show you
  311. 11:36right now is how to set up all of the
  312. 11:38parts to be able to run through the
  313. 11:40process that we just did with the
  314. 11:42software and you can see that there are
  315. 11:44three shoots here
  316. 11:45national international and the third
  317. 11:48shoot is kind of a reject shoot
  318. 11:50and oats each of those things is
  319. 11:52controlled by an
  320. 11:54actuator arm it's pneumatically
  321. 11:55controlled right here
  322. 11:57and this will open or close with a
  323. 12:00pneumatic signal that's coming from the
  324. 12:02computer
  325. 12:02that decides which of these shoots it
  326. 12:04will go down
  327. 12:06now i'm going to first of all place
  328. 12:08three caps in this area
  329. 12:10so one two three now we really only need
  330. 12:13two for this process and try to line
  331. 12:16them up in the center it'll make it less
  332. 12:18likely
  333. 12:18that the caps will jam when they're
  334. 12:20putting on
  335. 12:22another sensor that you see in this
  336. 12:23system here is an optical sensor
  337. 12:25it's an infrared beam that's shooting
  338. 12:27down to the cap
  339. 12:28reflecting back up and all that's doing
  340. 12:30is verifying that there's a cap
  341. 12:32there because you don't want to start
  342. 12:33the process without having that
  343. 12:35cap the other thing that's very
  344. 12:37important is that
  345. 12:38inside each of these little modules
  346. 12:42is a rf id and you want to put it so the
  347. 12:45rfid is sitting near the top not upside
  348. 12:48down like this
  349. 12:49and it's actually a little metal disc in
  350. 12:51the middle and i have
  351. 12:52three of them a red a black and
  352. 12:56a second red and you have to put them
  353. 12:58down this chute
  354. 13:00okay the red one first based on my
  355. 13:02programming
  356. 13:04block one second and then a red one
  357. 13:06third
  358. 13:07there's actually an optical sensor down
  359. 13:09there as well
  360. 13:10now while i'm here let me point out a
  361. 13:12few sensors
  362. 13:13all right coming around to this side we
  363. 13:15have some components that i want to look
  364. 13:17at
  365. 13:18first of all this is the holder for the
  366. 13:20parts and i have three parts in here
  367. 13:22a red a black and another red and each
  368. 13:26of those has the rfid built
  369. 13:29built in that stack the second thing is
  370. 13:31this system is able to detect
  371. 13:33whether the part is actually present
  372. 13:35because it uses something called
  373. 13:37an uh a through beam sensor so there's
  374. 13:40an emitter on this side and a detector
  375. 13:42on that side and the only way it'll be
  376. 13:44blocked
  377. 13:44is if there's an actual part in there
  378. 13:46the other thing that will happen is
  379. 13:48as the system is actuated there's
  380. 13:50actually
  381. 13:51a pneumatic cylinder here that gets
  382. 13:54extended and retracted
  383. 13:55to push the part onto the conveyor belt
  384. 13:58the conveyor belt begins
  385. 14:00and then what happens is this first
  386. 14:02device this is actually called
  387. 14:04an rf writer a radio frequency
  388. 14:07writer and the rfid sensor has a code
  389. 14:10written to it
  390. 14:11and the code tells the device do we go
  391. 14:14to
  392. 14:14international am i red in color and do i
  393. 14:17need to put a cap
  394. 14:19on the device so it has all of that
  395. 14:21information stored in the rfid
  396. 14:23and so as it moves through the conveyor
  397. 14:25belt system
  398. 14:27the second one reads it to determine
  399. 14:29whether it
  400. 14:30requires a cap or not and then the next
  401. 14:33one
  402. 14:34is verifying whether
  403. 14:38actually this one is verifying if the
  404. 14:39color is red
  405. 14:41black or translucent so all that
  406. 14:44information is bedded
  407. 14:45embedded into the rfrd okay as we move
  408. 14:48along to this center position we have
  409. 14:50this part here
  410. 14:52and a holder for our caps and actually i
  411. 14:55turned this on because of the light
  412. 14:57detection so it's holding the caps
  413. 14:59and the rfid will read whether or not a
  414. 15:02cap is required
  415. 15:04and then what happens is that there are
  416. 15:06actually two actuators here
  417. 15:08one that moves this arm in and out or
  418. 15:11horizontal actuator
  419. 15:12and one that moves this part up and down
  420. 15:15a vertical actuator as well we have
  421. 15:19a pneumatic system here that's going to
  422. 15:21pick up the part
  423. 15:23and move it back so that we put a lid
  424. 15:25onto the object
  425. 15:27but it's made up of a couple of things
  426. 15:29here it has a venturi
  427. 15:31effect device which basically is
  428. 15:33converting
  429. 15:34the compressed air to a vacuum so that
  430. 15:37we don't have to have a separate vacuum
  431. 15:39pump and that's a really great feature
  432. 15:41but the second thing that happens here
  433. 15:43you may see it when it's operating
  434. 15:45is that there's an ascent a sensor and i
  435. 15:47know that there's a sensor there because
  436. 15:48there's an
  437. 15:49electrical wire and that sensor is
  438. 15:51detecting whether or not there's a
  439. 15:53vacuum
  440. 15:54because if you try to pick up the part
  441. 15:56and you don't sense the vacuum you don't
  442. 15:58want to move it
  443. 15:58any further so once it's done that so
  444. 16:01you're going to see
  445. 16:02this actuator move across bring the
  446. 16:05vacuum
  447. 16:06suction device down to the cover back
  448. 16:08towards the part and it's being held in
  449. 16:10place because this pneumatic gate
  450. 16:12is helped holding it there and then it
  451. 16:14moves to the next stage
  452. 16:16and in the next stage it's going to read
  453. 16:19whether the part
  454. 16:20is expected to go down the national
  455. 16:22shoot international shoot
  456. 16:24or be rejected down the third shoot
  457. 16:26possibly if the color is incorrect
  458. 16:36you

About this transcript

This page contains the full transcript of Festo MPS Station Overview by M Hanbury, generated from the public captions YouTube serves with the video. The transcript has 2,645 words across 458 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.