YouTube2Text

ECM MECHANIKA MAX FIRST LOOK: ECM's Newest Release — Transcript

by Lance Hedrick · 7,224 words · 951 segments · language en · Watch on YouTube

Full transcript

  1. 0:00today we're going to check out the
  2. 0:01newest release from ECM the mechanica
  3. 0:05[Music]
  4. 0:12max so you might have seen this machine
  5. 0:14living on my bar in a lot of recent
  6. 0:16videos and it's because well I've been
  7. 0:18using it a lot over the past few months
  8. 0:20this is the new release from ECM it's a
  9. 0:23heat exchanger with their smart
  10. 0:25temperature technology and it's built
  11. 0:27like a tank a whole latte love out of
  12. 0:29the US sent me this by way of ECM so
  13. 0:32that I could try it out I enjoy loaning
  14. 0:35things from resellers as opposed to
  15. 0:37manufacturers because I feel I can be
  16. 0:39more critical when it's reseller because
  17. 0:42well they sell a lot of other stuff so
  18. 0:44doesn't to me I just it doesn't really
  19. 0:46matter um so I I feel like that gives me
  20. 0:48a little less bias but anyway this is
  21. 0:50due to whole latte love sending out to
  22. 0:52me thank you uh for letting me use this
  23. 0:55and there there's some more machines are
  24. 0:56going to be sending out my way soon so
  25. 0:58I'm excited to take a look at all as you
  26. 1:00can see I have the smart espresso
  27. 1:02profiler pressure gauge Bluetooth
  28. 1:04transducer as well as temperature uh
  29. 1:07which is in the group pad and I will
  30. 1:08also be using a scase to measure the
  31. 1:10water exiting so temperature in here
  32. 1:13temperature in here as well as the
  33. 1:14temperatures they provide in the machine
  34. 1:16itself let's get ready for a good
  35. 1:18oldfashioned Lance Deep
  36. 1:21dive I want to quickly note that what I
  37. 1:24have added here is not something that is
  38. 1:27affecting the performance of the machine
  39. 1:30so if you're looking at it going oh man
  40. 1:32I wish that he would have just taken a
  41. 1:33stock one this is stock this just tells
  42. 1:36me information that otherwise wouldn't I
  43. 1:38wouldn't be able to get this just gives
  44. 1:40me data of course we have the typical
  45. 1:42levers for the steam wand and for the
  46. 1:44hot water so you just pull up and there
  47. 1:46it goes you pull up and there it goes
  48. 1:48really nice steam power uh because well
  49. 1:50it's a heat exchanger and whenever you
  50. 1:52have it in the heat exchanger mode
  51. 1:54you're going to have the steam boiler
  52. 1:56set at whatever temperature you set it
  53. 1:58at so your pressure should be high but
  54. 2:00there are other modes that you can run
  55. 2:02this machine in and with those modes
  56. 2:04steam power is less than ideal sort of
  57. 2:06like the Lite Mara X whenever you do
  58. 2:08Brew first so that means you're
  59. 2:11concentrating on the Brew temperature
  60. 2:13first and foremost you're going to
  61. 2:14suffer a little bit on the steam
  62. 2:16temperature and that's because this is a
  63. 2:17heat exchanger machine now I have a
  64. 2:19video right here that fully breaks down
  65. 2:21what that means but essentially you have
  66. 2:23a 1.9 L steam boiler and inside you have
  67. 2:27what I call the brw tube it's a little
  68. 2:28heat exchanger tu tube inside where the
  69. 2:31Brew water is going through so it's
  70. 2:32being heated by the steam boiler inside
  71. 2:35a separate tube now what they have done
  72. 2:37with their smart temperature which is
  73. 2:39what they call it um is they have two
  74. 2:41pids inside the machine one probe is
  75. 2:44inside the steam boiler itself and you
  76. 2:46can use the PID controller on the
  77. 2:48machine up front right here in order to
  78. 2:50set the steam boiler temperature so you
  79. 2:52set the temperature and it will regulate
  80. 2:54how much the steam boiler is heating
  81. 2:57based off of the reading of the
  82. 2:58thermoprobe inside the the boiler itself
  83. 3:01they have a secondary temperature probe
  84. 3:03which is at the top within the thermos
  85. 3:05siphon Loop now if you're confused by
  86. 3:07any of these words like the thermosyphon
  87. 3:08loop I can't ask you enough to watch
  88. 3:10that video I linked earlier it shows a
  89. 3:12cutaway version of an e61 one with a
  90. 3:15heat exchanger one with a dual boiler
  91. 3:16it'll give you a much better
  92. 3:18understanding of everything but the
  93. 3:19secondary probe is inside that thermos
  94. 3:21siphon Loop giving you a little bit more
  95. 3:23accurate reading of what the temperature
  96. 3:26is of the Brew water itself now there
  97. 3:28are some downsides of that which we'll
  98. 3:29cover here in a bit but it is important
  99. 3:31to note that that is kind of what they
  100. 3:33refer to as their smart system and with
  101. 3:35that you can also you also have a PID
  102. 3:37controller so you're controlling the
  103. 3:39Therma probe that is inside that
  104. 3:41thermosyphon Loop and it will regulate
  105. 3:43the water temperature coming through
  106. 3:45that thermosyphon in order to hit what
  107. 3:47you have programmed it to if that makes
  108. 3:49sense which I hope it does regardless of
  109. 3:51the increases in the advances in
  110. 3:53technology for e61 it is still a massive
  111. 3:56hunk of Chrome plated brass and
  112. 3:58stainless steel in the front and that
  113. 4:00takes a long time to heat up with how
  114. 4:02slow a thermosyphon loop is I was
  115. 4:05getting the signal that it was ready to
  116. 4:06start brewing at around 18 minutes it
  117. 4:09took around 30 to 35 minutes before it
  118. 4:12was actually giving me the temperature
  119. 4:14of water I needed using my skas device
  120. 4:16as well as this transducer inside the
  121. 4:18e61 group itself this machine will say
  122. 4:21it is ready when it hits the Brew
  123. 4:22temperature before it actually enters
  124. 4:25this big robust piece of metal so this
  125. 4:27chunk of metal takes a lot of
  126. 4:28temperature a lot of time time to heat
  127. 4:30up sufficiently but the screen is
  128. 4:32telling you when the thermosyphon loop
  129. 4:34in the back is at sufficient heat the
  130. 4:36one that you set to out of the box it
  131. 4:37comes in the heat exchanger mode which
  132. 4:39means you set the steam boiler
  133. 4:41temperature and then it's going to heat
  134. 4:43that tube up and you need to do cooling
  135. 4:44flushes in order to get the temperature
  136. 4:46of Brew water to where you want it so
  137. 4:48what they have done is they've added a
  138. 4:50flush mode based off of that Thermo
  139. 4:52probe in the thermosyphon it tells you
  140. 4:55whether or not you need to flush to cool
  141. 4:57the water or you need to let it sit and
  142. 4:58heat up longer so it has three dashes
  143. 5:01that will be on the lower part of the
  144. 5:03screen when it's down below it means
  145. 5:05you're too low in heat you need to let
  146. 5:06it heat up until it says rdy ready if
  147. 5:09it's too hot the three dashes will be at
  148. 5:11the top of the screen and you need to
  149. 5:13flush until the timer starts which
  150. 5:15indicates
  151. 5:17[Music]
  152. 5:21ready that's when the numbers come on
  153. 5:24in hit that steam lever I read the
  154. 5:26temperature it was too cool so I put it
  155. 5:28back down and it had the three dots were
  156. 5:30too low so I let it heat up back to
  157. 5:31ready and I kept doing this process
  158. 5:34hitting it and letting it get below then
  159. 5:36getting it back to ready on and off and
  160. 5:37on and off until it hit temperature that
  161. 5:40I said which was 94 celsi so down here
  162. 5:42we have a pretty robust menu which is on
  163. 5:44that just that little screen that shows
  164. 5:46the P controller on it you can set a lot
  165. 5:49of different things which are really
  166. 5:50nice it can get a little convoluted so I
  167. 5:52recommend watching ecm's video on how to
  168. 5:55manipulate that menu which is actually
  169. 5:57done by Mark of holat love but in there
  170. 5:59you you actually have a standby mode
  171. 6:01which allows you to set two different
  172. 6:03onoff times during the weekdays and
  173. 6:05weekends for this machine so I highly
  174. 6:07recommend you either use that or a smart
  175. 6:09plug because you don't want to wake up
  176. 6:10and forget to turn this on then have to
  177. 6:12wait 35 minutes for decent temperature
  178. 6:14if you let it sit for like 2 hours or
  179. 6:16something like that without it going
  180. 6:17into eco mode this gets really really
  181. 6:20really hot on the PID controller even if
  182. 6:22it says 88 I would run it and it would
  183. 6:25say like 96 coming out regardless of the
  184. 6:28smart temperature control that they done
  185. 6:30there are still oscillations in
  186. 6:31temperature that you need to pay
  187. 6:32attention to because there's only one
  188. 6:34Thermo probe in there reading
  189. 6:35temperature that's only telling us what
  190. 6:37it's at in that one location so it's not
  191. 6:40as accurate as we might want it to be or
  192. 6:43as as maybe they thought it would be it
  193. 6:45still is more accurate than any other
  194. 6:47heat exchanger outside of the mara X and
  195. 6:49this please correct me if I'm wrong but
  196. 6:51those are the only two that I know with
  197. 6:52a more intelligent heating system now
  198. 6:55with this obviously over the mara X you
  199. 6:57actually have a PID controller where you
  200. 6:58can set a specific specific temperature
  201. 7:00but as we know that doesn't really
  202. 7:02guarantee anything so for instance if
  203. 7:04you set it to 94 what I found
  204. 7:06consistently is because you're setting
  205. 7:08it to 94 back here even if you optimize
  206. 7:11the heating up time and you have it
  207. 7:13Brewing out it hits to about 93 on this
  208. 7:15Thermo probe which goes into the group
  209. 7:17head and then on my skas device which
  210. 7:19measures water coming out it' read about
  211. 7:2190 or 91 so there's a 2 to Three Degree
  212. 7:25drop sometimes 3 and a half or so degree
  213. 7:27drop from that that back here to up here
  214. 7:30to where the water's actually escaping
  215. 7:32so keep that in mind if they do have an
  216. 7:34offset option in your menu if you do
  217. 7:36have a thermo probe that you're able to
  218. 7:38measure water coming out or if you just
  219. 7:40want to guess that there will be a 3°
  220. 7:41offset and you want to know that coming
  221. 7:43out is identical to what you're setting
  222. 7:45then you can use that offset feature or
  223. 7:47if you have ambient temperature issues
  224. 7:49wherever you're at then it can also mess
  225. 7:51with your temperature so you're going to
  226. 7:53want to set the
  227. 7:56offset now as you'd expect from ECM they
  228. 7:59do have a stainless steel chassis they
  229. 8:01have an incredible build quality and
  230. 8:03again we'll we'll take off the Hood in a
  231. 8:04second look inside they do a great job
  232. 8:06with using the highest quality
  233. 8:08components all very easy to change out
  234. 8:10they have a very weighted Porta filter
  235. 8:12two of them that come with the machine I
  236. 8:14wish it came with one naked and one
  237. 8:15split shot but it comes with one single
  238. 8:17spout and one double spout uh they have
  239. 8:19these Chrome plated ends which make it
  240. 8:21all look really nice obviously the whole
  241. 8:23machine itself is has this mirror finish
  242. 8:26uh which is beautiful it does get really
  243. 8:27annoying to clean because of course your
  244. 8:29fingers get on it you get espresso kind
  245. 8:31of flying in places with channels you
  246. 8:33get um you know if you're purging the
  247. 8:35steam wand or whatever you get steam
  248. 8:37kind of building up when you go to clean
  249. 8:39it it can get streaky yada y yada but
  250. 8:40we're used to that with e 61s right they
  251. 8:42tend to be this chrome you know mirror
  252. 8:44finish type of things there is a
  253. 8:46pre-infusion setting inside when I first
  254. 8:48heard about this I was really excited
  255. 8:50because I thought it meant it would cap
  256. 8:52your pressure at something like three or
  257. 8:53four bar and and it does but only if you
  258. 8:55Plum the machine in that means there are
  259. 8:57two modes of pre-infusion on this Ma
  260. 8:59machine passive and active so with the
  261. 9:02passive pre-infusion you must have it
  262. 9:03plumbed in and with that you're getting
  263. 9:05whatever the pressure is of the line
  264. 9:07feeding into the machine and then it
  265. 9:10will have a certain amount of time of
  266. 9:11passive pre-infusion and then it will
  267. 9:13immediately go into your full infusion I
  268. 9:16actually prefer the term saturation and
  269. 9:17extraction whatever you want to call it
  270. 9:19pre-infusion doesn't really mean much
  271. 9:21but anyway that's beside the point I
  272. 9:22digress you will get that 3 to four bar
  273. 9:24Max during the saturation phase and then
  274. 9:27it'll ramp up to around eight bar in the
  275. 9:29actual group head um it's set to nine
  276. 9:32bar at The Rotary pump but it only it
  277. 9:33gets up to nine bar and then it Flats at
  278. 9:35around 8 8.1 bar during the actual
  279. 9:38extraction whenever you're going from
  280. 9:39the water tank though uh which this
  281. 9:41makes sense I was just hoping they
  282. 9:43figured out a way to have like maybe a
  283. 9:45couple of solenoids that there's only
  284. 9:46one solenoid in this whole thing which
  285. 9:48is a little unusual maybe if there's a
  286. 9:49way they could have different flows or
  287. 9:51you know maybe some sort of variable um
  288. 9:54I I I don't even know what I was
  289. 9:56thinking but I was hoping there was a
  290. 9:57way they could cut it off at three or
  291. 9:58four are for the early pre-infusion
  292. 10:00before it ramped up to 9: but all that
  293. 10:03it's doing when you're going from a
  294. 10:04water tank is it is the same thing as
  295. 10:07turning on your pump turning off the
  296. 10:09pump then turning it back on so what you
  297. 10:11do is you set active pre-infusion for 8
  298. 10:14seconds and what that will do is it will
  299. 10:16go full blast the pump is on running
  300. 10:18full blast and you'll ramp up to nine
  301. 10:20bar and at the end of whatever time that
  302. 10:22you program from zero to like 9 or 10
  303. 10:24seconds however long you have that set
  304. 10:26for active pre-infusion it will go it
  305. 10:29will go all the way up to 9 bar and it
  306. 10:30will stay there until your time is up
  307. 10:32that you have pre-programmed and then
  308. 10:34what you can do is you can then program
  309. 10:37passive pre-infusion you have to do this
  310. 10:39now what this is whenever it's just a
  311. 10:41water tank is it will just turn the pump
  312. 10:43off that's all it's going to do and
  313. 10:45since there's not enough pressure from
  314. 10:46just the steam built up inside the
  315. 10:48boiler it just essentially tapers off to
  316. 10:51nothing all right so essentially you
  317. 10:52turn the pump on with active
  318. 10:54pre-infusion then passive pre-infusion
  319. 10:56it just turns the pump off so all the
  320. 10:57water essentially stops being being fed
  321. 10:59except for what's left over from the
  322. 11:01pressure being pushed you don't release
  323. 11:03the valve when you do this so whatever
  324. 11:05leftover pressure is there as it
  325. 11:06dissipates is going to continue to
  326. 11:08infuse and then once your time of
  327. 11:10passive pre-infusion is up it will go to
  328. 11:12full nine bar yet again so so I was a
  329. 11:15little disappointed about this because
  330. 11:17you you do have time restrictions and
  331. 11:20you're better off just using the lever
  332. 11:22to do the same exact thing if you go all
  333. 11:24the way up with the lever like so you
  334. 11:27can go down not all the way down cuz
  335. 11:30going all the way down will'll release
  336. 11:31the valve right and then you'll unseat
  337. 11:33the puck so instead of faffing around
  338. 11:34with the menu and guessing you can
  339. 11:37actually do this and watch when the
  340. 11:39liquid will come out and then if you
  341. 11:40need 4 seconds as opposed to 6 seconds
  342. 11:42then you can do that you can sit here
  343. 11:44and let it sit off as long as you want
  344. 11:46then reactivate the pump and it's going
  345. 11:47to give you the same exact effect as
  346. 11:50what is going on in the menu whenever
  347. 11:52it's from the water tank obviously if
  348. 11:54you have it plumbed in you can use line
  349. 11:55pressure and have something completely
  350. 11:57different that's not obtainable with the
  351. 11:59machine coming from water tank I like
  352. 12:01going from the tank because I don't have
  353. 12:03a full filtration system at home and I
  354. 12:05refuse to put tap water into my machine
  355. 12:07and I also don't want to mess around
  356. 12:08with a 5 gallon bucket or one of those
  357. 12:10massive buckets and making my own water
  358. 12:12I like to just do it tank by Tank anyway
  359. 12:14let's go ahead and pull some shots and
  360. 12:16I'll show you the graphs on the screen
  361. 12:17so you can kind of see what I mean by
  362. 12:19all of this so instead of actually using
  363. 12:21the programmed pre-infusion which I
  364. 12:23promise is the same thing I'm just going
  365. 12:26to pull you a manual shot and show you
  366. 12:27that you can go fully open you can turn
  367. 12:29off the pump without releasing a valve
  368. 12:31just like a normal e61 and then
  369. 12:33reintegrate it and then at the end you
  370. 12:35can taper off the pressure by turning
  371. 12:36the pump off again before shutting it
  372. 12:38down and you'll also be able to see the
  373. 12:40temperature on this once it's done and
  374. 12:42you'll be able to get an idea of what
  375. 12:43the temperature probe here is reading
  376. 12:45which is the entering water into the
  377. 12:47group granted it might lose another half
  378. 12:49degree or degree before it actually hits
  379. 12:50the puck but you'll get a pretty good
  380. 12:52idea all right so let's get this set
  381. 12:54[Music]
  382. 12:57up now real quick before I pull this
  383. 12:59there are three Brew temperature modes
  384. 13:01as I said it comes in the heat exchanger
  385. 13:03mode which is just based off the steam
  386. 13:05boiler and you'll have to flush it in
  387. 13:06order to get uh that cooling flesh to
  388. 13:08get to the right temperature and it can
  389. 13:10give you a guidance for that then there
  390. 13:12are three Brew temperature modes the
  391. 13:14first one is a slow heat up which will
  392. 13:17have a low overshoot meaning let's say
  393. 13:19it's set at 94 it'll slowly heat up the
  394. 13:21steam boiler so that the P ID inside of
  395. 13:24the thermosyphon is going up like 90
  396. 13:2790.5 9 91 92 whatever and then it will
  397. 13:32barely overshoot it before it equalizes
  398. 13:34and hits where you need it bt2 is faster
  399. 13:37and but and it will overshoot a little
  400. 13:39bit more because of the speed it's
  401. 13:40heating up the steam boiler bt3 are for
  402. 13:42more experienced people that you know
  403. 13:44have an understanding of v61 it'll heat
  404. 13:46up the fastest but it'll also have the
  405. 13:48biggest overshoot so you have to keep
  406. 13:50that in mind but they are Brew
  407. 13:52temperature forward so what this means
  408. 13:54is the pressure of the steam boiler
  409. 13:56won't really be at a pressure that you
  410. 13:58need to steam milk so what you can do is
  411. 14:00during your shot when you're in one of
  412. 14:02these Brew temperature control modes is
  413. 14:03you can hit the down button and it will
  414. 14:06activate the steam boiler to go to the
  415. 14:08temperature you have already set the
  416. 14:10steam boiler at while you're pulling the
  417. 14:11shot not ideal because I guess it could
  418. 14:14increase the temperature of your Brew
  419. 14:16but really the thermosyphon is so slow
  420. 14:18that it shouldn't uh but it is I guess a
  421. 14:20fear if you double click the down button
  422. 14:22the down arrow what will happen during
  423. 14:24your Brew is the steam boiler will be
  424. 14:26turned on to full gear and what will
  425. 14:28happen is unless you turn it off by
  426. 14:29clicking the button again it will
  427. 14:31continue heating for 3 minutes and then
  428. 14:33turn off automatically so if you're
  429. 14:34doing Brew temperature mode first and
  430. 14:36foremost you can get that steam back on
  431. 14:40but I feel like most people doing The
  432. 14:41Brew temperature mode are drinking
  433. 14:42espressos first and foremost otherwise
  434. 14:44you'd be in heat exchange mode because
  435. 14:46the espresso the temperature doesn't
  436. 14:47matter nearly as much okay my P
  437. 14:50controller shows it's at 95 so just a
  438. 14:52degree over where it should be set but
  439. 14:54you'll see what's actually coming out
  440. 14:56here we go so I'm going to start this
  441. 14:59we're going to we're going to go once it
  442. 15:01reaches
  443. 15:02pressure there we go it's at nine I'm
  444. 15:04going to cut off the pump but I have not
  445. 15:08released the valve so I'm letting this
  446. 15:10go for a few seconds we're at about 7 G
  447. 15:13I'm going to turn the pump back on so it
  448. 15:15didn't unseat the pump we're good to go
  449. 15:16I've turned it back on this is a light
  450. 15:18roasted coffee so it's not going to look
  451. 15:19all velvety and thick and whatever you
  452. 15:21might want to think uh this is a very
  453. 15:23lightly roasted Kenya coffee so it's not
  454. 15:26going to be as pretty then I turn the
  455. 15:28pump back off for a little bit and then
  456. 15:30once it hits 60 G cuz I'm doing a one to
  457. 15:32three shot we pull it all right so what
  458. 15:37we have here as you can you saw the shot
  459. 15:38in real time I going to now pull up the
  460. 15:41temperature of that one and so if you
  461. 15:44look it said it was 95 in that
  462. 15:47thermosyphon Loop okay it said 95 but
  463. 15:50because we've been sitting here filming
  464. 15:51and I've not flushed I'm not really done
  465. 15:53anything look at the temperature it
  466. 15:55starts at 99 it goes up to 101 1015 goes
  467. 15:59down 99 5 998 97 96 95 986 it jumps up
  468. 16:04once I turn the pump back on so as you
  469. 16:06saw that's when I turned the pump off
  470. 16:08the temperature started to go down when
  471. 16:09I turned the pump back on it went back
  472. 16:11up to 987 983 979 and then at the end it
  473. 16:16shot down when I turned the pump back
  474. 16:17off so that will give you an idea of
  475. 16:20what it looks like over 35 seconds so
  476. 16:22even when this P controller at the top
  477. 16:25tells you the temperature it doesn't
  478. 16:27mean it's accurate in the group head I
  479. 16:29can't stress that enough that you still
  480. 16:32because it's an e61 group head you still
  481. 16:34have
  482. 16:35some unpredictability it's it's there's
  483. 16:38no such thing as a perfect e61 there's
  484. 16:40no control once it gets here and that's
  485. 16:43the big flaw the inherent flaw on e61
  486. 16:46you will never truly know even if you
  487. 16:48have a thermopro here which I know a lot
  488. 16:50of you do this is not an exact
  489. 16:51representation of what comes out of here
  490. 16:53there are times I'll have a 4 Dee gap
  491. 16:56between water that's here and the water
  492. 16:57coming out of here with my SK device
  493. 16:59Gregory SK in 2006 or 2007 made this
  494. 17:02device which is like there's something
  495. 17:05here to replicate a puck and how it
  496. 17:06absorbs heat you have a thermo probe
  497. 17:08there and then it allows a 2 mm aperture
  498. 17:11I believe it is so that it builds up to
  499. 17:13nine bar of pressure inside the puck
  500. 17:15head or whatever the opv is set at so it
  501. 17:17forces it out at a similar rate to the
  502. 17:19exit flow of a puck granted it doesn't
  503. 17:21disintegrate fluctuations that will
  504. 17:23occur because of the quickening outward
  505. 17:25flow rate of espresso due to the
  506. 17:27degrading of the puug I plug this into
  507. 17:29my very expensive fluke thermometer and
  508. 17:33I'm able to get temperatures inside the
  509. 17:35group head or inside the puck itself and
  510. 17:37there are times depending on the heat up
  511. 17:39of the machine where this probe does not
  512. 17:42accurately tell me what's coming out now
  513. 17:45if I run it for a long time like I let
  514. 17:46it sit there and run over time they do
  515. 17:48almost equalize but this is still always
  516. 17:50about half a degree to a full degree off
  517. 17:52to what's coming out so to those of you
  518. 17:54at home that are using a thermo probe
  519. 17:56placed inside the group head itself just
  520. 17:58know that that is not what that's not
  521. 18:00reflective fully of what's coming out of
  522. 18:02here sometimes it's within half a half a
  523. 18:04degree centigrade to a degree but there
  524. 18:06are a lot of times it's 3 4° off so this
  525. 18:10this Thermo probe inside the machine
  526. 18:11itself in the thermosyphon loop not very
  527. 18:14reliable for what's actually coming out
  528. 18:16this one much more reliable but still
  529. 18:18not quite there butthole let go now even
  530. 18:23though the Brew temp was too hot this
  531. 18:25was a lightly roasted Kenya I'm I'm
  532. 18:27curious what it tastes like but we'll
  533. 18:28try pulling it again I'm going to do a
  534. 18:29big flush before see if we can get that
  535. 18:31temperature down uh but yes this is in
  536. 18:34brw temperature one so it should have
  537. 18:36the lowest overshoot obviously there was
  538. 18:39a big overshoot even though I'm in
  539. 18:45bt1 it's pretty good it's a little acrid
  540. 18:47which I think will go away if we
  541. 18:49actually hit 94° so let's do another one
  542. 18:52I'm going to flush a little bit more I
  543. 18:53want this top one to go down just a bit
  544. 18:56more supposed to be at 94
  545. 18:5997 959 947 there we go now we're dipping
  546. 19:03all right so I've purged it to where
  547. 19:04we're getting roughly 94 out up here
  548. 19:07which means that we're at night 93 in
  549. 19:09this Cas so anyway let's go ahead give
  550. 19:11this a try we're going to lock it in
  551. 19:13now so I'm going to do the pre-infusion
  552. 19:15again I'm going to let it go till I see
  553. 19:17a couple drops and we'll turn the pump
  554. 19:19off there we go pump's off I don't want
  555. 19:21to touch that cuz it'll mess with the
  556. 19:23scale reading here but we might get a
  557. 19:25little messy all right so we're going to
  558. 19:28do that till about 7 G we're back
  559. 19:32on so there we go here it comes uh-oh
  560. 19:35we're getting a little mess but if I
  561. 19:37move it it will mess up the reading on
  562. 19:39here so I'm just going to let it get
  563. 19:40messy it's fine it's fine now we're at
  564. 19:4542 right here I'm going to go pump off
  565. 19:47and let it just kind of use the excess
  566. 19:49pressure and then boom we cut that valve
  567. 19:52and there we go we're going to take a
  568. 19:54look now at temperature so it took a lot
  569. 19:56of flushing but we hit it was sitting at
  570. 19:59at the beginning it was at 955 then I
  571. 20:01cut off the pump and it shot down to
  572. 20:03about 92 and then when I turned the pump
  573. 20:06back on it went up to 939 94 94 941 and
  574. 20:09there you go so that time it was at a
  575. 20:12really nice temperature as you can see
  576. 20:15it can do a good job it just does
  577. 20:16overheat even when you have the small
  578. 20:18overshoot programmed in even with the
  579. 20:20brw temperature first but you if you
  580. 20:23flush flush flush flush you should be
  581. 20:25good to go now this will help as you saw
  582. 20:27it was reading 100 but this needs to get
  583. 20:29down to like 95 94 93 before you start
  584. 20:33pulling the shot so I highly recommend
  585. 20:35regardless of what you have whether it's
  586. 20:36the Lite Mara X or this machine even
  587. 20:39with the smart heat exchangers you still
  588. 20:41need the thermo probe here they're not
  589. 20:42very expensive all you have to do is
  590. 20:44pull this little screw out you don't
  591. 20:46even need to get the pressure gauge this
  592. 20:47one is a more expensive TR transducer
  593. 20:50but if you want you can buy like a y
  594. 20:52splitter and get something like um the
  595. 20:54temperature probe and a pressure gauge
  596. 20:56throw it in there all you got to do is
  597. 20:57take out this little screw with an with
  598. 20:59an allen wrench well let me take a sip
  599. 21:00of this actually I'm curious now that
  600. 21:02it's pulled like 6° cooler what it's
  601. 21:05going to taste
  602. 21:10like much much much better that acrid
  603. 21:13nonsense is gone and here comes Ugo to
  604. 21:15steal a sip M much better
  605. 21:19right finally oh my God all right so
  606. 21:22next up I'm going to turn this off let
  607. 21:23it cool down just a bit and we'll open
  608. 21:25it up look at the insides before we kind
  609. 21:26of wrap up here at the end so that's do
  610. 21:29ready ready ready ready
  611. 21:33ready yes nice after about 47 minutes
  612. 21:36and
  613. 21:3714376 screws as well as difficult to
  614. 21:40reach places we now have the back panel
  615. 21:42off so let's take a look at what's going
  616. 21:44on inside here and how it differs from
  617. 21:46some of the others so first of all of
  618. 21:48course we see this is where the water
  619. 21:50intake is whether you're plumbed in or
  620. 21:52whether you have the water tank now what
  621. 21:54is really great is right
  622. 21:57here we have a rotary pump now this is a
  623. 22:00beefy boy um the larx for instance has
  624. 22:03one of the silent vibratory pumps this
  625. 22:05bad boy releases a water debit if you
  626. 22:08just open that lever up it comes out at
  627. 22:11around 13 mlit a second that is super
  628. 22:15heavy water debit and what I actually
  629. 22:17like it that high I'm I'm a fan I'm a
  630. 22:19fan for sure the Lite for instance comes
  631. 22:21out at like five five a half g a second
  632. 22:23the Lily Bianca comes out at like seven
  633. 22:25six or seven gam a second U this one's
  634. 22:27coming out at a dring 13 or so now what
  635. 22:31are the implications for that with flow
  636. 22:32control well you'll have you'll
  637. 22:34definitely have more uh of um of a range
  638. 22:38but you won't be able to open it up all
  639. 22:39the way to 13 if you're wanting to close
  640. 22:41it off all the way as well so you're
  641. 22:43still going to have a shorter range on
  642. 22:44flow control you're going to have to
  643. 22:45give up some of that upper end but if
  644. 22:47you're only using the lever or the
  645. 22:49pre-infusion I mean 13 is that's that's
  646. 22:51a that that pelts the puck um so I do
  647. 22:55recommend using a puck screen for that
  648. 22:56but and what's really neat is right here
  649. 22:58actually you can see that you can take
  650. 22:59off the head and you can actually
  651. 23:01rebuild some of that pump If Ever Needed
  652. 23:03hopefully this won't ever need it but
  653. 23:05you know you never know so it's nice to
  654. 23:06know that at least that is an option
  655. 23:08with this uh with this beasty boy not
  656. 23:11only is this a really difficult machine
  657. 23:12to open up but instead of taking the
  658. 23:15side panel off and having direct access
  659. 23:17to the solenoid what you have direct
  660. 23:19access to is the the wire control so you
  661. 23:21have it all housed right here see if you
  662. 23:23have any issues with electronics sure
  663. 23:25that's easy to get to but the solenoid
  664. 23:27is stuck right back in here okay so you
  665. 23:30have to take off the full you have to
  666. 23:31take off this side panel take off the
  667. 23:33electric box in order to reach the
  668. 23:35solenoid which is housed down there and
  669. 23:37and again there's only one on this which
  670. 23:40is interesting uh but it can also I
  671. 23:42guess that's one less to to have to
  672. 23:44clean up if it ever gets jammed or
  673. 23:46anything um which it shouldn't again
  674. 23:48these are using high quality parts that
  675. 23:50should be completely fine now as you see
  676. 23:52everything else looks pretty standard we
  677. 23:54have um right here we have the the
  678. 23:57thermo probe for the for the steam
  679. 23:59boiler so this is temperature two which
  680. 24:01is how you set on the the front screen
  681. 24:04that's how you set the steam boiler
  682. 24:05temperature so we have that temperature
  683. 24:07probe here we have the other temperature
  684. 24:10probe here which this is part of the
  685. 24:12thermosyphon unit so this is the intake
  686. 24:15into the group head itself and down
  687. 24:17below where you can't see is the what it
  688. 24:18comes out of the bottom of the e61 group
  689. 24:21head but this is where it's taking the
  690. 24:23temperature is right there all right
  691. 24:25this is the steam boiler pressure gauge
  692. 24:27so you can follow this coiled wire over
  693. 24:29to here so it's taking the pressure
  694. 24:32right there so it's releasing it and
  695. 24:33allowing us to read the steam boiler
  696. 24:35pressure so obviously if we're in Brew
  697. 24:37control mode we're going to have maybe
  698. 24:38around one bar of pressure on the steam
  699. 24:40wand of course to steam really nice
  700. 24:42texture you want it to be around 1.2 or
  701. 24:44higher 1.5 will make it the easiest
  702. 24:47which is where it would live in the heat
  703. 24:48exchanger mode that the the machine
  704. 24:50comes default in then of course over
  705. 24:52here we have the pump pressure so you
  706. 24:54can fold this line it drops down here it
  707. 24:58comes all the way down to the back of
  708. 25:00the rotary vein pump so it just goes up
  709. 25:02to 9ine that's not showing back pressure
  710. 25:04it's showing pump pressure so make sure
  711. 25:06you know the difference there pump
  712. 25:08pressure is reading directly from the
  713. 25:09pump so it takes water into the pump and
  714. 25:12it's coming out at nine bar but of
  715. 25:13course it loses pressure and everything
  716. 25:15going through the whole system because
  717. 25:16then it's dictated by pressure coming
  718. 25:18out of the boiler right instead of
  719. 25:21having the back pressure here what we
  720. 25:23have is the pump pressure if you want to
  721. 25:26have Puck pressure or back pressure
  722. 25:28pressure you'll need to install in that
  723. 25:30hole that I have installed the Y
  724. 25:31splitter you'll need to install a
  725. 25:32pressure gauge or a y splitter for
  726. 25:34pressure gauge in thermoprobe or
  727. 25:35something like that otherwise all you're
  728. 25:37ever going to see is the pump pressure
  729. 25:40which doesn't tell you what it is at the
  730. 25:41puck all right it'll say it'll say nine
  731. 25:44bar P pump pressure even if you're you
  732. 25:46know at one bar because you went way too
  733. 25:48coarse so you're oh I'm at nine bar but
  734. 25:50really you're at like one bar back
  735. 25:52pressure so just because the pump is
  736. 25:54feeding nine bar doesn't mean that the
  737. 25:55puck is experiencing nine and as we saw
  738. 25:57earlier the pumps says nine but of
  739. 25:59course coming at the group is about
  740. 26:00eight bar here is the steam wand this is
  741. 26:02where the steam is released into right
  742. 26:05here so as you see it goes to the valve
  743. 26:07and then all there is is a ball valve
  744. 26:08there you pull down the lever it opens
  745. 26:10up a spring that opens ball valve and
  746. 26:11boom you got steam straight from the
  747. 26:13boiler over here you have the hot water
  748. 26:15which is Al is taken out of the bottom
  749. 26:17right down here I'm not a big fan of
  750. 26:19just how difficult it is to kind of take
  751. 26:21everything apart of course it's not that
  752. 26:23it's difficult it's just time consuming
  753. 26:26nothing you shouldn't be unused to if
  754. 26:27you're taking down an e61 if you ever
  755. 26:30want to drain the whole thing you've got
  756. 26:31to flip it upside down with the mushroom
  757. 26:33cap off to let it all drain out but all
  758. 26:35the parts are really nice it has this
  759. 26:36nice jacket around the stainless steel
  760. 26:38boiler we have this new trend where you
  761. 26:40have everything feeds into that bottom
  762. 26:43release in the drip tray which is that
  763. 26:45little nut underneath the e61 group head
  764. 26:47if any leaks do occur within the opv or
  765. 26:49within uh the steam boiler itself or
  766. 26:51anywhere else all of that releases into
  767. 26:54this one tube that will just drip out in
  768. 26:56the in the in the drip tray the water
  769. 26:57tank doesn't actually come with a lid
  770. 27:00like a specific lid which I'm not a fan
  771. 27:02[Music]
  772. 27:05of so whenever you put this on top you
  773. 27:08can get dust particles coffee grounds
  774. 27:09whatever that might be flying around
  775. 27:11into your water tank since there's not a
  776. 27:13dedicated lid like there is on like
  777. 27:15every other machine and so I'm not a fan
  778. 27:17of that in fact I unintentionally didn't
  779. 27:19use this for about 2 weeks and when I
  780. 27:21came back there was a lot of floaters in
  781. 27:23here because things had fit underneath
  782. 27:25this grate and into the water tank that
  783. 27:27being said the water tank is 3 l which
  784. 27:29is a pretty good size uh and considering
  785. 27:32that the steam boiler itself is 1.9 L
  786. 27:34you have a lot that you can do and in
  787. 27:36one go essentially this or the mara X
  788. 27:38they both have the smart control Smart
  789. 27:40temperature control system they both
  790. 27:41obviously have their flaws because of
  791. 27:43the nature of e61 group heads what
  792. 27:45should I go for well obviously this one
  793. 27:47is quite a bit more expensive I'm not
  794. 27:49going to say prices here because it
  795. 27:50varies so vastly around the world it's
  796. 27:53like at least with the Lite there are
  797. 27:55loads more expensive in the US than they
  798. 27:57are Europe like almost double price it's
  799. 28:00kind of crazy with ecms I don't think
  800. 28:02the price jump is as high but it's still
  801. 28:04these are a lot more expensive than the
  802. 28:05Lites um and that can be because of
  803. 28:08maybe some of the the cost of the parts
  804. 28:09used um but you know beyond that it's
  805. 28:12all down to kind of conjecture whether
  806. 28:14or not these parts will last longer than
  807. 28:16something in an elite I mean regardless
  808. 28:18you have things that are off the shelf
  809. 28:20easy to maintain easy to fix uh but in
  810. 28:22in in all reality whether you get the
  811. 28:25Lite or this one if you're taking care
  812. 28:26of it well it's going to they're going
  813. 28:28going to last a long long long time
  814. 28:30because of how well built both of them
  815. 28:32are because of the repairability of the
  816. 28:34items and because how easy e61 are to
  817. 28:36service now the downsides of both
  818. 28:38obviously is the massively long heat up
  819. 28:40time you just have that big hunk of of
  820. 28:42brass on front it's going to take
  821. 28:43forever to heat up it's not very energy
  822. 28:45efficient is what I'm trying to say
  823. 28:46neither one of them are now this one
  824. 28:48does have the rotary pump which is a
  825. 28:49plus and it does have PID controllers on
  826. 28:51the steam boiler and on the Brew boiler
  827. 28:54so you can set specific degrees uh
  828. 28:56within a within a smallish range
  829. 28:58whereas on the Marx you have three
  830. 29:00temperature settings that kind of range
  831. 29:02like 9091 you have like 9394 like 9697
  832. 29:06so you don't really have as much
  833. 29:08granular control on temperature but as
  834. 29:09we've seen you're not really getting
  835. 29:12granular control anyway because of all
  836. 29:15the systems that it loses heat to as it
  837. 29:17goes to the group head so I don't know
  838. 29:19if I would say it's a huge benefit to
  839. 29:22have PID control on this as far as
  840. 29:24granular temperature control because
  841. 29:27it's it's taking temperature from here
  842. 29:29in the thermosyphon so I don't know how
  843. 29:32how how much better that really is like
  844. 29:35maybe a manuia of us that are tasting
  845. 29:38very very lightly roasted coffees and
  846. 29:40need specific temperatures maybe but in
  847. 29:43all reality because of the
  848. 29:45unpredictability of these and the fact
  849. 29:47that the temperature reading will be
  850. 29:48different from here to the actual in in
  851. 29:51the one the thermoprobe I have in the
  852. 29:53group head versus what's actually coming
  853. 29:55out with my SK the fact that they're all
  854. 29:57kind of
  855. 29:58unpredictable like I said there are
  856. 30:00times this one back in the back the one
  857. 30:02in the thermosiphon would read 85 after
  858. 30:04a shot it would read 85 and that's true
  859. 30:07because it was pulling in fresher water
  860. 30:08but because the thermosyphon works so
  861. 30:10slowly when I pulled a shot on the SK
  862. 30:12even though this one readed 85 the ske
  863. 30:14would be 96 an 11 degree jump so there's
  864. 30:17really no way to truly predict this this
  865. 30:20because of all the areas where heat can
  866. 30:22be lost or maintained so in the end when
  867. 30:26you're buying one of these you have to
  868. 30:27know it's kind of a trp shoot you need
  869. 30:28to optimize your ability to really track
  870. 30:32temperature by using a thermoprobe or
  871. 30:34get it to that to its hottest setting
  872. 30:36early and pull your shots and turn it
  873. 30:38off you want to use it right after about
  874. 30:4130 minutes between that 30 minute and an
  875. 30:42hour once it's past an hours when it
  876. 30:44starts to get a little volatile in its
  877. 30:46temperature fluctuations regardless of
  878. 30:48the Brew control setting it is on even
  879. 30:50on the lowest one that should have the
  880. 30:51smallest overshoot we still saw
  881. 30:53temperatures over 100 in that shot we
  882. 30:55showed earlier in the video If you're
  883. 30:57looking for a heat exchanger and you
  884. 30:59want that rotary pump I mean I don't
  885. 31:01know what else to really recommend but
  886. 31:02when it comes down between this and the
  887. 31:04mara X you're looking at the biggest
  888. 31:06differences are obviously vibratory pump
  889. 31:07versus rotary pump a big difference is
  890. 31:10some of the some of the build quality on
  891. 31:11this might be a little a little better
  892. 31:13than that on the Lite but whether or not
  893. 31:15that'll affect you as a home user I
  894. 31:17don't think longevity those parts are
  895. 31:18going to be that different to be honest
  896. 31:19with you and if they are well they're
  897. 31:21off the shelf uh the other big thing is
  898. 31:23the water debit due to the pumps this
  899. 31:25one being rotary has that 13 mli a
  900. 31:28second water debbit so if you want to
  901. 31:29fill your Puck by turning the pump on
  902. 31:31then cut it off for a blooming phase
  903. 31:33where it just tapers off uh without
  904. 31:35unseating the puck well you're going to
  905. 31:36be able to fill a lot more quickly and a
  906. 31:38lot more evenly on this whereas on the
  907. 31:40Lite it's about 5 Ms a second much much
  908. 31:42much slower due to that um olab silent
  909. 31:46vibratory pump um as far as the thermal
  910. 31:48stability they're both about honestly
  911. 31:50they're both about equal this one you do
  912. 31:52have again you have that granular
  913. 31:54control but whether or not that actually
  914. 31:55makes a big difference because of the
  915. 31:57way that you have to optimize the
  916. 31:58machine during your Puck prep and all
  917. 32:00these different things who knows if it
  918. 32:02actually is worth it but in the end um
  919. 32:05it's a great machine and it's one that
  920. 32:07if you buy you're not going to regret
  921. 32:08buying uh the question is you know do
  922. 32:10you want a little bit more expensive or
  923. 32:12do you want with a rotary vein pump and
  924. 32:14the higher water debit or do you want a
  925. 32:15little less expensive uh with with the
  926. 32:17Marx that's up to you I I give them both
  927. 32:20my stamps of approval I love EC them and
  928. 32:22their build quality I love the machine I
  929. 32:24think it does a great job once you get a
  930. 32:25handle of the thermal kind of the
  931. 32:28properties of it same with the the mara
  932. 32:30X so if you're into e61 you want heat
  933. 32:33exchanger for that constant flow of
  934. 32:34fresh water these are great options so
  935. 32:37that's about it that's everything you I
  936. 32:39hope that you need to know about this
  937. 32:40again I recommend looking at the uh ECM
  938. 32:43channel for the rest of it I want to
  939. 32:44thank H lat love again for forwarding
  940. 32:46this machine over to me if you're in the
  941. 32:48US definitely go check them out for
  942. 32:50pricing and they do a great job
  943. 32:52servicing the machines helping you out
  944. 32:53with that um yeah so thank you H love uh
  945. 32:57thank you all for watching this again if
  946. 32:58you have not hit that like And subscribe
  947. 33:00I um I would really appreciate that it
  948. 33:02really helps the channel grow and uh
  949. 33:04yeah I think that's it I hope that uh
  950. 33:06you brew something tasty today and
  951. 33:08cheers

About this transcript

This page contains the full transcript of ECM MECHANIKA MAX FIRST LOOK: ECM's Newest Release by Lance Hedrick, generated from the public captions YouTube serves with the video. The transcript has 7,224 words across 951 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.