YouTube2Text

DIY Window Tint for Tesla Model 3 (Gen1 & Highland) by TWRAPS — Transcript

by TWRAPS · 1,042 words · 146 segments · language en · Watch on YouTube

Full transcript

  1. 0:04hey folks this video with TS and today
  2. 0:07I'll show you how to save hundreds of
  3. 0:08Dos on professional tinting by doing a
  4. 0:11doityourself window tint uh on the Tesla
  5. 0:14Model 3 now we have the highlength here
  6. 0:17but it's the same uh on the previous
  7. 0:20generation model 3 uh the differences
  8. 0:22are tiny and it's the same principle on
  9. 0:25the model y as well so before we
  10. 0:28begin uh let me just speak a little bit
  11. 0:31about what you're getting other than the
  12. 0:32th cutouts that are cut to fit perfectly
  13. 0:35and be easy to install uh you're also
  14. 0:38getting a rubber squeegee and a plastic
  15. 0:40one and you will need your own spray
  16. 0:43bottle that you want to fill up uh with
  17. 0:46the liquid soap and water I mix them in
  18. 0:48about 11 15 ratio uh but you basically
  19. 0:51need this to be really soapy for this to
  20. 0:54work easily now the first step of the
  21. 0:57installation will be to pop the window
  22. 0:59open
  23. 1:00which I'll do using the plastic squeegee
  24. 1:02uh you basically want to move this hinge
  25. 1:06here so the window pops open and be very
  26. 1:10careful to not close the door once the
  27. 1:12window is open because if you close it
  28. 1:14it may break it will uh scratch the
  29. 1:17stream here so just be careful about
  30. 1:20that now the next step would be to use
  31. 1:23my soapy
  32. 1:24solution to clean this
  33. 1:33and if you want if you want to uh avoid
  34. 1:36getting this wet although nothing
  35. 1:38happens if you get it wet you can put a
  36. 1:40trash bag uh a plastic trash bag here uh
  37. 1:43you can hold it with paper tape it works
  38. 1:47great but
  39. 1:49again it's not much water nothing really
  40. 1:53happens you can just wipe it after up to
  41. 1:55you now that this is clean uh I will
  42. 1:59spray my tint I put it on the on the
  43. 2:01trunk I'll spray the tint on top I'll
  44. 2:04lift it up spray the adhesive side and
  45. 2:06then I'll transfer it
  46. 2:09here and notice that there will be the
  47. 2:11letters P and D indicating passenger and
  48. 2:14Driver
  49. 2:22sides just before I put the tint I'll
  50. 2:24spray again
  51. 2:31and
  52. 2:32then let's apply the
  53. 2:39tin now I'll use my plastic squidy to C
  54. 2:43it in
  55. 2:44here and run your finger on top you
  56. 2:46don't want to be picking on the T so if
  57. 2:49you are somewhere like here you want to
  58. 2:52lower it a little
  59. 2:54bit if you do end up posting Style with
  60. 2:58the tint
  61. 3:01showing uh past the edge you can use a
  62. 3:04utility knife run back to knife just run
  63. 3:07it to the edge to trim it pretty easy
  64. 3:11but if you position it properly now you
  65. 3:14generally don't need this because as you
  66. 3:17can
  67. 3:17see we cut
  68. 3:19this in the right
  69. 3:22shape okay now all that is left is to
  70. 3:25remove this water I will spray the tint
  71. 3:27on top so that more
  72. 3:31slippery and I will
  73. 3:34start here in the
  74. 3:51middle okay now that initial part of the
  75. 3:54squeeing is done I'll continue first
  76. 3:57with the felt uh side of the plastic IGI
  77. 4:00to take out more
  78. 4:12water and then I don't know if that's
  79. 4:14visible on the video but I get some
  80. 4:17fingers fingers are where when the the
  81. 4:20film dips up a little bit in like a thin
  82. 4:25long line kind of like a finger and I'm
  83. 4:29getting a few of this here that's quite
  84. 4:30normal this is because of the curvature
  85. 4:32of the film so now I'll use the plastic
  86. 4:35part of the squeegee to push them and I
  87. 4:39might keep getting them for a little bit
  88. 4:41while the film is um drying uh you have
  89. 4:44a few options here if you want to take
  90. 4:46care of this right away uh just grab a
  91. 4:49heat gun or a hair dryer warm it up a
  92. 4:51little bit and that will do it um or uh
  93. 4:56what I prefer to do I think it's uh
  94. 4:58generally safer and
  95. 5:01easier is that I'll just move on to the
  96. 5:03other side and when I'm done with the
  97. 5:05other I'll come back to this and I'll
  98. 5:07push them uh this will give it a little
  99. 5:10time to dry up and drain the water uh so
  100. 5:12that fum can properly stick here but as
  101. 5:16you can see going with a plastic part of
  102. 5:19the squeegee repeatedly and applying a
  103. 5:23decent amount of pressure here uh it
  104. 5:26takes care of them I I started with
  105. 5:28three I think
  106. 5:30and actually right now I'm down to okay
  107. 5:32down to one
  108. 5:35so just push it it will eventually stick
  109. 5:40even on these
  110. 5:42curves but again if you want to expedite
  111. 5:45this and don't want to wait uh you can
  112. 5:48just use a key gun or a hair dryer it do
  113. 5:50just fine and that's pretty much it the
  114. 5:54rear windows are the same uh the the big
  115. 5:58the the door one uh is literally the
  116. 6:00same uh installation technique and the
  117. 6:03small quter panel just spray the film
  118. 6:06spray the the window apply with and
  119. 6:10you're done and uh I think yeah all the
  120. 6:14fingers are
  121. 6:16gone yeah that's pretty much it and this
  122. 6:19is a very easy and great way to save
  123. 6:22hundreds of
  124. 6:23dollars uh from going to the shop you
  125. 6:26can just do it yourself at home and
  126. 6:29again if a finger pops up just push it
  127. 6:33keep checking the installation for like
  128. 6:35an hour um after the installation so
  129. 6:39that if there are any issues like this
  130. 6:41like the fingers you can just push it at
  131. 6:43some point as I said it will stick it
  132. 6:45just needs to be dryer it also depends
  133. 6:47on the weather by the way right now it's
  134. 6:49really cold it's winter time here um and
  135. 6:53cold weather makes this more difficult
  136. 6:54but even in in winter time you can see
  137. 6:57it didn't take that much effort do this
  138. 7:00and in summer it's going to be a lot
  139. 7:02[Music]
  140. 7:06easier when you're done just wipe your
  141. 7:09surfaces so that they're clean as you
  142. 7:11can see it's back to normal and don't
  143. 7:15forget press the door open
  144. 7:17button to lower back your window before
  145. 7:20you can safe close the door thanks for
  146. 7:23watching

About this transcript

This page contains the full transcript of DIY Window Tint for Tesla Model 3 (Gen1 & Highland) by TWRAPS by TWRAPS, generated from the public captions YouTube serves with the video. The transcript has 1,042 words across 146 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to translate the transcript into 100+ languages.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, translation to 100+ languages, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.