YouTube2Text

DIY Saltwater Mixing Station: The Ultimate Aquarium Tool — Transcript

by inventoryking · 2,371 words · 314 segments · language en · Watch on YouTube

Full transcript

  1. 0:00what is going on everybody it's Paul
  2. 0:02nice to be back with you we got a video
  3. 0:04today on a saltwater mixing station this
  4. 0:08is something that I've wanted to do for
  5. 0:09a long time haven't had the chance to
  6. 0:11get around to it but I did now we're
  7. 0:14going to go through it from start to
  8. 0:15finish let's go so my brother does some
  9. 0:183D printing and I asked him if he could
  10. 0:20just design numbers on a line and then
  11. 0:25what we're going to do is install these
  12. 0:26into the inside of the containers
  13. 0:29because they're not
  14. 0:30transparent um you don't know how much
  15. 0:32gallons of water is inside there so I'm
  16. 0:35going to use a meter and fill it up 5
  17. 0:37gallons at a time and then going to
  18. 0:39silicone these into place so I could
  19. 0:42always know about how much is in there
  20. 0:44so what I did was I uh filled these up
  21. 0:47and made the marks how I did it
  22. 0:50originally was like um this and I use
  23. 0:54just normal glue that you would use for
  24. 0:55coral and it just doesn't work they fall
  25. 0:58off so I'm using silicone this time
  26. 1:00so what I did was I got a piece of tape
  27. 1:03put it in here marked where they were so
  28. 1:06then I'll silicone them at the lines and
  29. 1:07it'll be the same amount of water there
  30. 1:09we go got the first one in place now to
  31. 1:12do the
  32. 1:13rest so we got the aquirium safe
  33. 1:16silicone on it we're going to go to the
  34. 1:20mark set it in place and then just kind
  35. 1:24of move it around till I feel it's
  36. 1:26correct which I mean this one's close so
  37. 1:29it looks about about
  38. 1:30right as long as that looks about right
  39. 1:33then I will push it
  40. 1:35down all right now we're letting them
  41. 1:37dry they're in place everything looks to
  42. 1:41match up so silicone you know give it 24
  43. 1:45hours so it dries I mean it's a small
  44. 1:46amount so it'll probably dry faster than
  45. 1:48that and then actually once it dries I
  46. 1:51we'll do a test and see how accurate the
  47. 1:54uh placement is so here we go got the
  48. 1:56number silicon in place I'm using one of
  49. 1:59these save drops so you just click that
  50. 2:02to zero out the top one we're going to
  51. 2:05fill it up and see if it's
  52. 2:17accurate right at the 5 gallon Mark just
  53. 2:19above the line perfect
  54. 2:30[Music]
  55. 2:40all good at the Mark
  56. 2:58[Applause]
  57. 3:03[Music]
  58. 3:10what I'm doing now is I'm going to
  59. 3:11measure where I'm going to put this
  60. 3:13bulkhead I'm going to do 2 in
  61. 3:16away from like it uh it's not a perfect
  62. 3:21measurement but when you go here and you
  63. 3:23slide it across it kind of hits a a lip
  64. 3:26so that was my marking point to start
  65. 3:29with on the other
  66. 3:31one there's our 2in Mark I think that's
  67. 3:34pretty good next piece of the puzzle is
  68. 3:37going to be a hole saw um when you buy
  69. 3:39your bulkheads they suggest what size to
  70. 3:43get so it does it properly so make sure
  71. 3:45you check that so we're going to go
  72. 3:46ahead and drill
  73. 3:53[Music]
  74. 3:57[Applause]
  75. 4:01[Music]
  76. 4:07now that the Hol is drilled out get some
  77. 4:10sandpaper and just kind of smooth up any
  78. 4:14possible
  79. 4:17burs do it on the outside and the inside
  80. 4:21so you could do it one or two ways on
  81. 4:23the inside coming out this way or you
  82. 4:26could do it this way put this here
  83. 4:29tighten it it down and then what you can
  84. 4:31do is uh use one of these that you would
  85. 4:35use like on your aquarium this is meant
  86. 4:36to tighten bulkheads so what I had here
  87. 4:38before was a 40G tank that was my
  88. 4:41quarantine tank since I don't need that
  89. 4:43anymore I'm going to use this area for
  90. 4:45that so we got them both done one and
  91. 4:49two so the next step is we need to
  92. 4:51install float valve I'm going to do it
  93. 4:53up here like I did this one I did a i
  94. 4:59would fill to the 20 Gall Mark I was
  95. 5:02going to originally use these cuz I feel
  96. 5:04like they're better but they are limited
  97. 5:06I didn't get the adjustable ones and I
  98. 5:08had these adjustable ones laying around
  99. 5:10and I feel like where I'd be able to
  100. 5:11mount it in a flat spot it would not
  101. 5:14fill up to the 20 gallon marks so I
  102. 5:16switched to these as you can see right
  103. 5:18there so I've got to drill this and
  104. 5:27install all right got the whole
  105. 5:31drilled this guy goes here uh tighten it
  106. 5:34up all right it's in place now we got to
  107. 5:37just get uh the other part in don't
  108. 5:39forget to put Teflon on here just to
  109. 5:41give yourself Extra Protection from
  110. 5:42leaks
  111. 5:46[Music]
  112. 5:59[Music]
  113. 6:06so I picked these uh 3/4 in ball valves
  114. 6:08off of Amazon they had good reviews they
  115. 6:11were fairly
  116. 6:13inexpensive um and we're going to
  117. 6:15install those on there I'll have links
  118. 6:17in the description to the things I got
  119. 6:19off of Amazon so take a peek um so we're
  120. 6:23going to go ahead and get these
  121. 6:24installed next
  122. 6:28[Music]
  123. 6:36[Music]
  124. 6:43[Music]
  125. 7:23[Music]
  126. 7:27all right let's take a quick peek at
  127. 7:28where we're at in the progress so far so
  128. 7:31got everything hard plumbed into place
  129. 7:34uh this is going to be our Rodi water
  130. 7:36this is going to be salt water and um
  131. 7:39I'll go through the mixing instructions
  132. 7:41once uh they're full of water this is
  133. 7:44going to be in place for when I want to
  134. 7:45do water changes with a hose I could
  135. 7:47fill the tank back up with this um but
  136. 7:50let's take a look so got it hard plumbed
  137. 7:53into here where it's going to mix down
  138. 7:56into the tank pull through that and it's
  139. 8:00just going to keep doing this to mix the
  140. 8:01salt water uh what I did do is I ran
  141. 8:04these um floats one in each one so I
  142. 8:08could fill them both up um with water
  143. 8:11and ran the RO line just got a qu inch
  144. 8:15uh drill bit drilled the hole through
  145. 8:18and ran it through the closet and it
  146. 8:20comes back out on this side so if we go
  147. 8:23and take a look here you could
  148. 8:26see there's where it goes oh of this up
  149. 8:30here and then it goes right through
  150. 8:35there there and then I tied it right
  151. 8:39there we're going to do a quick
  152. 8:41test not going to fill them up yet okay
  153. 8:44we're filling in now I'm going to make
  154. 8:46sure that it stops when the float goes
  155. 8:48up it should but this is just a good
  156. 8:50test okay that's good now let's do this
  157. 8:56one
  158. 8:58okay good good so we are good with the
  159. 9:02RO water coming into the system we're
  160. 9:06making progress all right so here we are
  161. 9:08so far everything's plumbed got this
  162. 9:11tank filled up everything is looking
  163. 9:13good so far got to get this one filled
  164. 9:15up next what I will show everybody is
  165. 9:18how it does transfer it over all right
  166. 9:21so got the pump plugged in we're going
  167. 9:23to move this water into this tank yes I
  168. 9:27have floats on both and did that to set
  169. 9:30it up today uh so I can get both tanks
  170. 9:33full and start making water but let's
  171. 9:34say I'm down to just under 10 gallons of
  172. 9:38water and I want to make more salt water
  173. 9:40so what I would do is I would open this
  174. 9:44valve open this valve make sure that
  175. 9:48these are shut and then we're going to
  176. 9:51go ahead and click uh off the feed
  177. 9:55mode here we go
  178. 9:59so the water is moving in as you can see
  179. 10:04the water level in here is going down so
  180. 10:07it's transferring that water to
  181. 10:13here and then of course shut it off and
  182. 10:17shut it off going to get this top back
  183. 10:19off but that is where we are there now
  184. 10:22if I want to go and start mixing some
  185. 10:24salt water we'll show you that once this
  186. 10:26is full and we're making that water all
  187. 10:29right here's where we left off uh got
  188. 10:32everything done uh had my brother 3D
  189. 10:34print uh these on there so that's
  190. 10:37awesome and he 3D printed a cap that
  191. 10:42works with Unis seals so uh I could have
  192. 10:45everything coming out of the tub but
  193. 10:47it's not going to have an opening for
  194. 10:49evaporation so we got to get all of this
  195. 10:52wire done so I picked these up uh they
  196. 10:56didn't have big ones so I just did them
  197. 10:57back to back and and uh we're going to
  198. 11:00go ahead and get all of this routed down
  199. 11:03in here it's going to look
  200. 11:09nice all right so here we go controller
  201. 11:13board is built um I'm going to have to
  202. 11:15get a new um controller this one
  203. 11:18something's going on with it but this
  204. 11:19one is going to be to warm up the r di
  205. 11:22water when I need to make new salt water
  206. 11:25so I could push over warm ready to go
  207. 11:27water obviously this is for the salt
  208. 11:29water that's the pump and
  209. 11:34uh there you go mix in away then I also
  210. 11:39got these and got everything routed in
  211. 11:42there so at least this part looks clean
  212. 11:45obviously you're going to have some of
  213. 11:46this there's not a whole lot I could do
  214. 11:47about that unless I had another piece to
  215. 11:50go like down the middle or something but
  216. 11:52eh whatever all in all I'm happy with
  217. 11:54the way everything came out uh if I was
  218. 11:57able to have space for bigger ones
  219. 11:59obvious obviously I would go with bigger
  220. 12:00ones but this is what I got and that's
  221. 12:03okay I mean to be able to make water on
  222. 12:06demand like this is going to be
  223. 12:08fantastic and uh freeze up the shower
  224. 12:10freeze up the tub so that's really
  225. 12:14awesome I am happy with it can't wait to
  226. 12:17get things going got to get this thing
  227. 12:19uh glued in place to do the water with
  228. 12:20the hose and we're going to be rocking
  229. 12:23and rolling so I got the salt all
  230. 12:26measured out with uh grams uh how much
  231. 12:29supposed to mix and going to just do a
  232. 12:31little bit at a
  233. 12:33time here we
  234. 12:35go just a little bit at a
  235. 12:42time we'll go ahead and get this uh
  236. 12:46mixed up and hopefully have 1.025 ready
  237. 12:50to
  238. 12:51roll so let's go ahead and go through a
  239. 12:53list of everything that's here most of
  240. 12:55this I got on Amazon so here we go we
  241. 12:58got the python hose which is great from
  242. 13:02Amazon you can see that I have it hooked
  243. 13:04up to the valve to be able to put water
  244. 13:06back in the tanks it works great I do
  245. 13:08want to get a hose Rael for it so that I
  246. 13:11don't have to have it on here and maybe
  247. 13:13even like a quick connect here towards
  248. 13:14just a just easy to work with all the
  249. 13:17ball valves are from Amazon as well 3/4
  250. 13:21in and I'm happy with them they
  251. 13:23definitely do a good job these totes are
  252. 13:27dog food containers
  253. 13:29it's made by vid Vault and these are the
  254. 13:3280 lb the 80 lb rated ones which holds
  255. 13:35the 20 gallons of water these are the
  256. 13:36biggest ones that they have those were
  257. 13:38from Amazon as well then up in here we
  258. 13:41got the ink bird temperature controllers
  259. 13:45great product these are going to uh do
  260. 13:48you well if you get them the
  261. 13:51higher pump also from Amazon make sure
  262. 13:55whatever you get for one of these you
  263. 13:57got to make sure it's an external rated
  264. 14:00pump that's very very important to make
  265. 14:03sure it's an external rated pump now a
  266. 14:05couple other things we got the saltwater
  267. 14:08sign the Rodi sign I asked my brother if
  268. 14:12he can make those and he did and he 3D
  269. 14:14printed them which is fantastic this is
  270. 14:17something that he designed so this right
  271. 14:19this right here is a uni seal he didn't
  272. 14:21Design This I did the uni seal cuz I
  273. 14:24wanted the cords to come out but with
  274. 14:26there being a hole that can cause some
  275. 14:29evaporation so I gave them one and I
  276. 14:31asked him to 3D print uh and design like
  277. 14:35a desk grommet top so um I'm going to
  278. 14:39have them change it a little bit so it's
  279. 14:40a little bit wider for the cords but
  280. 14:42basically this goes on like that now you
  281. 14:45have just a very very very small spot
  282. 14:48which I don't think is going to do
  283. 14:50anything it covers it up and it looks
  284. 14:52great which is fantastic he 3D printed
  285. 14:55these on a file we found online
  286. 14:59also the
  287. 15:01numbers I asked him to do those which
  288. 15:04are all 3D printed these right here are
  289. 15:08desk organizers for cords most of this
  290. 15:11was bought on Amazon I will have
  291. 15:13affiliate links down in the description
  292. 15:15so take a look at that if you're
  293. 15:16interested in getting these there you
  294. 15:18have it the saltwater mixing station
  295. 15:20glad I built it if I was able to have
  296. 15:22room for bigger tubs I would do it but
  297. 15:25it's fantastic being able to make the
  298. 15:27water in one section have to worry about
  299. 15:29a barrel the thing that's nice about the
  300. 15:31barrel is it is bigger but it's all nice
  301. 15:34it's right here where the tanks are it's
  302. 15:35fantastic I definitely like it if you
  303. 15:38enjoyed the video please do leave a like
  304. 15:40and a comment down below if you haven't
  305. 15:41subscribed yet hit that sub button would
  306. 15:43be really appreciated also something to
  307. 15:45keep in mind is I do make shorts on my
  308. 15:47channel so after you see the video go
  309. 15:50ahead and take a look at the shorts tab
  310. 15:52got a whole bunch of things of stuff
  311. 15:54that I have seen uh over the last couple
  312. 15:57years and recorded and posted so take a
  313. 15:59look at all that as well thank you again
  314. 16:01for watching everybody stay Tanked

About this transcript

This page contains the full transcript of DIY Saltwater Mixing Station: The Ultimate Aquarium Tool by inventoryking, generated from the public captions YouTube serves with the video. The transcript has 2,371 words across 314 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.