YouTube transcript (dfGFG0ETsr0) — Transcript
Full transcript
- 0:00You're welcome to this section. In this
- 0:02section, we're going to teach you how to
- 0:04remove an your IC from your board.
- 0:09How to remove or replace a faulty IC on
- 0:13your Android phones. Your faulty IC on
- 0:16your Android How to remove an IC Any
- 0:18kind of IC you want to depending on how
- 0:20the board is. Now, this is the down
- 0:22board
- 0:24of your Tecno phone. Down board of the
- 0:26Tecno phone. Now, we're going to remove
- 0:30this particular IC.
- 0:33Don't worry, I'll show you the diagram.
- 0:35This particular IC. We're going to
- 0:37remove it and replace it back. Should in
- 0:40case maybe this one is particularly
- 0:42fault like it's it's it's damaged. How
- 0:44to replace it back. Do you understand?
- 0:47So, let's get to it. Now, while doing
- 0:49that, you will use this to hold your IC
- 0:52on ground. Now, you're removing this.
- 0:55Most time, when we want to remove some
- 0:56IC, we blow it from under. So, it's get
- 0:59weaker, then we pull it out. But, under
- 1:01here, we have some components that we
- 1:02don't want to destroy. So, what we want
- 1:04to do would be hitting it here to
- 1:06replace it. So, now what do we need to
- 1:08do now? We need to use this our plier
- 1:11to hold this firm on the ground. Then,
- 1:14we use our paste.
- 1:17Mhm?
- 1:18Put it on that particular IC.
- 1:21The reason why we're putting the paste
- 1:22there is that
- 1:24when it's ready to be removed, you'll
- 1:26see some
- 1:28vapor or boiling
- 1:31or boiling on the IC there. So, it's
- 1:33simply that it's ready to be pulled out.
- 1:35Okay?
- 1:36So, now while doing this,
- 1:40our heater should be on the air should
- 1:42be on two,
- 1:44while the heater should be on four.
- 1:46That's how I would do That's how it
- 1:47should be. Then, we use our picker.
- 1:50Wait for it. Let's come this way.
- 1:56I hope you can see it.
- 1:58We need it there.
- 2:00Leave it for like 5 good minutes.
- 2:03Let it heat for good
- 2:05from 3 to 5 minutes.
- 2:08But let it heat for 5 minutes.
- 2:11With this kind of temperature for 5
- 2:12minutes.
- 2:19Well,
- 2:20you'll be checking it within that 5
- 2:21minutes. You see?
- 2:23It is up.
- 2:25Good.
- 2:27The same way we pick it up, that's the
- 2:28same way we're going to replace it.
- 2:30You turn it off.
- 2:32Good. Now, when you turn it off, use
- 2:35your
- 2:37soldering iron to clean up
- 2:40the seat.
- 2:46The seat.
- 2:51Now, you can use
- 2:59soldering lead, okay?
- 3:01Just to make sure that it has enough
- 3:04lead on it, so that when you want to put
- 3:06back the IC,
- 3:08you won't have to be struggling.
- 3:11Good.
- 3:13Now, you've cleaned up the surface of
- 3:14it. But now, we're going to replace this
- 3:16IC back
- 3:18to this. So, how do we do that? We get
- 3:20our blower
- 3:22on the same temperature.
- 3:24The same temperature two and four. Good.
- 3:27We pick up the IC
- 3:29on it.
- 3:34Gently.
- 3:39Drop it there first.
- 3:43Position it.
- 3:46You must really try to position it very
- 3:48well.
- 4:01>> Then
- 4:02you apply the heat on it.
- 4:04Don't touch it again.
- 4:05Just apply it.
- 4:08Apply the heat.
- 4:10You apply it and you see that the
- 4:12surface where you put that lead is
- 4:14getting watery, it's getting
- 4:17watery. You just wait for it for some
- 4:19few minutes. Not up to 5 minutes
- 4:20anymore.
- 4:22Not 5 minutes anymore. You apply a
- 4:23little force on it.
- 4:36You can see.
- 4:47Now you take it off. You off this.
- 4:50Then you wait.
- 4:54You have to blow it so that it can sold.
- 4:57You wait a bit.
- 4:59You wait a bit.
- 5:05You wait a bit.
- 5:08You wait a bit.
- 5:09Let it
- 5:11cool, get cool a bit. Then let's see.
- 5:14Let's see our result. Let's see if it's
- 5:15actually sold.
- 5:18You can see.
- 5:21You can
About this transcript
This page contains the full transcript of YouTube transcript (dfGFG0ETsr0) , generated from the public captions YouTube serves with the video. The transcript has 637 words across 117 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to translate the transcript into 100+ languages.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, translation to 100+ languages, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.