YouTube2Text

Create Complex Mechanical Part from 2D Drawing | CATIA V5 Beginner Solid Modeling Series-52 — Transcript

by Enginuity Lab · 4,147 words · 817 segments · language en · Watch on YouTube

Full transcript

  1. 0:06Hello everyone. Welcome back to In Unity
  2. 0:08Lab. In today's CATIA V5 beginner solid
  3. 0:10modeling series, we'll create this
  4. 0:12complex mechanical component completely
  5. 0:15from this given engineering drawing.
  6. 0:18This tutorial will help you improve your
  7. 0:20skills in sketch creation,
  8. 0:22pad and pocket operation,
  9. 0:24shaft and groove features,
  10. 0:27>> [snorts]
  11. 0:27>> hole creation, multi-section solid
  12. 0:29techniques,
  13. 0:32edge fillets and drafting, reading
  14. 0:34complex engineering drawing, and a main
  15. 0:37important tool here we are going to use
  16. 0:39the Boolean operation
  17. 0:41also in this tutorial. By the end of
  18. 0:44this tutorial, you shall have fully
  19. 0:46completed 3D model ready for
  20. 0:48manufacturing documents.
  21. 0:50Let's get started. Before going to
  22. 0:54CATIA, we always study the drawings
  23. 0:56carefully. Here,
  24. 1:00the overall length
  25. 1:02from the center point of this circle to
  26. 1:04this one is 200 mm.
  27. 1:08The central hole, these two holes,
  28. 1:13and this central
  29. 1:17both section,
  30. 1:19this one, the section A here,
  31. 1:21this is our front view, this is the top
  32. 1:23view, this is section A, and there is
  33. 1:26another section C for this hole.
  34. 1:30Here the details are given here. And the
  35. 1:32side, this rectangular profile hole
  36. 1:36edge,
  37. 1:37the detail is given here.
  38. 1:40Also, we have a sectional cut here
  39. 1:43actual to view the
  40. 1:46this section. Here you can see this
  41. 1:48section to this to see this profile.
  42. 1:50Okay? And also, there are two sides
  43. 1:53hole.
  44. 1:54One is shown here, and another one is
  45. 1:57also from the other side.
  46. 2:01All the dimensions are given here. Like
  47. 2:03here, this radius is 200 mm.
  48. 2:05The Here a
  49. 2:08circular or cylindrical elongated hole
  50. 2:10is also created where this radius is 200
  51. 2:13207 mm. This is 7.5 mm, and this length
  52. 2:18is 32 mm.
  53. 2:33Same way, the corner radius are also
  54. 2:35given. We'll
  55. 2:37find one by one.
  56. 2:39And here, most important thing is we
  57. 2:41always create the add material features,
  58. 2:44then we'll go to remove the material
  59. 2:46from this one.
  60. 2:47So, let's go to CATIA.
  61. 2:49Start, mechanical design, and part
  62. 2:53design.
  63. 2:54I'm renaming this one as complex
  64. 2:59solid
  65. 3:01model.
  66. 3:04And click on okay.
  67. 3:06Now, we are into the part design
  68. 3:08workbench. Here, we'll start from
  69. 3:10creating this profile first, okay? That
  70. 3:13will be created on
  71. 3:14the XY plane. And position the sketch.
  72. 3:18Swap the direction, reverse the V, okay.
  73. 3:21Here,
  74. 3:22what we'll create?
  75. 3:28We'll create this profile. For that, I
  76. 3:30create one hole, the second hole, the
  77. 3:34means the circular portion, the circular
  78. 3:36portion. This have radius 35 mm. And
  79. 3:39this is offset from this line, it is 40
  80. 3:42mm.
  81. 3:43So, we are not going to create right now
  82. 3:46this one. Here, we have a angular
  83. 3:49section, and that is 22° at angle. Okay?
  84. 3:54And this radius is 35 mm at this corner.
  85. 3:57And also here a radius of 200 mm. So,
  86. 4:01what I will do, I'll create a circle at
  87. 4:04this point. Okay?
  88. 4:07And the diameter radius of this one
  89. 4:10Here it is given radius
  90. 4:1435 mm. So, make it radius
  91. 4:1735.
  92. 4:18Okay?
  93. 4:19And also the distance from the center
  94. 4:22line it is
  95. 4:25200 for
  96. 4:26from this one to this one. That means it
  97. 4:28is 100 mm on this one. 100 mm.
  98. 4:31Okay? Now, we create a circle. Now, I
  99. 4:34will mirror this one to the other end.
  100. 4:39Then, we'll create
  101. 4:42this one. This radius 200 mm here. Here,
  102. 4:45I will use the
  103. 4:47corner tool or we can use the
  104. 4:49three-point circle actually.
  105. 4:52Three-point arc
  106. 4:54or
  107. 4:56try tangent
  108. 4:58arc or
  109. 5:02Here, if I use the three-point arc, then
  110. 5:05this will be like this one.
  111. 5:07This one
  112. 5:08and this one. And then make this
  113. 5:11to circle or arc
  114. 5:14at tangency.
  115. 5:16Okay? Now, give the radius
  116. 5:20200 mm.
  117. 5:22Okay? Next to create
  118. 5:26a line
  119. 5:28I can use a axis line here.
  120. 5:31Create a axis line
  121. 5:33here.
  122. 5:35Okay? And
  123. 5:38create another line
  124. 5:40which will be connect to this one and
  125. 5:42make this one and this one to be
  126. 5:44tangent.
  127. 5:46Okay? Same way, I can mirror this one to
  128. 5:49the other end.
  129. 5:51And then I can give this angle
  130. 5:55as 22°.
  131. 5:58Okay, next to create the corner radius
  132. 6:01here. That means I have to select the
  133. 6:03corner
  134. 6:04corner point corner then the radius here
  135. 6:06it is.
  136. 6:07How much radius is given? It's radius
  137. 6:0935.
  138. 6:1235
  139. 6:14Okay, now our sketch is created. Now
  140. 6:17need to remove the extra element from
  141. 6:19here. For that I will use the quick trim
  142. 6:21tool.
  143. 6:22This one
  144. 6:23and this one.
  145. 6:25Now I can exit the workbench and use the
  146. 6:29pad tool to create the thickness here.
  147. 6:31What is the thickness here? Here it is
  148. 6:33given 60 mm. Okay.
  149. 6:36So we can make this thickness here. That
  150. 6:39means 60 mm thickness. So click on
  151. 6:42and it is 60 mm.
  152. 6:45Okay, now
  153. 6:47we have created this section.
  154. 6:49We need to create this section as well.
  155. 6:51For that what I will do, either we can
  156. 6:53use the pocket tool but here I am going
  157. 6:56to use the Boolean operation. For that
  158. 6:58to use the Boolean operation I need
  159. 7:00another body. For that we know how to
  160. 7:03insert a body. Go to insert and body.
  161. 7:06Now
  162. 7:07set the body to as defined
  163. 7:10work object. Now I can click on the YZ
  164. 7:14plane.
  165. 7:15Position the sketch. Okay.
  166. 7:20Now
  167. 7:21we'll create this profile.
  168. 7:25Okay.
  169. 7:26That will be
  170. 7:27like this.
  171. 7:29This one.
  172. 7:31This one.
  173. 7:36This one. This one.
  174. 7:42This is parallel to this one.
  175. 7:47Same way this is also parallel to this
  176. 7:49one.
  177. 7:54And this will connect to this one. This
  178. 7:57is the profile shape. Okay?
  179. 8:00Now, I will make all the symmetry first.
  180. 8:04That means
  181. 8:05double click on the constant tool, this
  182. 8:07one and this one to be
  183. 8:10symmetry here.
  184. 8:12Same way
  185. 8:14these two points also symmetry.
  186. 8:19To this one, these two actual
  187. 8:22no symmetry line to this one. Same way
  188. 8:25we can make this one actual.
  189. 8:27As this is not required,
  190. 8:30why it is not required? Because I have
  191. 8:32created this one and this one parallel
  192. 8:34to this one. So, it will not required to
  193. 8:36create this one actual. But, we are
  194. 8:38creating the symmetry.
  195. 8:41Okay? Now,
  196. 8:43here you can see this is 32 mm. That
  197. 8:46means overall everywhere it is 32 mm.
  198. 8:49So, I can make this length is 32 mm.
  199. 8:55Okay?
  200. 8:58This one actual 32 mm.
  201. 9:04And this one is already created. Same
  202. 9:06way this one actual.
  203. 9:1032
  204. 9:11Also this one.
  205. 9:14As this is creating over constant, so we
  206. 9:17will not create that one.
  207. 9:20I will delete this one.
  208. 9:22Now, we are created this. Now, it's time
  209. 9:24to give the
  210. 9:26lengths. Okay? Here you can see this
  211. 9:29length it is not given
  212. 9:32here.
  213. 9:34Here it is not given the total length,
  214. 9:36but we know what is the length here
  215. 9:38because 200 mm plus 35 mm.
  216. 9:4235 mm is a radius, then we can add the
  217. 9:4570 mm to this one. That means 270 mm.
  218. 9:48So, I can make it
  219. 9:53270 mm. 270.
  220. 9:55Okay? Next is what? Why it is not
  221. 9:58getting fully constant? That means
  222. 10:01here you can see there is a angle of 40°
  223. 10:04here it is. So, I can make this angle
  224. 10:0740° and this length from
  225. 10:10this one to this point it is 66 mm. So,
  226. 10:16this is 66.
  227. 10:21Okay? And this angle given it is 40°.
  228. 10:2840°.
  229. 10:29Now, also I have to give this length
  230. 10:33where it is 60 mm.
  231. 10:35Okay? Now, you can see our model sketch
  232. 10:39is ready.
  233. 10:41Where the all the lines are in green,
  234. 10:43that means it is fully constant.
  235. 10:46Now, click on the exit workbench.
  236. 10:50Now, use the pad tool
  237. 10:53and
  238. 10:54mirror the extent by 100 mm.
  239. 10:59Now, you can see there are two
  240. 11:02solid model we have created solid body
  241. 11:04we have created. What to do here? Select
  242. 11:07the body two, right click body two
  243. 11:10object, and then you can find the
  244. 11:12Boolean operations here. Here I will use
  245. 11:14the intersect operation to create this
  246. 11:17intersection.
  247. 11:19Now, you can see
  248. 11:20this profile is created.
  249. 11:22That will be you can see from
  250. 11:25your
  251. 11:26isometric views.
  252. 11:28Okay? This is created.
  253. 11:30Here we create the add material
  254. 11:32features. This is the add material for
  255. 11:34this one. Now, it's time to remove the
  256. 11:36material from this one.
  257. 11:38Okay, from here
  258. 11:41how we can what to remove? First, we'll
  259. 11:43remove this section, this circle, and
  260. 11:46this
  261. 11:48elongated hole profile. Okay, here the
  262. 11:50circle this diameter given it is 50 mm.
  263. 11:53So,
  264. 11:55click on
  265. 11:56the XY plane.
  266. 11:59Click on the position sketch.
  267. 12:01Swap the direction, reverse the V. Okay.
  268. 12:04Then,
  269. 12:05create a circle.
  270. 12:09And make this circle as concentricity to
  271. 12:13this one.
  272. 12:16And give the diameter as 50 mm.
  273. 12:23Here, change it to diameter.
  274. 12:2650 mm.
  275. 12:27Okay.
  276. 12:28Now,
  277. 12:30we'll create this slot here.
  278. 12:33How to create that one? For that, I will
  279. 12:35use
  280. 12:36elongated hole command.
  281. 12:41Okay.
  282. 12:42Then, start from here from the center
  283. 12:45point and create a elongated hole like
  284. 12:48this.
  285. 12:52Created.
  286. 12:53Next is to
  287. 12:55give the dimension for this hole.
  288. 12:57Here, it is given 40 8 mm length and 1.5
  289. 13:02mm radius.
  290. 13:03Okay, and also the angle here it is 22°.
  291. 13:07So,
  292. 13:09this angle first, give this angle. This
  293. 13:12is 22°.
  294. 13:15This radius it is
  295. 13:171.5 mm.
  296. 13:20And this length
  297. 13:22when I select the cent-
  298. 13:25center length, then I can directly give
  299. 13:27the length here. This is 48 mm.
  300. 13:30Okay? Now,
  301. 13:34still it is not fully constant. Why?
  302. 13:36Because this center point and this
  303. 13:38center point is not aligned. Now, make
  304. 13:41them
  305. 13:43Select this point. Select this point.
  306. 13:47and coincidence. Now, you can see this
  307. 13:49is fully constant. Now, you do quick
  308. 13:52trim tool to trim the extra lines from
  309. 13:55here.
  310. 13:58And this line actually. Now, it is
  311. 14:00making this one edge.
  312. 14:07Now, this is making this one not
  313. 14:09constant. So, what to do? Select these
  314. 14:11two lines and say parallelism.
  315. 14:15Okay. Now, our sketch is fully green or
  316. 14:19fully constant. Now, select this profile
  317. 14:23and use the mirror tool. Mirror about
  318. 14:25the vertical axis to the other side.
  319. 14:28Okay? Now, click on the exit workbench.
  320. 14:32And use the pocket tool
  321. 14:35and say up to next.
  322. 14:37Okay.
  323. 14:39Now, this section is created. Next is to
  324. 14:43Next, we will create this section. Where
  325. 14:45we have this one, you can see.
  326. 14:47Okay? How to create that one?
  327. 14:50For that, here you can see this is there
  328. 14:53is a we will create a plane of 16 mm
  329. 14:57from the base line.
  330. 14:59We will create a plane here.
  331. 15:01Okay. So,
  332. 15:04create a plane. Click on the plane and
  333. 15:07create a plane
  334. 15:09offset from the XY plane by 16 mm.
  335. 15:13Okay? Now, click on this plane.
  336. 15:16Position the sketch.
  337. 15:18Swap the direction. Reverse the V. Okay.
  338. 15:21Here, create a circle
  339. 15:26of diameter 33 mm.
  340. 15:29Okay?
  341. 15:30And this one
  342. 15:32and this one to be concentricity.
  343. 15:36Okay? Same way,
  344. 15:38I will project this
  345. 15:41outer line here. Not the diameter, here
  346. 15:44it is the radius. 33 mm.
  347. 15:48Okay? I will project this line like this
  348. 15:51and I will create a
  349. 15:55straight line from here.
  350. 15:59This line to be coincide with this one.
  351. 16:05Coincidence. Now,
  352. 16:07trim the extra lines. This one, this
  353. 16:10one,
  354. 16:13this one,
  355. 16:15this one as well. And also project
  356. 16:18another line.
  357. 16:20This line
  358. 16:21and trim this.
  359. 16:26Now, this section is created. Now,
  360. 16:28use the mirror tool
  361. 16:30to create it to the other side.
  362. 16:35Okay? Now, this one, make this two
  363. 16:40edge concentricity.
  364. 16:44Okay?
  365. 16:46Now, this is also fully constrained.
  366. 16:49Now, click on the exit workbench.
  367. 16:52Here, use the pocket tool.
  368. 16:55How much we can pocket it?
  369. 16:58Here it is given 17 mm.
  370. 17:00The total length it is 17 mm. So, I can
  371. 17:03make
  372. 17:04dimension
  373. 17:0617 by 2
  374. 17:08and mirror the extent. So, it will
  375. 17:10create both the side.
  376. 17:12Total length is 17 mm. Okay.
  377. 17:16Now, you can see this section is
  378. 17:17created.
  379. 17:19Okay. Next is to create
  380. 17:23Here we have create
  381. 17:25the side profiles. Now we'll create this
  382. 17:28circle first. The this portion, the
  383. 17:30circular this portion.
  384. 17:34Sir center hole.
  385. 17:37Okay.
  386. 17:38For that
  387. 17:40Here you can see this is 40 mm offset
  388. 17:42from this line. So I can create another
  389. 17:45plane
  390. 17:47offset by 40 mm
  391. 17:51from the YZ plane.
  392. 17:53Okay. And click on this plane.
  393. 17:56Position the sketch. Okay.
  394. 18:00Say fit all.
  395. 18:02Now here you can see
  396. 18:07this is created like this. Here it is 50
  397. 18:09mm. This is 24 mm. This is 43 mm. This
  398. 18:12is 11 mm. This is 5 mm and two chamfer,
  399. 18:162 into 45 degree chamfer here created.
  400. 18:19So what I can do
  401. 18:22I can create a line here first.
  402. 18:24Then this will be my profile.
  403. 18:31Okay. Now make this line as well
  404. 18:35horizontal.
  405. 18:36Now double click on the constant tool.
  406. 18:38This line to be coincide with this one.
  407. 18:41Coincidence. Same with this line to be
  408. 18:43coincidence with this one.
  409. 18:45Coincidence.
  410. 18:47And this length given it is 11 mm and
  411. 18:50from the below it is 5 mm.
  412. 18:53This is 11 mm.
  413. 18:55And this is 5 mm.
  414. 19:00This is 11.
  415. 19:04This is 5.
  416. 19:07And
  417. 19:08this diameter
  418. 19:10Here it is given 50 mm. That means I can
  419. 19:13make it 25 mm.
  420. 19:16I will use the groove tool, that's why I
  421. 19:18am using
  422. 19:20creating the half section of this one.
  423. 19:21This diameter is 24 mm.
  424. 19:2524 by 2.
  425. 19:28And this one is 43 by 2.
  426. 19:33Okay, now my sketch is ready. It is
  427. 19:35fully constant. Click on the exit
  428. 19:37workbench. Before that,
  429. 19:42I will create a axis here.
  430. 19:44Okay. This axis will help me to create
  431. 19:47the groove here. Okay. Now, I have
  432. 19:50created axis, but the axis is not
  433. 19:52visible in this
  434. 19:54part workbench. This is visible only in
  435. 19:56the sketcher workbench. Now, I will use
  436. 19:58the groove tool.
  437. 20:00Select the sketch five.
  438. 20:02Then,
  439. 20:03you can see the sketch axis is already
  440. 20:06selected here. Okay.
  441. 20:08Otherwise, it will create problem. And
  442. 20:10okay.
  443. 20:13Now, this
  444. 20:15central hole is created.
  445. 20:17Next to create the
  446. 20:22cylindrical elongated hole. For that,
  447. 20:28I will click on
  448. 20:30the XY plane.
  449. 20:33Position the sketch.
  450. 20:35Swap the direction, reverse the V. Okay.
  451. 20:39Here, I will create a cylindrical
  452. 20:43elongated hole. So, click on the
  453. 20:45cylindrical elongated hole.
  454. 20:46Then,
  455. 20:47on the vertical axis, I will put my
  456. 20:49center line
  457. 20:51and circle.
  458. 20:52Then, the cen-
  459. 20:54center line, then this one.
  460. 20:56Okay.
  461. 20:57Now,
  462. 21:00I will make
  463. 21:03this point and this point
  464. 21:06symmetry about
  465. 21:09the vertical axis.
  466. 21:10Okay? And here the radius it is given
  467. 21:177.5. So, make it 7.5.
  468. 21:21Okay?
  469. 21:27Now, this radius.
  470. 21:31The main thing is this radius where it
  471. 21:34is given 200 mm.
  472. 21:37Okay? When I make this one, then this
  473. 21:39will go till this one. So,
  474. 21:41try to
  475. 21:43take it here.
  476. 21:48And this length it is
  477. 21:52from this point to this point
  478. 21:55it is
  479. 21:59below symmetry line about this one. It
  480. 22:02is already created. So, this is 32 mm.
  481. 22:06Okay?
  482. 22:08Now, the main thing is to where we can
  483. 22:10place this one.
  484. 22:12Here, what we'll do I Now, here you can
  485. 22:15see this radius is given 207 mm.
  486. 22:19Here,
  487. 22:20can see this radius is 207 mm. And then
  488. 22:24I can make this circle and this circle
  489. 22:29at concentricity, then you can see this
  490. 22:32is making fully constant here. Now,
  491. 22:34click on the exit workbench
  492. 22:36and then I can use the pocket tool and
  493. 22:39say
  494. 22:40up to next and okay. Now,
  495. 22:44we have create this slot edge well.
  496. 22:46Now, it's time to create
  497. 22:48this one.
  498. 22:50This side
  499. 22:51one. Okay? Here,
  500. 22:54how to create that one?
  501. 22:56Here you can see this is 52 mm from here
  502. 22:58and this is 8 mm from here. So,
  503. 23:01let's start by create selecting the XY
  504. 23:03plane first, position the sketch.
  505. 23:07Swap the direction, reverse the V. Okay.
  506. 23:10Here also, to create that one, I'll use
  507. 23:13the profile tool. Then, this will be my
  508. 23:16profile created.
  509. 23:17This will be
  510. 23:18perpendicular to this one.
  511. 23:20Then this one and
  512. 23:23this one.
  513. 23:25Okay, here remove the horizontal and
  514. 23:29these two lines.
  515. 23:33This line and this line is
  516. 23:36parallelism.
  517. 23:38Make these two parallelism.
  518. 23:40Okay. Now,
  519. 23:43we can start in the detail
  520. 23:47B. Here you can see.
  521. 23:49And also here actually, this is 22°
  522. 23:52first. This is 8 mm offset from this
  523. 23:54one. So, make this one 8 mm offset. That
  524. 23:57means this line and this line to be
  525. 24:00parallelism.
  526. 24:03Okay. And this offset is 8 mm.
  527. 24:08This is 8 mm.
  528. 24:10Okay.
  529. 24:11Now,
  530. 24:13this length is given actually.
  531. 24:15What is the length? This is 15 mm and
  532. 24:17this is 22°. This is 15 mm.
  533. 24:23And this angle
  534. 24:26it is 22°.
  535. 24:30And another length is given 13 mm from
  536. 24:33this one, but this is from the center of
  537. 24:35this radius six, where we have put
  538. 24:39all the four radius, four corners of
  539. 24:41radius six. So,
  540. 24:44first select all these four corners.
  541. 24:47This one, this one,
  542. 24:50this one, this one, click on the corner
  543. 24:52tool.
  544. 24:54Here, in the radius value, keep 6 mm.
  545. 24:58And
  546. 24:59yes, now it is created like this but we
  547. 25:02need to give another dimension like this
  548. 25:05center point and this line. It is
  549. 25:0913 mm. Okay, make this one
  550. 25:1213 mm.
  551. 25:15And also what is the next dimension to
  552. 25:17give? This dimension this 52 mm from the
  553. 25:20center line to this line. Okay.
  554. 25:23So
  555. 25:25the vertical axis
  556. 25:27to this one. It is 52 mm.
  557. 25:34Okay, here it is showing that there is
  558. 25:39a over constant created so delete this
  559. 25:41one as it is
  560. 25:45or delete this one.
  561. 25:49As this is not required.
  562. 25:52Now
  563. 25:53we can make
  564. 25:55the symmetry of this one for that click
  565. 25:58on select this one mirror it to the
  566. 26:00vertical axis and click on the exit
  567. 26:03workbench and pocket it to up to next.
  568. 26:07Okay.
  569. 26:09Now this is also created. Next is to
  570. 26:12create
  571. 26:13this side hole.
  572. 26:16One is here and another one is here.
  573. 26:18Here how we can create this side hole?
  574. 26:20For that I will select this plane. Okay.
  575. 26:24The 16 mm offset plane one.
  576. 26:28And position the sketch.
  577. 26:31Here swap the direction reverse the V
  578. 26:33and say okay.
  579. 26:35Then I will create a axis line first.
  580. 26:39Okay, this is my axis line.
  581. 26:42And here I will start from here.
  582. 26:45This one.
  583. 26:47This one. This one.
  584. 26:50This one.
  585. 26:51And
  586. 26:53with this one. And
  587. 26:55close it. Okay, this is the profile
  588. 26:58here. Here also you can see this is the
  589. 27:00profile created. I will use the group
  590. 27:02tool, that's why I'm creating the half
  591. 27:03section. Here this diameter is 14 and
  592. 27:06this is diameter eight and this length
  593. 27:08is 10 mm. Okay, so what I'll do
  594. 27:13First, this line to be coincide with
  595. 27:15this one.
  596. 27:19Okay. Now, this diameter
  597. 27:23it is 14, that means 14 by two.
  598. 27:26And this diameter is
  599. 27:338.5.
  600. 27:34Eight, that means
  601. 27:36eight by two.
  602. 27:38And this length is it is given 10 mm.
  603. 27:43Make it 10 mm.
  604. 27:44Okay. Now, also
  605. 27:47here it is given this is 33 mm from this
  606. 27:50center to this one and 22 mm on this
  607. 27:54side. So
  608. 27:56for that I'll create a point.
  609. 28:01That will be concentricity to this one.
  610. 28:06And make this point as construction
  611. 28:08element. Okay. Now
  612. 28:10click on this point
  613. 28:12to this one. This is 33 mm.
  614. 28:17Same way
  615. 28:18this point to this one.
  616. 28:21And
  617. 28:22the
  618. 28:27Here also create a reference line.
  619. 28:31Okay.
  620. 28:33This line to be perpendicular to this
  621. 28:36one. Make this one perpendicular.
  622. 28:39And this length this line to this one it
  623. 28:42is
  624. 28:54>> As this is going here, so I can
  625. 28:56delete this constant.
  626. 28:58Now, this one
  627. 29:00to this one, it is 22 mm.
  628. 29:04Okay?
  629. 29:06Now, here I can make a
  630. 29:09angular section
  631. 29:11of
  632. 29:1560°.
  633. 29:18Okay?
  634. 29:22Now, click on the exit
  635. 29:23exit workbench
  636. 29:25and use the group tool.
  637. 29:28Here also, you can see the selection
  638. 29:30axis is already selected. Axis is
  639. 29:32selected by the sketch axis itself
  640. 29:34because you have created the axis inside
  641. 29:36the sketch. Okay.
  642. 29:39Okay. Now, this section is created.
  643. 29:42Next is to create
  644. 29:44it create this to the other side. For
  645. 29:46that, I will select the group and then I
  646. 29:48will use the mirror tool from the 3D
  647. 29:51part design workbench and select this
  648. 29:54plane
  649. 29:55as my mirroring object, the ZX plane.
  650. 29:58And okay.
  651. 30:01Okay. This is created to the other side
  652. 30:04as well.
  653. 30:05Same way, I can create we will create
  654. 30:08the last hole, this one, where this is
  655. 30:11given like this. Diameter 22 and 28 from
  656. 30:16the base line. And this diameter is
  657. 30:1810.5. For that, I will select this
  658. 30:21plane, XY plane, position the sketch.
  659. 30:24Solve the direction, reverse the V.
  660. 30:26Okay.
  661. 30:27And I will create two points here. One
  662. 30:29point here and another point here. And
  663. 30:33these two points are
  664. 30:35symmetry about
  665. 30:37the vertical axis. And
  666. 30:39the length
  667. 30:41between them the distance between them
  668. 30:44it is given here
  669. 30:4580 mm and 20 mm from this one. So, this
  670. 30:49is 80 mm.
  671. 30:53And
  672. 30:5420 mm from this plane.
  673. 30:58Okay. Now, click on the exit workbench.
  674. 31:01We have two points.
  675. 31:03I'll select the whole tool.
  676. 31:04Then, select this point and
  677. 31:08select this plane.
  678. 31:11Okay.
  679. 31:12And here say up to next. The diameter
  680. 31:15here, what is the through hole diameter?
  681. 31:16It is 10.5 mm.
  682. 31:18And the counter diameter is 22 mm. 10.5
  683. 31:21mm here.
  684. 31:23In the type, make it counter bore. This
  685. 31:26is diameter 22 mm and the depth
  686. 31:3122 mm and the depth from the base it is
  687. 31:3428 mm. That means we can make it 28.
  688. 31:39Preview.
  689. 31:42Depth is 28 mm.
  690. 31:50Here
  691. 31:51change the direction and in the type
  692. 31:54here length is 28 mm.
  693. 31:56Preview and okay.
  694. 31:59So, here one this hole is created.
  695. 32:01Again, use the whole tool and select
  696. 32:04this
  697. 32:05point
  698. 32:06this plane
  699. 32:08and reverse the direction and say okay.
  700. 32:12Now, our two holes also created. So, we
  701. 32:16create all the holes, all the rim
  702. 32:19we create the add material features,
  703. 32:20then we remove the material from the
  704. 32:22model. Then, it's time to give the
  705. 32:26dress-up features.
  706. 32:27What are the dress-up features here?
  707. 32:30Here you can see this radius 20
  708. 32:33on this one and this one, radius 19 on
  709. 32:36this one and the this one inside corner
  710. 32:38and radius 30 on all these four corners.
  711. 32:41So,
  712. 32:42first start with
  713. 32:44select the edge fillet.
  714. 32:45This one
  715. 32:47and this one it is 20 mm.
  716. 32:51And the inside edge it is
  717. 32:58this one
  718. 33:00and this one it is 19 mm.
  719. 33:04Now,
  720. 33:09this one
  721. 33:13this one
  722. 33:15this one
  723. 33:17and this one as 30 mm.
  724. 33:23Preview and okay.
  725. 33:30So, as we are not able to create this
  726. 33:33one here, what I will do
  727. 33:36I'll go to body two and in the sketch
  728. 33:39two I can create the radius here.
  729. 33:43This point
  730. 33:48this point, this point and this point
  731. 33:52and give the radius as 30 mm.
  732. 33:57Now, click on the exit workbench.
  733. 34:01Now, you can see this is also created
  734. 34:03here.
  735. 34:04Okay, this radius is also created. Next
  736. 34:07is to
  737. 34:08give another fillets this radius two
  738. 34:12and two here
  739. 34:13both the sides. Click on the edge
  740. 34:15fillet.
  741. 34:18This one
  742. 34:19and this one edge it is created tangency
  743. 34:22to everywhere, it will
  744. 34:25propagation in
  745. 34:26tangency then only give the radius two.
  746. 34:28Only select these two edges and okay.
  747. 34:32Here also
  748. 34:35we have radius. Here it is 2 mm. Here it
  749. 34:39is 2 mm. Here it is 2 mm. So, what we
  750. 34:41will do
  751. 34:42we can edit the edge fillet
  752. 34:45three and give this radius as well. This
  753. 34:48one.
  754. 34:50This one.
  755. 34:55This one.
  756. 34:57This one.
  757. 34:59And
  758. 35:00in the back side as well.
  759. 35:04Or I can select this one.
  760. 35:08This one.
  761. 35:10And this one.
  762. 35:12Okay.
  763. 35:15Now, it's time to give the
  764. 35:18chamfer here.
  765. 35:19Here we have a chamfer of 2 into 45
  766. 35:21degree. This corner and this corner. So,
  767. 35:24I can use the chamfer tool.
  768. 35:27This corner.
  769. 35:28And this corner. The angle length is 2
  770. 35:31mm. Angle is 45 degree. Preview and
  771. 35:33okay.
  772. 35:36Now, here you can
  773. 35:39verify the model.
  774. 35:41As we have completed
  775. 35:44all the details from this one.
  776. 35:47And
  777. 35:50now you can verify your model. I have
  778. 35:53set my screen into
  779. 35:57two different section. Here I have split
  780. 36:00my screen into two. So, we can verify
  781. 36:02our model. You can verify the
  782. 36:05boss location.
  783. 36:06Hole sizes, slot dimension, pocket
  784. 36:09depth, fillet radius, overall
  785. 36:11dimensions.
  786. 36:15And compare your 3D model to your
  787. 36:18isometric views as well. Here you can
  788. 36:20see if I go from this view, you can see
  789. 36:23this view.
  790. 36:24Okay.
  791. 36:25And from this view, you can see this
  792. 36:27view.
  793. 36:29Now, it's time to apply the material to
  794. 36:32this model. How to apply the material?
  795. 36:34As you know,
  796. 36:36select the solid complex model and apply
  797. 36:39material.
  798. 36:41Then, from the metal section, I will
  799. 36:43select the steel here. Apply material
  800. 36:46and okay. To visualize the material, I
  801. 36:49can select the shading with material to
  802. 36:51visualize the material. Here, you can
  803. 36:53see I have applied the material to this
  804. 36:56one. And also, in the specification
  805. 36:58tree, you can see steel is applied to
  806. 37:00this one.
  807. 37:01Okay? Now, go back to shading with
  808. 37:04edges.
  809. 37:06And that's how we create this complex
  810. 37:08mechanical component
  811. 37:10in CATIA V5 from the 2D engineering
  812. 37:13drawing. If you found this video
  813. 37:15helpful, please like the video, share
  814. 37:18with your friends, and subscribe to
  815. 37:19Engineers City Lab for more CATIA V5
  816. 37:21tutorials. Thanks for watching Engineers
  817. 37:23City Lab. See you on next video.

About this transcript

This page contains the full transcript of Create Complex Mechanical Part from 2D Drawing | CATIA V5 Beginner Solid Modeling Series-52 by Enginuity Lab, generated from the public captions YouTube serves with the video. The transcript has 4,147 words across 817 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.