Before Fridges, Scientists Liquefied Air - Here's How — Transcript
Full transcript
- 0:00Take a look at this.
- 0:02Woah.
- 0:03Rapidly compressing the air in the tube
- 0:06actually made it hot enough to ignite a
- 0:08little piece of cotton.
- 0:10Now watch closely when I pull the
- 0:11plunger out when there's some water in
- 0:14there. You can just about make out a
- 0:16very fine mist. When I reduced the
- 0:19pressure, the water vapor in the humid
- 0:21air cooled down and condensed into tiny
- 0:24droplets. So changing the pressure can
- 0:27change the temperature and it can help
- 0:29turn a gas into a liquid. But try doing
- 0:32that with oxygen. For decades,
- 0:35scientists pressurized it and cooled it
- 0:37using increasingly extravagant
- 0:39experiments. It still refused to become
- 0:41a liquid.
- 0:43Nitrogen and hydrogen were just as
- 0:44stubborn and together they became known
- 0:46as the permanent gases. Yet scientists
- 0:49eventually found a way to liquefy all
- 0:51three. And as we're about to see, the
- 0:54engineering required to do this was
- 0:56absolutely incredible.
- 0:59It all started over 200 years ago when
- 1:01Michael Faraday used pressure to liquefy
- 1:04chlorine. In 1823, Faraday was
- 1:07investigating chlorine hydrate, a solid
- 1:09containing chlorine and water.
- 1:12At Humphrey Davy's suggestion, he sealed
- 1:14some inside a glass tube and heated it.
- 1:17In Faraday's own words, the tube became
- 1:19filled with a bright yellow atmosphere
- 1:21and on examination was found to contain
- 1:24two fluid substances.
- 1:26He saw a faint yellow watery liquid
- 1:28sitting on top of a bright yellow denser
- 1:31liquid.
- 1:32As the tube cooled, even more of this
- 1:34yellow liquid appeared.
- 1:36To any chemists watching, you might
- 1:37think straight away that the bright
- 1:38yellow atmosphere must be chlorine and
- 1:40the faint yellow liquid is just water
- 1:42with some of the chlorine dissolved in
- 1:44it.
- 1:44But what about the bright yellow liquid
- 1:46in a separate layer?
- 1:47Why did that form?
- 1:49Opening the tube provided an important
- 1:51clue. The yellow liquid rapidly
- 1:53disappeared releasing chlorine gas while
- 1:55the watery liquid remained.
- 1:57It appeared that Faraday had obtained
- 1:59chlorine. The sealed tube was crucial.
- 2:03Since liquid molecules are closer
- 2:04together compared to gas molecules, as
- 2:07chlorine gas was released from the
- 2:08hydrate, pressure built up inside,
- 2:11forcing the molecules together and
- 2:13allowing some of the chlorine to exist
- 2:15as a liquid under conditions where at
- 2:17ordinary atmospheric pressure it would
- 2:19have to be a gas. As Faraday put it, the
- 2:22chlorine had been entirely separated
- 2:24from the water by the heat and condensed
- 2:26into a dry fluid by the mere pressure of
- 2:29its own abundant vapor.
- 2:31To prove it, Faraday used a condensing
- 2:33syringe, very similar to the apparatus I
- 2:35used at the beginning of the video.
- 2:37He introduced chlorine into a tube and
- 2:39forced air in above it, compressing the
- 2:42chlorine underneath.
- 2:43Once again, the yellow liquid appeared.
- 2:46In doing so, he'd proven that chlorine
- 2:48could be liquefied using pressure. Now,
- 2:50it should go without saying that
- 2:52experimenting with pressurized gases can
- 2:54be very dangerous. During one
- 2:56experiment, an exploding vial sent 13
- 2:59shards of glass into Faraday's eye.
- 3:02But after his success liquefying
- 3:03chlorine, the next question was, could
- 3:06pressure be used to liquefy other gases?
- 3:09In 1845, Faraday published a summary of
- 3:12a much more ambitious series of
- 3:13experiments where his object was to
- 3:16subject the gases to considerable
- 3:17pressure with considerable depression of
- 3:20temperature.
- 3:21This time, he used powerful compression
- 3:23pumps to compress a gas into a tube.
- 3:26Then, while the pumps were maintaining
- 3:27the high pressure, he dipped the tube
- 3:30into a bath of solid carbon dioxide,
- 3:32what we now call dry ice, and ether. But
- 3:35he had another trick up his sleeve to
- 3:36make the bath even colder.
- 3:39Molecules are constantly escaping from
- 3:41the surface of a liquid while some vapor
- 3:43molecules return to it. By removing the
- 3:46vapor above the liquid, we reduce the
- 3:48number coming back, so more liquid can
- 3:50turn into gas. In other words, when you
- 3:53lower the pressure, the liquid starts
- 3:55evaporating more quickly.
- 3:57These escaping vapor molecules take heat
- 3:59with with and cool the remaining liquid
- 4:02down.
- 4:03Incidentally, this evaporative cooling
- 4:05is essentially how sweat cools you down.
- 4:08Faraday applied a similar principle to
- 4:10his bath.
- 4:11By using an air pump to remove the air
- 4:13and carbon dioxide vapor above the bath,
- 4:15he encouraged the solid CO2 to turn into
- 4:18a gas more quickly, drawing energy from
- 4:20the mixture and making its temperature
- 4:22drop further.
- 4:23Now he could combine the high pressure
- 4:25inside the glass tube with exceptionally
- 4:28low temperatures outside it.
- 4:30This setup worked beautifully to allow
- 4:32him to liquefy a load of gases, but
- 4:35oxygen, nitrogen, and hydrogen still
- 4:37refused to cooperate. At this point,
- 4:39Faraday suspected that simply building a
- 4:41stronger pump wasn't necessarily the
- 4:44answer. Maybe something like this crazy
- 4:46contraption would do the trick. This
- 4:49apparatus was constructed by the French
- 4:50physicist Louis Paul Cailletet, who on
- 4:53the 2nd of December 1877 used it to do
- 4:56something really cool. Here's how it
- 4:58worked. Cailletet filled this central
- 5:01glass capillary tube with oxygen gas.
- 5:03The tube fed down into a chamber which
- 5:05was filled with mercury, so the oxygen
- 5:08was sealed off by the mercury below it.
- 5:10Around the capillary tube was a larger
- 5:12concentric tube that could be filled
- 5:14with liquid sulfur dioxide, which he
- 5:16allowed to evaporate away to provide the
- 5:18evaporative cooling to lower the
- 5:20temperature of the capillary tube to
- 5:22-29°
- 5:23C.
- 5:24Separately, this large steel cylinder
- 5:26could be filled with water.
- 5:28Then by turning this massive wheel, a
- 5:31piston would be forced into the
- 5:32cylinder, which would increase the
- 5:34hydraulic pressure and force pressurized
- 5:36water through these metallic tubes. This
- 5:39water then fed into the mercury chamber,
- 5:41which forced it upwards like a liquid
- 5:43piston, compressing the oxygen above it
- 5:46to a pressure of 300 atmospheres. But
- 5:49even under this intense pressure and low
- 5:51temperature, the oxygen still remained a
- 5:53gas.
- 5:54But here's where it gets really cool,
- 5:56literally. When he released the water
- 5:58pressure, the mercury quickly dropped,
- 6:01causing the gas pressure to rapidly
- 6:02plummet down to atmospheric pressure. By
- 6:05his calculation, this caused a
- 6:06temperature of at least 200 degrees
- 6:09below the starting point.
- 6:11He said that, as a result, we had once
- 6:13see a heavy mist caused by the
- 6:15liquefaction or even perhaps the
- 6:16solidification of the oxygen.
- 6:19This made Cailletet the first person in
- 6:21history to liquefy oxygen. And not only
- 6:24that, shortly afterwards he managed to
- 6:26produce a mist from nitrogen as well.
- 6:28But there was a problem.
- 6:30The mists only stuck around for a couple
- 6:32of seconds before evaporating again.
- 6:35Even though Cailletet was technically
- 6:36successful, if scientists wanted to
- 6:38actually study these liquids, they'd
- 6:40need an even more extreme setup. So why
- 6:43don't we get a steam engine involved?
- 6:46You see, at the exact same time that
- 6:48Cailletet was performing his
- 6:49experiments, a Swiss physicist called
- 6:51Raoul Pictet was working on the same
- 6:53problem. And just 20 days after
- 6:55Cailletet's experiment, Pictet performed
- 6:58an incredible experiment of his own
- 7:00using this beauty.
- 7:02Let me tell you how it worked by looking
- 7:03at an original schematic. Everything you
- 7:06see here is a closed loop.
- 7:08Tube K is part of another loop that fits
- 7:10inside tube C. We'll come back to that
- 7:12in a minute. Tube C was filled with
- 7:14sulfur dioxide and attached to a pump
- 7:17that rapidly decreased its pressure,
- 7:19causing evaporative cooling.
- 7:21Pictet reported that the temperatures
- 7:22here dropped to -65°C.
- 7:25The SO2 gas was then pumped down here,
- 7:28where another pump increased its
- 7:29pressure to condense it back into a
- 7:31liquid.
- 7:32To remove the heat produced by this
- 7:34pressure increase and help the SO2
- 7:36condense, this condenser was cooled with
- 7:38a constant stream of cold water, leaving
- 7:41the liquid SO2 at around 25°C.
- 7:44This liquid was then returned to tube C,
- 7:47where the cycle repeated, keeping the
- 7:48inner tube K at a chilly -65°C.
- 7:53Above, we have another closed loop, very
- 7:55similar to the first, but this time
- 7:57containing carbon dioxide.
- 7:59Tube M is part of yet another system
- 8:01which we'll come back to, but it's sat
- 8:03inside tube H.
- 8:05Let's start with tube K nestled inside
- 8:07tube C at -65° C.
- 8:10This tube is where the carbon dioxide
- 8:12was pressurized and condensed into a
- 8:14liquid.
- 8:15Just like the cold water condenser
- 8:16below, tube K removed the heat from the
- 8:19CO2 to help it condense. This very cold
- 8:22liquid then returned to tube H where
- 8:25another pump rapidly reduced the
- 8:26pressure resulting in evaporative
- 8:28cooling which Pictet reported to drop
- 8:30the temperature even further to around
- 8:32-140°
- 8:34C. So essentially we have multiple
- 8:36coolants each allowing the next to get
- 8:39even colder.
- 8:40Vessel L contained potassium chlorate
- 8:43which was heated to release oxygen gas
- 8:45which built up in tube M at the low
- 8:47temperature of -140°
- 8:49C.
- 8:50The whole system was left for several
- 8:52hours until the oxygen pressure was at
- 8:54320 atmospheres whilst a 15 horsepower
- 8:58steam engine was driving the pumps for
- 9:00the refrigeration. But here's where the
- 9:02magic happens. To drop the temperature
- 9:04further, Pictet used the same principle
- 9:07as Cailletet
- 9:08cooling through expansion which he could
- 9:10do by opening valve P.
- 9:13As Pictet said in his paper, when
- 9:15opening P is suddenly uncovered, the
- 9:17oxygen escapes violently producing an
- 9:19expansion and an absorption of heat
- 9:21sufficiently great for a liquefied
- 9:23portion to appear in the glass tube and
- 9:26to spurt through the opening when the
- 9:27apparatus is inclined.
- 9:29How amazing is that?
- 9:31Pictet was able to recreate this
- 9:32dramatic jet of liquid oxygen multiple
- 9:35times in front of the Physical Society
- 9:36of Geneva and in later experiments he
- 9:39was able to create liquid jets of
- 9:40nitrogen as well. Now obviously these
- 9:43jets of liquid oxygen and nitrogen would
- 9:45immediately evaporate again but it
- 9:47seemed like scientists were right on the
- 9:49cusp of being able to collect them and
- 9:51keep them in liquid form. It would take
- 9:53just over 5 years for the first
- 9:55scientists to confidently report that
- 9:57they had condensed oxygen under more
- 9:59consistent circumstances and seen the
- 10:01stable liquid sitting in a tube with
- 10:03their own eyes.
- 10:05This report came from Kraków in Poland
- 10:08in April 1883.
- 10:10Two scientists, Karol Olszewski and
- 10:13Zygmunt Wróblewski, used Pictet's
- 10:15approach of using coolants to cool other
- 10:17coolants,
- 10:18but they used a coolant and a setup that
- 10:20seemed to work a lot better.
- 10:22That coolant was ethene gas, and check
- 10:25out their apparatus.
- 10:27Vessel X contained ethene, which was
- 10:29liquefied under pressure. It was passed
- 10:32through coil B, which was surrounded
- 10:34with dry ice and ether to cool it
- 10:35further, and deposited in vessel S,
- 10:38which was also connected to a pump,
- 10:40resulting in the evaporative cooling of
- 10:42the ethene to drop the temperature down
- 10:43to -130°
- 10:46C.
- 10:47Also submerged in vessel S was a tube
- 10:49containing pressurized oxygen, which was
- 10:51pressurized in the apparatus down here
- 10:53to over 20 atmospheres, and this time
- 10:56they didn't need to suddenly release the
- 10:58pressure.
- 10:59The oxygen condensed and collected at
- 11:00the bottom of the tube.
- 11:02At the top of this column of liquid,
- 11:04they could see a clearly defined curved
- 11:06surface, a meniscus, just like what
- 11:08you'd see in a narrow tube of water.
- 11:11After all those fleeting mists and
- 11:13violent jets, here was a recognizable
- 11:15body of liquid oxygen
- 11:18sitting inside a tube long enough for
- 11:19them to examine it and measure its vapor
- 11:21pressure at different temperatures.
- 11:23Later, they were able to condense
- 11:25nitrogen and observe its meniscus, but
- 11:27this liquid only lasted for a few
- 11:29seconds before evaporating again.
- 11:31Finally, two of the three permanent
- 11:33gases had been tamed. Unfortunately,
- 11:36they were still unable to condense the
- 11:38third.
- 11:39But the next question was obvious.
- 11:41Could these newly liquefied gases help
- 11:43scientists reach the even lower
- 11:45temperatures needed to finally liquefy
- 11:47hydrogen?
- 11:48Well, Olszewski and Wróblewski tried it,
- 11:51and although they did report fleeting
- 11:52signs of hydrogen condensation,
- 11:55obtaining a clearly visible liquid that
- 11:57they could collect remained just out of
- 11:59their reach.
- 12:00Hydrogen needed something more.
- 12:03In the mid-1890s, the Scottish chemist
- 12:05James Dewar made a huge breakthrough.
- 12:08Dewar knew from firsthand experience the
- 12:10dangers of working with pressurized
- 12:12gases. He'd accidentally mixed liquid
- 12:14oxygen with ethene, resulting in an
- 12:16explosion that had almost killed him.
- 12:19But he was determined to continue his
- 12:21research.
- 12:22Up until this point in the story,
- 12:23scientists had been using one coolant to
- 12:25cool another.
- 12:26But Dewar wanted to also use the
- 12:28hydrogen to cool itself.
- 12:31This is a concept called regenerative
- 12:32cooling, and I'll explain how it worked
- 12:34by looking at Dewar's genius setup.
- 12:37He passed compressed hydrogen from tank
- 12:39A through a coil in vessel B.
- 12:42This contained our classic carbon
- 12:44dioxide bath, which was being pumped
- 12:45away to make it even cooler.
- 12:47Then the hydrogen passed into the next
- 12:49coil in vessel C, which actually
- 12:51contained liquid air, which if you think
- 12:53about it is essentially just a mixture
- 12:55of liquid oxygen and liquid nitrogen.
- 12:57This cooled the hydrogen down further to
- 12:59around -190°
- 13:02C, the lowest coolant temperature we've
- 13:04seen so far.
- 13:06After this, the hydrogen passed into
- 13:08another coil where at the bottom it was
- 13:10allowed to escape through a nozzle.
- 13:12This was the genius part.
- 13:14As we've seen multiple times already,
- 13:16the cold gas rapidly expanded and cooled
- 13:19further.
- 13:20It then flowed around the coil, cooling
- 13:22the compressed gas inside even more,
- 13:24which would escape through the nozzle
- 13:26and the cycle would repeat,
- 13:27progressively dropping the temperature
- 13:29of any gas in the coil.
- 13:31Using this setup, Dewar dropped the
- 13:33temperature of the hydrogen so much in
- 13:35just a few minutes that similar to
- 13:37Pictet, he was able to create a jet
- 13:39containing liquid hydrogen that sprayed
- 13:41out of opening E when he opened the
- 13:43valve.
- 13:44But making the liquid was one thing.
- 13:46Getting it into a container without it
- 13:48immediately disappearing was another.
- 13:51Something to remember here is just how
- 13:52dangerous this all was. During one
- 13:55experiment, Dewar's assistant Robert
- 13:57Lennox lost an eye in an explosion. You
- 13:59can see him depicted here in this
- 14:01painting of Dewar lecturing to the Royal
- 14:03Institution, turned away from the
- 14:05audience to hide his scars.
- 14:07On the 10th of May 1898, Dewar used a
- 14:10modified version of his apparatus to
- 14:12finally collect liquid hydrogen.
- 14:15The main difference was the outlet,
- 14:16which he directed into a special vessel
- 14:18that he'd invented previously.
- 14:20It had a vacuum in its walls to
- 14:22massively reduce the heat entering from
- 14:24the surroundings.
- 14:25This Dewar flask or vacuum flask is
- 14:28exactly how you're able to keep your
- 14:29coffee hot for hours on end.
- 14:31Dewar used layers of these flasks to
- 14:33insulate the liquid hydrogen enough to
- 14:35actually collect around 20 ml of it.
- 14:38After about 5 minutes, the flow stopped.
- 14:41Traces of air in the hydrogen had frozen
- 14:44inside the pipes and blocked the jet.
- 14:47Imagine that. The apparatus was so cold
- 14:49that air itself had frozen solid and
- 14:52become a physical obstruction.
- 14:54The liquid hydrogen itself was clear and
- 14:56colorless with a sharply defined
- 14:58meniscus.
- 14:59After decades of attempts, oxygen,
- 15:02nitrogen, and now hydrogen had all been
- 15:04liquefied. And liquid hydrogen now gave
- 15:07scientists a way to reach colder
- 15:09conditions still, which was fortunate
- 15:11because another gas had just entered the
- 15:13picture,
- 15:14helium.
- 15:15Could they use their newest liquid to
- 15:17overcome that final challenge?
- 15:19The answer came from Leiden in the
- 15:21Netherlands on the 10th of July 1908
- 15:24when the Dutch physicist Heike
- 15:25Kamerlingh Onnes used this apparatus to
- 15:28achieve the coldest temperature that had
- 15:30ever been recorded on planet Earth
- 15:32before.
- 15:33I won't go through this entire beast of
- 15:35a schematic because the principle is
- 15:36essentially the same as what we've seen
- 15:38already. Multiple levels of coolants,
- 15:40now including liquid hydrogen, along
- 15:43with both evaporative and regenerative
- 15:45cooling. But one genius addition he
- 15:47borrowed from Dewar was the use of a
- 15:49charcoal purifier.
- 15:51The helium would pass through some
- 15:53charcoal where any contaminating air
- 15:55molecules would adsorb to the surface,
- 15:57thus removing it from the helium and
- 15:59preventing any air from freezing solid
- 16:01and blocking up the lines as they had in
- 16:03Dewar's earlier experiment. Using this
- 16:06amazing setup, he was able to get the
- 16:08temperature down to under 5 Kelvin.
- 16:11That's less than
- 16:13above absolute zero. It's unfathomably
- 16:16cold.
- 16:17But the experiment wasn't giving him an
- 16:19obvious sign of success.
- 16:21He kept it going, connected the last
- 16:23bottle of liquid hydrogen and still
- 16:25couldn't see the liquid helium they were
- 16:27looking for.
- 16:28Then a colleague watching the experiment
- 16:30noticed something odd.
- 16:32The thermometer had become unusually
- 16:33steady. He said that it was behaving as
- 16:36though it was already sitting in a
- 16:37liquid.
- 16:38Could they have succeeded without even
- 16:40noticing?
- 16:41They shone a light into the vessel from
- 16:42below and there it was, a sharply
- 16:45defined liquid surface.
- 16:47The helium had condensed, but they
- 16:49hadn't been able to see it.
- 16:51Five years later in 1913, Onnes received
- 16:54the Nobel Prize in physics for his
- 16:56investigations of matter at low
- 16:57temperatures, including the production
- 16:59of liquid helium.
- 17:01What a saga.
- 17:04We have come such a long way from
- 17:06Faraday condensing chlorine with a
- 17:08syringe is actually crazy to think
- 17:10about.
- 17:10This is why I find these stories so
- 17:12beautiful and inspiring. Every
- 17:14breakthrough began with something that
- 17:16wouldn't work and someone determined to
- 17:19understand why. The gases weren't
- 17:21permanent. The limits were just further
- 17:23away than anyone had managed to reach.
- 17:26But since when were limits ever going to
- 17:28hold us back?
- 17:29Thanks so much for watching. This video
- 17:32was a saga of its own to research,
- 17:34animate and put together, all of which I
- 17:35do entirely by myself. So if you made it
- 17:37this far and you'd like to support the
- 17:39channel to help me make the next video,
- 17:41please check out my Patreon or my merch
- 17:42store. Or if you'd rather not, that's
- 17:44cool too. I appreciate you watching and
- 17:46I'll see you in the next one.
- 17:48Woah.
About this transcript
This page contains the full transcript of Before Fridges, Scientists Liquefied Air - Here's How by Chemistorian, generated from the public captions YouTube serves with the video. The transcript has 2,967 words across 514 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.