Atomic Absorption Spectroscopy — Transcript
Full transcript
- 0:10This video will demonstrate calcium concentration quantification in milk
- 0:14using the atomic absorption spectroscopy technique.
- 0:18Here is the equipment you will need.
- 0:26Let’s begin with the sample.
- 0:28Weigh 1.0 g of milk into a 50 mL Erlenmeyer flask, perform in triplicates.
- 0:35For the sample blank, weigh 1.0 g of dd water instead, do this only once.
- 0:42Inside the fume hood, add 5.0 mL of concentrated nitric acid
- 0:48and 1.0 mL of 30% hydrogen peroxide
- 0:52to each sample and sample blank.
- 0:54Please note that the fumes created by the reaction will be very toxic.
- 1:00Setup the hot plate in the fume hood and heat the flasks at medium heat.
- 1:05Swirl occasionally.
- 1:07Your solution should change from cloudy to dark orange-brown, to clear pale,
- 1:12while your blank should stay clear.
- 1:15If your solution is still orange-brown after 20 minutes,
- 1:18add an extra 2.5 mL of nitric acid and 0.5 mL of 30% H2O2
- 1:26and continue to heat.
- 1:28It is possible to obtain a clear yellow solution if you put an excess amount of nitric acid
- 1:34but it does not affect the result.
- 1:36After heating, transfer the samples and blank separately into 100 mL volumetric flasks.
- 1:43Rinse each Erlenmeyer flask with dd water
- 1:46and add it to the volumetric flask and make up to volume.
- 1:49Invert a few times to mix.
- 1:51Next, pipette 1.0 mL of each sample or blank to corresponding 10 mL volumetric flasks.
- 1:59Add the appropriate volume of 2.5% lanthanum oxide solution
- 2:04to each flask to obtain a 0.5% final concentration,
- 2:09and make up to volume with dd water.
- 2:12Invert a few times to mix.
- 2:14During the wait time in the sample preparation steps, you can begin preparing your standards.
- 2:20First, dilute the 0.05 milliequivalent calcium chloride standard solution by pipetting an
- 2:27appropriate amount of the solution into a 100 mL volumetric flask
- 2:32labeled 100 micrograms Ca/mL.
- 2:35Add dd water to volume.
- 2:38Invert a few times to mix.
- 2:41Then label the 25 mL volumetric flasks with concentrations
- 2:450, 0.5, 1.0, and 2.0 micrograms Ca/mL.
- 2:52Pipette the required amount of the 100 µg Ca/mL solution into
- 2:58each of the 25 mL volumetric flasks.
- 3:01Then pipette the required amount of 2.5% lanthanum oxide solution
- 3:06to obtain 0.5% lanthanum oxide in the standards.
- 3:11Make up to volume with dd water, and invert to mix.
- 3:15All samples and standards will be measured using the atomic absorption spectrophotometer.
- 3:21Bring your samples and standards together with dd water to the instrument.
- 3:25Your TA will briefly show you how to ignite the flame.
- 3:29You must assemble the sample slot, ensuring that it is screwed on tightly.
- 3:34Otherwise, you will observe leaks when dd water is being fed into the instrument.
- 3:38Turn on power switch of the instrument.
- 3:41Then turn on the acetylene gas tank.
- 3:43Next turn on the air flow.
- 3:45Adjust the air flow and fuel to the appropriate level.
- 3:50Turn the control to AIR, while lighting the flame with a lighter.
- 3:54Turn the fuel to ON position.
- 3:57You should observe a nice blue flame about 2 inches tall.
- 4:00Please note that it is important to follow the proper order to ignite the flame or you
- 4:05will create a lot of ashes but fail to ignite the flame.
- 4:09Now the instrument is ready.
- 4:11Place the sample feeding tube in dd water first,
- 4:14until there is a constant violet blue colour.
- 4:17Pay attention if there is any leak around the sample slot.
- 4:20Zero the spectrophotometer by pressing the AZ button while feeding dd water.
- 4:26You should start with the standard with the lowest concentration.
- 4:29Dip the feeding tube into the standard solution, the flame should turn green.
- 4:33Record the reading and dip the tube back in the dd water to rinse.
- 4:37Continue with all standards, then the sample blank, and finally your samples.
- 4:43When completed, flush the sample slot with dd water.
- 4:46Your TA will turn off the instrument for you.
- 4:49Discard your samples, sample blank and standards into containers labeled lanthanum oxide wastes.
About this transcript
This page contains the full transcript of Atomic Absorption Spectroscopy by FNH Teaching Lab, generated from the public captions YouTube serves with the video. The transcript has 656 words across 67 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.
What you can do with it
Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to choose a caption track available on the video.
Free YouTube transcript tool
YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, caption language selection, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.