YT YouTube2Text

YouTube2Text → Transcripts → 18.0 Line Fill Advance (Eng) || Full Tutorial For Beginners || StitchMax India

18.0 Line Fill Advance (Eng) || Full Tutorial For Beginners || StitchMax India — Transcript

by Stitchmax India · 3,618 words · 560 segments · language en · Watch on YouTube

Open in transcriber Summarize with AI Download SRT/VTT

Full transcript

0:00[Music]
0:05Hello friends last topic we learned was
0:07create motive today we will learn about
0:10line fill Advance motive we have points
0:13inside it user style sequin Style on
0:16line line on style backtrack mirror
0:19backtrack mirror style F backtrack
0:21mirror next frame change frame at nodes
0:24Force last frame on last Stitch track on
0:27style name Stitch length percent alter
0:29mode height mirror alternative motive
0:32omit first Stitch omit last Stitch omit
0:35first motive omit last motive ecommand
0:38with sty start and end at first Stitch
0:41first Gap Stitch half last Stitch use
0:44Gap Stitch as Stitch no Gap Stitch at
0:47end add Gap stitches add alternative Gap
0:51stitches half back track track with
0:54alter sequin track with same sequin use
0:57bare raw style motive angle motive
1:00gradient gradient
1:03threshold so let's start with the first
1:06one which is user style
1:10sequin when we draw line fill we drop
1:13sequins on the nodes like
1:16this if we have to apply manually
1:19sequins on the Node then we can apply
1:21all the sequins press one to apply a
1:24squin press two to apply B squin press
1:26three to apply C squin we can set up to
1:2916 sequins here we have finished the
1:32drawing after that we need to continue
1:35with the combination of
1:38sequins moving forward we just need to
1:41continue drawing the sequence that have
1:43been dropped will not need to be dropped
1:48again for that we need to select the
1:50object and turn on the reshape
1:56mode yeah there is an option for a pend
2:00by clicking on it we will continue
2:10drawing then press
2:14enter after that in the advanced
2:16properties of line fill there is an
2:18option for user style
2:20squin we need to turn it on then the
2:24combination of sequence that we had set
2:26earlier will be applied throughout the
2:28object
2:31after that we have options for Style on
2:33line and line on
2:36style J we create a sty using repeat
2:40count offset and Stitch
2:49Gap here we can see that the start point
2:53of the object is here and the end point
2:55is
2:58here the style that we have created
3:01manually using values doesn't show
3:03tracking
3:04above however if we join the start and
3:07end points then the tracking will become
3:13visible if we want to move this tracking
3:15to the Lower Side then in the advanced
3:18properties of line fill there is an
3:20option for Style on line and line on
3:22style we need to turn it
3:25on by turning on the option the tracking
3:28has moved to the bottom
3:32after that is the back trck
3:34mirror so here we make a stem
3:45Stitch we set its angle to 45 and the
3:48spacing we set to 2
3:50mm We join its start and end
3:54point you have to go to the advanced
3:57parameters of line fill and turn on the
3:59back track track
4:01mirror as it forms it will come forming
4:04on the opposite side in the same way
4:07here we draw a line and go to styles to
4:10select a style named round
4:12one we have reduced its length to 6
4:16mm We join its start and end points it
4:20is a style similar to half round after
4:23joining the start and end points if we
4:25need half round on the opposite side as
4:27well we can use the back track mirror
4:30for
4:35that so it will come like
4:39this after that comes the backtrack
4:41mirror style
4:50F if we need backtrack in this object
4:54but want to keep the start and end
4:56points
4:58separate
5:00where there is the end point it starts
5:02from there and ends at the same place
5:05but we have to start from the left side
5:07and end on the right
5:11side and the half round style we also
5:14have to do a backt track mirror on it so
5:17that the round comes on the opposite
5:19side with tracking for that we will use
5:22the back track mirror style
5:28left
5:33we will turn off the back track mirror
5:35from
5:38here from here this tracking will go
5:41under
5:44style then our style will be
5:51completed for that we have to use only
5:54one option backtrack mirror style
5:58f
6:00after that comes the backtrack mirror
6:02next
6:06frame for that we draw a line and
6:09applier
6:17Style We join it start and end points
6:22here there is an option for backtrack
6:24mirror next frame where we have selected
6:26one one and frame from and frame two
6:31here we have selected the frame with an
6:34outline and when it appears mirrored if
6:36we need a second frame for that we use
6:39the backtrack mirror next frame and
6:41along with it we must compulsorily keep
6:44the backtrack mirror
6:45on when we turn this on we can see here
6:49that we had selected one one in frame
6:51from and frame two so the second frame
6:54has come
6:58mirrored
7:00if we select the frame number two from
7:02here then the frame number two comes up
7:04here and the frame number three comes
7:08down this is the backtrack mirror next
7:12frame after that comes the change frame
7:15at
7:18node so for that we draw a line apply a
7:22style to it and will set the length to 6
7:28mm
7:30in the advanced properties of line fill
7:32there is an option here for change frame
7:34at nodes and when it is turned on it
7:37will look like
7:39this in frame from and frame two we have
7:42selected all
7:44frames now wherever we add a hard node
7:47the frame will change there we have
7:50added a hard node here so up to this
7:52point will be the first frame then the
7:54second frame will come then from here
7:57the third from here the fourth and in in
7:59this way we will continue changing
8:08frames so in this way wherever we at a
8:11hard node the second frame will be
8:13applied
8:25there after that comes Force last frame
8:28on last
8:32stitch for that we will draw a line and
8:35select the motif Luton to
8:40frame from here we will select the frame
8:43number one in the range from frame from
8:46to frame two here the last Stitch is not
8:49coming in to bring the Stitch you need
8:52to turn on the option of force last
8:54frame on last stitch in the advanced
8:56parameters of the line fill if you run
8:58the machine on this the tracking will go
9:01first and then all the stitches will be
9:03created right now we keep all
9:11frames after that we will run the
9:14machine and
9:15check after completing one frame when
9:18the second frame starts the machine will
9:21run
9:25twice when we select one in frame from
9:28and frame two the last Stitch does not
9:30come in the
9:32end so to bring the last Stitch you need
9:35to turn on the option of force last
9:37frame on last stitch in the advanced
9:40parameters of the line
9:52fill after that comes the track on
9:55style here we will draw a line set its
9:58length to 6 mm and use the motive named
10:02round one we will join its start and end
10:05points and this will introduce tracking
10:07where we drew the
10:09line we will hide connectors by press J
10:12shortcut
10:14key if we want the tracking to appear
10:17beneath the tracking style there is an
10:19option in the advanced properties of the
10:21line fill called track on
10:28Style enabling this option will make it
10:31go beneath the tracking style let's run
10:34the machine and see how it
10:40looks here tracking will go
10:49first after that the style will
10:53go after that is a named Stitch length
10:57percent with we will draw a line then
11:00apply a style to it for example Diamond
11:039
11:07face and set its length to 9
11:13mm if we want to make Only The Motif
11:16that is 9 mm the second motive smaller
11:19than that and the third Motif larger
11:21than that we need to create them in
11:23different
11:25sizes for that we use the named Stitch
11:29length
11:31percent for that we need to go to the
11:34object menu here the option is name and
11:37its shortcut key is control+
11:40alt+n when we press control+ alt+n the
11:44change name property will open whatever
11:47value we use here will function similar
11:49to a
11:56percentage here we need the first motor
11:59to be of the actual size so we are
12:01writing 100 here meaning we are writing
12:06100% to write the size of the second
12:09motive we first need to give a space and
12:12then we are writing the size of the
12:13second motive as
12:1680 we need to give a space again and
12:19then we have written 100 then again give
12:22a space and write 60 then again give a
12:25space write 100 then
12:27space if we need to increase the size of
12:30the motive by 20% Then here we will
12:33write 120 and then press
12:36okay in the advanced properties of line
12:39fill there is an option named Stitch
12:41length percent this option indicates
12:44that it will work in terms of
12:46percentages by turning this on and
12:48pressing okay you can set the Stitch
12:50length as a percentage of its original
12:52value here the first Motif has come out
12:55perfect at 9 mm and then it has been
12:58made 20%
13:07smaller we kept it at 100% here then 60%
13:12then again 100% And then 12 120% here
13:17according to the Stitch length The Motif
13:19has been adjusted but the height of the
13:21motif remains 9
13:25mm if you need to reduce the height as
13:28well according to the size then in the
13:30advanced parameters of line fill there
13:32is an option called alter motive height
13:35which needs to be turned
13:38on so this will reduce the height of the
13:41motive along with its size according to
13:44the percentage
13:48specified after that comes the mirror
13:51alternative motive
13:56option here we draw a line and and then
13:59select the style with Luton within it
14:02from here we will set the style height
14:04to 5
14:06mm here we can see that all the stitches
14:09of the lutan are coming down on the
14:11Downs side of the drawing if we want one
14:14stitch on the downside and one stitch on
14:16the upside meaning all stitches should
14:20alternate in the advanced parameters of
14:23line fill there is an option here for
14:25Mirror alternative
14:27motive
14:31you have to turn on the option and then
14:33it will create an alternative mirror
14:35effect on the
14:37motive after that comes the omit first
14:44Stitch here we will draw a
14:49line if we want to skip this first
14:52Stitch then in the advanced properties
14:54of line fill there is an option here
14:56called umit first Stitch which needs to
14:58be turned
15:06on if we need to remove the last Stitch
15:09then there is an option for that called
15:11omit last
15:15Stitch here we can see the drawing on
15:17both sides the object starts from here
15:21and ends here in this the first and the
15:24last Stitch have been
15:25skipped after that there is the omit
15:28first motive option here we will draw a
15:32line and then select the
15:39style here if we want to skip the first
15:42motive then in the advanced parameters
15:44of line fill there is an option called
15:47umit first motive which we need to turn
15:54on if we need to skip the last motive
15:57then in the advanced option
15:59there is an option called omit last
16:07motive after that comes the E command
16:10with
16:14style here we go to the application
16:17property and turn on while routine
16:19command skip next
16:24node after that we will manually go to
16:27the location where we want to drop the
16:28sequin and press C on the mouse
16:36there in the same way we will now drop
16:39sequins at all the designated
16:50places within this the stitches here are
16:53required as they are but where the
16:55sequins have been dropped we need to
16:57apply a specific style
17:00there for example we will apply a back
17:03stitch here so as you can see here the
17:06sequin has been applied to the entire
17:09object to apply the style only where the
17:12sequins were dropped we need to go to
17:15the advanced parameters of line fill
17:18there you will find an option called e
17:20command with style this option needs to
17:23be turned
17:27on
17:30here we can see that the style has been
17:32applied only at the places where the
17:34sequins were
17:37dropped after that comes the option
17:39start and end that first
17:43Stitch we will draw a line here apply a
17:46motive named single then apply sequins
17:49and in this way we will arrange the
17:51placement of the
17:57line we can you can see that the routine
17:59starts from here when it proceeds to
18:02create another line tracking occurs at
18:05this
18:10point we do not want this tracking to
18:13occur here but rather where the sequence
18:15starts for this purpose we use the start
18:19and end at first Stitch
18:23feature in the advanced parameters of
18:26line fill there is an option called
18:28start and end at first
18:32Stitch turning on this option will move
18:34the tracking to above the first
18:40sequin initially it appeared like this
18:43and after turning on start and end at
18:45first Stitch it will look something like
18:51this let's run the machine and see after
18:55the routine of the first line is
18:57finished it will will then execute one
18:59more Stitch and afterwards the upper
19:01objects will be
19:10created after that comes the first Gap
19:12Stitch
19:15option here we have drawn a line and
19:18applied a style to
19:23it here if we want to skip the first
19:26motive there is an option in the
19:28Advanced properties of line fill called
19:30first Gap Stitch we need to turn this
19:33option
19:38on after that comes the half last Stitch
19:45option we have drawn a line here and we
19:48need the last Stitch of this line to be
19:50only
19:51half the Stitch length is 3 mm so we
19:55want the last Stitch to be 1.5 mm
20:00for this we will use the half last
20:06Stitch so here it has become 1.5
20:10mm our object extends up to this point
20:14and the last stitch has been reduced to
20:16half after that comes the option use Gap
20:19Stitch as Stitch we draw a line
20:25here then select a style and set its
20:28length to 6
20:36mm after that we will set 3 mm in the
20:39Stitch
20:41Gap to match the 3 mm Stitch Gap add a
20:45motif of the same size turn on use Gap
20:49Stitch as Stitch in line fill Advanced
20:57properties
21:01to make the object the same size in
21:03length and height use the alter motive
21:06height option in advanced
21:12properties so it becomes
21:16perfect after that comes no Gap Stitch
21:18at
21:22end here we draw a line and select the
21:25style inside
21:27it
21:32after selecting the style we will apply
21:34a stitch Gap equal to the length we have
21:41set here we can see that there is a gap
21:43at the end of the
21:46style the style we have used here is
21:48what we need in the advanced parameters
21:52of line fill there is an option here for
21:54no Gap Stitch at
21:57end
21:59if we turn this on then the Stitch
22:01appears where there was a gap at the
22:07end after that comes at Gap
22:11Stitch here we will draw a line then
22:14apply a style to
22:26it here we need to run one stitch and
22:30leave a gap so for that we can use at
22:32Gap
22:38Stitch the Gap has been applied here if
22:42we want the gap size to be the same as
22:44the size of The Motif in the Stitch
22:46length then for that we use at Gap
22:55Stitch after that comes at alter ative
22:58Gap
23:01Stitch here there is one stitch and then
23:04a gap where the Gap is we need to add
23:07the same style in a different
23:13color for that we need to copy and paste
23:16this object then we will change its
23:19color The Motif in yellow color we need
23:22it in place of the
23:26gap for that we will use add alternative
23:29Gap
23:30stitch in the style with the green color
23:33we had only used add Gap
23:36stitch in the motive for the yellow
23:39color we used both a gap Stitch and an
23:41alternative Gap Stitch that's why the
23:44Gap in it has become
23:51alternate after that comes the half back
23:56track here we draw a line set the Stitch
23:59length to 3.0 mm then go to style and
24:03select the style named
24:08single then we will turn on the squin
24:11and here we can see that during
24:13operation the squin is dropping on every
24:21Stitch if we join the start and end
24:24points then when tracking occurs
24:26stitches should appear when where the
24:28squin is and there should also be
24:30stitches beside the
24:36squin for that we use the Advanced
24:39Property of line fill called half backt
24:48trck after the sequin drops on every
24:51Stitch when the tracking runs it drops
24:53stitches on both sides of the squin
24:56which locks the squin in place
25:02place for that in the Advanced Property
25:05of line fill it is necessary to turn on
25:08half backt track and also enable Style
25:10on line line on
25:16style after that comes track with alter
25:22sequin we will draw a line here and set
25:25the number of runs to two then select
25:27the style as single then press
25:33okay after that we will use to sequins A
25:36and B here in the first sequin type we
25:39select a sequin and in the second we
25:41select B
25:50sequin when we run the machine here and
25:52observe it forms by dropping both these
25:56sequins
26:01when we keep the start and end points
26:03joined the first sequin that we have
26:05applied here continues to form during
26:07the
26:08tracking the second squin that we have
26:11taken should run during the return
26:13time for that we will use the Advanced
26:16Property of line fill where there is an
26:18option track with alter sequin we will
26:20turn it
26:24on so here we can see it drops the a
26:28sequin while making the tracking and
26:29comes back dropping the B sequin while
26:41returning after that comes track with
26:44same
26:45sequin here we will draw a line and join
26:48its start and end
26:53points here we are setting the number of
26:56runs to to then we are app applying
26:57single in
26:59style in this we will turn on the squin
27:02and here we can see that there are 15 a
27:05sequins in this
27:08object if we want to sequence in the
27:10tracking as well as during the return
27:12then we can use track with same squin in
27:15the Advanced Property of line
27:22fill here where there were 15 sequins
27:25now there are 30 so it will drop
27:27sequence in the tracking as well we can
27:31also see this in the Stitch
27:34position and it will also drop sequence
27:37while
27:38returning after that comes the use bar
27:40row
27:44style for that we create an object of
27:47water fill
27:52here and inside it we will select the
27:55style leton
28:04inside this we have turned on the squin
28:07and here we can see that the Luton has
28:09taken the shape of the drawing so if we
28:12want its angle to be 90° on the
28:21downside here each leton sequin is
28:24required on the downside for us so for
28:26that in the line fill Advanced Property
28:29the option to use bar row style is
28:31available here it needs to be turned
28:34on so here the Luton has come on the
28:41downside after that comes the motive
28:46angle here we will draw a line and in it
28:50we will select the style as lutken and
28:52set the dense style height to 5 mm here
28:56the angle of the Lut is
28:5890° if we want to change the angle we
29:01can do so in the Advanced Property of
29:03line fill there is an option here called
29:07motive angle that allows us to change
29:09the
29:12angle this way we can set different
29:15angle as per a
29:26preference
29:32after that is the motive
29:34gradient here we will draw a line and
29:37select the
29:42style now here we have set the size to 8
29:47mm if we want to make it smaller for
29:49each motive based on its percentage then
29:52in the parameters of line fill there is
29:54an option here called motive gradient
30:00just like we used the named Stitch
30:02length this works based on the
30:05percentage here the motive is made at
30:08100% if we want another motive to be 2%
30:12smaller than that we can adjust it
30:15here here we will write 98 then press
30:19okay and now we can see that each motive
30:22is coming to percent
30:26smaller
30:35if we want to reduce its height as well
30:37then we will use the alter motive height
30:39option for
30:43that the first Motif was 8 mm and the
30:46last Motif is 1.61
30:53mm this small object is not effective so
30:56we need to restrict it to finish at
30:58either 50% or
31:0140% subsequently the 40% motive
31:07continues for that in the Advanced
31:10Property of line fill there is an option
31:12called gradient
31:14threshold here we set it to
31:2050% so here our Motif which was
31:23originally 8 mm will only continue until
31:264 mm in the end so here we can see that
31:30the motive has become 4
31:36mm if we look at the last side we will
31:39see that all motivs are 4
31:43mm if we look at the start side we will
31:46see that the motivs are
31:56larger

About this transcript

This page contains the full transcript of 18.0 Line Fill Advance (Eng) || Full Tutorial For Beginners || StitchMax India by Stitchmax India, generated from the public captions YouTube serves with the video. The transcript has 3,618 words across 560 segments, with the original timestamps preserved so you can click any line to jump to that moment in the embedded player.

What you can do with it

Use the transcript to take notes, quote the speaker, build a study guide, generate a summary with ChatGPT or Claude via the YouTube Summary tool, or export it as a timed subtitle file with YouTube to SRT. You can also re-open it in the transcriber to translate the transcript into 100+ languages.

Free YouTube transcript tool

YouTube2Text is a free YouTube transcript generator — no signup, no daily limit. Paste any YouTube link and get the full transcript instantly, with timestamps, click-to-jump, translation to 100+ languages, AI prompts for ChatGPT, Claude, and Gemini, and exports to TXT, SRT, VTT, or Markdown.